Rc-tool Alti-DX2 Manuale utente

User’s Manual Altimeter Sensor

Alti-DX2

January 2020

The Alti-DX2 is an altimeter sensor for Spektrum telemetry

receivers with X-BUS port or the Spektrum telemetry module

TM 000.

Alti-DX2 measures the current altitude above ground level.

The Alti-DX2 is designed specifically for model aircrafts, where

smallest dimensions, very low weight and simple handling is

required.

It is equipped with a barometric sensor and a 32-bit processor

and therefore has an excellent sensitivity and a fast response

time.

Alti-DX2 is connected directly to a Spektrum telemetry receiver

or the Spektrum telemetry module TM 000. No separate power

supply is required.

Figure 1: Altimeter Sensor Alti-DX2

Installation

Alti-DX2 is connected to the X-BUS port of a Spektrum telemetry

receiver or the Spektrum telemetry module TM 000 via the

cable supplied.

After power on the receiver, the Alti-DX2 calibrates to the

surrounding air pressure and transmits an altitude of zero

meters. If the sensor is moved up or down, the measured

altitude is transmitted to the transmitter via the telemetry

system.

The height can be displayed in feet or meters. The corresponding

setting must be made on the transmitter.

The following steps show how to setup the Spektrum DX6 G2/G3

transmitter (software version 2.05).

The setting process for other transmitters, receivers and

soft are versions may differ slightly from the procedure

described here. The description is therefore only for guidance:

. Power off the transmitter

2. Connect Alti-DX2 to the "X-BUS" port and if the TM 000 is

used connect the "DATA" port to the "DAT" port of the

receiver.

Figure 2: Connection Scheme Alti-DX2 - TM1000 - Receiver

3. Press and hold the "BND" button on the TM 000 while the

receiver is connected to the power supply. The LED of the

receiver starts flashing and is waiting for the "bind" signal

from the transmitter.

4. Switch on the transmitter with the scroll wheel pressed.

Select "Bind" in the "System Setups" menu (Fig. 3).

Figure 3: The “Bind function in the System Setup

5. In the “Bind” menu click “Bind” (Fig. 4)

Figure 4: The “Bind menu

User’s Manual Altimeter Sensor

Alti-DX2

January 2020

6. The binding process was successful when both the receiver

(DSMX 22ms) and "Telemetry" were recognized (Fig. 5).

Figure 5: Binding was successful: Receiver and Telemetry

detected

7. Press the scroll wheel to access the "Function List" and

select "Telemetry" (Fig. 6).

Figure 6: “Telemetry in der Function List

8. To integrate Alti-DX2 the “Auto Configuration” function

must be used:

a. Power on the transmitter, then power on the receiver

b. Delete all Altitude and Vario sensors in the telemetry

c. Select Telemetry >> Settings >> Auto-Config in the

Function List (Fig. 7)

Figure 7: “Auto-Configuration Function in the Telemetry menu

9. Click on "Altitude" at position “4” and if required adjust the

alarms.

Installation in the model aircraft

Since the altitude is determined by measuring the surrounding

air pressure, the installation location should be as free from

drafts as possible. Rapidly moving air over surfaces can create

pressure differences that lead to deviating measurement results.

For this reason, altimeters should never be installed outside the

model aircraft. The optimal installation location is usually

protected from wind within the fuselage of your model aircraft.

Use double-sided adhesive tape or servo tape on the back of the

Alti-DX2 for fastening.

The Alti-DX2 measures air pressure. Therefore, do not wrap the

Alti-DX2 in air-impermeable plastic film.

Technical specification

 Determines the altitude above ground level (AGL)

 Resolution: 0 cm

 Measures altitudes from -3000 m to 3000 m

 Dimensions: 23 x 5 x 6 mm

 max. Current Consumption: 0 mA

 Supply Voltage: 3.4 - 8.5 V

 Weight: less than 2.2 g (with cable ~3.0 g)

 Power supply via the X-BUS cable

 Can be used for drones, helicopters, sailplanes, planes, Jets,

rockets, HGL/DGL

rctool.de

Kay Claußen

Südliche Auffahrtsallee 8

80639 München

GERMANY

WEEE-Reg.-Nr.

DE 87908722

This product must not be disposed of with other

waste.

Instead, it has to be taken to a waste

collection center for treatment, recycling, or

disposal. For more information about where you

can drop off your waste equipment for recycling,

please contact your local city office, your

household waste disposal service or where you

purchased the product.

Altri manuali rc-tool Accessori

rc-tool

rc-tool Vario-DX Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente

rc-tool Alti-DX2 Manuale utente

Manuali Accessori popolari di altre marche