RC Lighting PLF13 Manuale utente
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
RC’s PL floods must be wired in accordance with
the National Electrical Code and applicable local
codes. Proper grounding is required for safety.
The PL floods are for outdoor use and should not be
used in areas of limited ventilation or high ambient
temperatures. All work should be done by a qualified
electrician.
Fixture should be located at least 18" below any
overhang or other structural detail. Fixture should
not be recessed.
WARNING: Make sure power is OFF before installing or maintaining fixture.
CAUTION: To avoid a possible shock hazard, do not connect wires until fixture is twisted into mounting hole.
LOCATION
The PL floods can be mounted to any 1/2’’ NPS
mounting hole.
1. Route fixture leads through the mounting hole.
2. Twist PL flood foot into mounting hole.
3. Tighten locknut.
MOUNTING
(over)
Thank you for buying RC Lighting fixtures. Our aim is to design the best quality products so you can get the job
done right. We’d like to hear your comments. Call us at 888-722-1000, attention Marketing Department.
PLF13 AND PLF26 FLUORESCENT FLOODS
Installation Instructions Listed
For Wet
Locations
WIRING
Use supply wire rated for 90°C.
1. Connect the fixture lead to the black supply lead.
2.
Connect the common fixture lead to white supply lead.
3.
Connect supply ground wire to fixture ground screw
.
PLF
LIGHT
FIXTURE
BLACK BLACK
WHITE
(–) COMMON
GROUND
SUPPLY
1. Loosen swivel bolt.
2.
Aim as desired.
3. Retighten swivel bolt.
1. Disconnect power.
2.
Make sure fixture and lamp are cool enough to
touch.
3. Remove screws from front of lens and remove
lens.
4. Insert lamp base into socket so that pins in the
lamp are inserted securely into the socket(s).
5. Re-fasten lens to fixture.
AIMING
RE-LAMPING
CAUTION: Prior to installing, check that the lamp(s) is of proper type and wattage. Observe lamp manufacturer’s
recommendations on the lamp operation, ballast type and burning positions.
CAUTION: Be sure fixture temperature is cool
enough to touch. Be sure power is off.
Clean reflector and polycarbonate refractor with a cloth
moistened with non abrasive glass cleaning solution.
Check that:
1. Proper lamp is installed. Lamp is not faulty.
2. Line voltage at the fixture is proper.
3. Fixture is wired properly.
4. Fixture is grounded properly.
CLEANING
TROUBLE SHOOTING CHECKLIST
Swivel Screw
Lens
Socket
PLF13 AND PLF26
INSTALLATION INSTRUCTIONS
(continued)
Catalog #
Lamp and socket type
PLF13 13 watt Quad, GX23 base
PLF26 (2) 13 watt Quad, GX23 base
Toll free fax: e-mail:
Send a fax to
888 722-1232
Tech Help Line:
Call our experts
888 722-1000
Visit our website for
product info
Easy Answers
rclighting.ca:
Get answers promptly
The designs of RC Lighting fixtures are protected under Canadian, U.S. and international intellectual property laws, © 2010 RC Lighting
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali RC Lighting Apparecchio di illuminazione
Manuali Apparecchio di illuminazione popolari di altre marche
Emos
Emos CLASSIC ZY1431T Manuale utente
Westinghouse
Westinghouse Outdoor Lighting Fixture Manuale utente
Hedler
Hedler C 12 silent Manuale utente
Blizzard Lighting
Blizzard Lighting Puck: CSI Manuale utente
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Manuale utente
Lightmaxx
Lightmaxx Shaft 5R Manuale utente
Cooper Lighting
Cooper Lighting Halo L3232E Manuale utente
Stageline
Stageline ODW-2410RGBW Manuale utente
Light Sky
Light Sky Tornado Series Manuale utente
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Manuale utente
Lightolier
Lightolier Lytespan 83ED17S Manuale utente
Lightolier
Lightolier Calculite CS8226 Manuale utente