RCA DVR2080 Manuale utente

DVR2080/DVR2160

Digital Video

Recorder

User’s Guide

TOCOM 16395340

English/Français/Español

16395340_Cover 8/5/04, 5:28 PM1

Important Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICING PERSONNEL.

The lightning ash with arrowhead symbol, within an equilateral triangle,

is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufcient magni-

tude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

Caution: To prevent electric shock, match wide blade of plug to wide slot,

fully insert.

Product Registration

Please ll out the product registration card (packed separately) and return it immediately.

Returning the card allows us to contact you if needed.

Product Information

Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it

here and record the serial and model numbers in case you need them. These numbers are located

on the product.

Model No. _______________________________________________________________

Serial No. _______________________________________________________________

Purchase Date: ___________________________________________________________

Dealer/Address/Phone: _____________________________________________________

Cautions on Installation

Noise or disturbance of the picture may be generated if this unit or any other electronic

equipment using microprocessors is used near a tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV, but no further than 15 feet for

1394 cable.

• Set the antenna wires from the tuner or TV away from this unit’s power cord and input/

output connection cords.

• Noise or disturbance tends to occur particularly when using indoor antennas or 300 ohms

feeder wire. It is recommended that you use outdoor antennas and 75 ohm coaxial cables.

16395340_Cover 8/5/04, 5:28 PM2

Safety Information

Safety Instructions

1. Read Instructions – All the safety and operating instructions should be read before operating

this device.

2. Heed Warnings – All warnings on the device and in the User Manual should be adhered to.

3. Follow Instructions – All operating and user instructions should be followed.

4. Water and Moisture – The device should not be used near water – for example, near a bath-

tub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, and

the like.

5. Ventilation – The device should be situated so that its location or position does not interfere

with its proper ventilation. For example, the appliance should not be situated on a bed, sofa,

rug, or similar surface that may block the ventilation openings; or, placed on a built-in instal-

lation, such as a bookcase or cabinet that may impede the ow of air through the ventilation

openings.

6. Heat – The device should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including ampliers) that produce heat.

7. Power Sources – The device should be connected to a power supply only of the type de-

scribed in the operating instructions or as marked on the device.

8. Power-cord Protection – Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them, paying particular attention

to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

9. Non-use Periods – The power cord of the device should be unplugged from the outlet when

left unused for long periods of time.

10. Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not

spilled into the enclosure through the openings.

11. Damage Requiring Service – The device should be serviced by qualied service personnel

when:

a. The power-supply cord or the plug has been damaged; or

b. Objects have fallen, or liquid has been spilled into the enclosure; or

c. The device does not appear to operate normally or exhibits a marked change in perfor-

mance; or

d. The device has been dropped, or the enclosure damaged.

12. Servicing – The user should never attempt to service the device beyond that described in the

operating instructions. All other servicing should be referred to qualied service personnel.

16395340_00 8/5/04, 5:28 PM1

Table of Contents

Chapter 1: Overview and Setup

Introduction ........................................................................................................................3

Requirements ......................................................................................................................3

List of Contents ..........................................................................................................................3

Device Description..............................................................................................................3

DVR Front.................................................................................................................................... 3

DVR Back .....................................................................................................................................4

Things to Consider Before You Connect...........................................................................4

Ensure Proper Ventilation of the DVR......................................................................................4

IEEE-1394 Cables: 4-Pin and 6-Pin.........................................................................................5

Protect Against Power Surges ................................................................................................... 5

Connecting the DVR...........................................................................................................5

Connecting Other IEEE 1394 Devices ..............................................................................5

Component Connection Methods..............................................................................................6

Incorrect Hub Connection.......................................................................................................... 7

When Connecting Other IEEE 1394 Devices...........................................................................7

Adding IEEE 1394 Devices Automatically................................................................................7

DVR Device Conguration .................................................................................................7

Recording Device Setup .....................................................................................................8

DTVLink Recording...................................................................................................................... 9

Chapter 2: Using the DVR

Using the DVR................................................................................................................... 11

Controlling Live TV........................................................................................................................... 11

Pausing Live TV and Recorded Shows..................................................................................... 11

Transport Functions.................................................................................................................. 11

RECORD............................................................................................................................................. 11

STOP................................................................................................................................................... 11

Fast FORWARD and Fast REVERSE Playback ................................................................................12

PAUSE, Frame Advance, and Multi-speed Slow Motion..............................................................12

Instance Replay and Jump Ahead...................................................................................................13

Next and Previous Track..................................................................................................................13

Deleting Recorded Programs (Tracks).....................................................................................13

Status Bar..................................................................................................................................14

Program Information (TV's Channel Banner).........................................................................14

TV's Recordings Menu..............................................................................................................15

Chapter 3: Other Information

Troubleshooting ................................................................................................................16

Specications....................................................................................................................17

Limited Warranty .............................................................................................................18

Copy-Protected Materials ...............................................................................................19

Care and Cleaning ............................................................................................................19

FCC Declaration of Conformity.......................................................................................20

16395340_00 8/5/04, 5:28 PM2

Chapter 1: Overview & Setup

Illustrations contained in this document are for representation only.

Chapter 1 3

Introduction

The Digital Video Recorder, or DVR, is designed specically for recording and playback of High

Denition Television (HDTV). The DVR connects to a Digital Television (DTV) via DTVLink® (IEEE

1394) to offer control over digital video playback. Think of it as a “tape-less” digital VCR for

digital television. You can pause, fast forward, reverse, or use instant replay, so you’ll never miss

a moment. But unlike a traditional VCR where you wait for a program to nish recording before

you start watching it, the DVR allows you to “Pause Live TV.” This means you can pause, rewind,

and play back a digital program as it is being recorded without losing any of the recording.

Record all of your favorite digital programs while maintaining the same high quality digital

picture that it was broadcast in.

The DVR is sometimes referred to as an Audio Video Hard Drive (AVHD).

Requirements

Digital Television with at least one IEEE 1394 jack and support of Audio/Video commands (AV/C)

List of Contents

• DVR Unit

• A/C Power Cord

• IEEE 1394 Cable

• User's Guide

Device Description

DVR Front

The front of the DVR has a clean professional look to coincide with your other high-end audio/

video equipment. It has backlit text display to indicate the status of the unit.

• POWER – illuminated when the unit is plugged in to an AC power source.

• PLAY – illuminated when a previously recorded program is being played back.

• RECORD – illuminated while a new program is being recorded for future playback.

Note: The DVR can record and play back different programs at the same time or can play back the program currently

being recorded. During these instances, both the RECORD and PLAY lights are illuminated.

DTVLink® Certication Logo is a U.S. registered mark of CEA.

16395340_1 8/5/04, 5:28 PM3

Overview & Setup

4 Chapter 1

Illustrations contained in this document are for representation only.

Overview & Setup

Chapter 1 5

Illustrations contained in this document are for representation only.

DVR Back

The back of the DVR has two 6-pin DTVLink® or IEEE 1394 ports and an A/C power cord connector.

Devices using IEEE 1394 interface can be connected to either port. Devices certied as DTVLink

use the same IEEE 1394 interface but also include advanced copy protection schemes to send and

receive encrypted or copy protected content.

Things to Consider Before You Connect

Ensure Proper Ventilation of the DVR:

• Leave at least 4 inches (10 cm) of space between the top and back of the DVR and a wall,

shelf, or other component.

• Leave at least 1” (2.5 cm) of space on the front and sides.

• Do not block ventilation holes on any of the components.

• Arrange the components so that air can circulate freely.

• Do not stack components on top of the DVR.

• When you place components in a stand, make sure you allow adequate ventilation.

• If you connect an audio receiver or amplier, place it on the top shelf so the heated air from

it won’t ow around other components.

DVR Top View

DVR Front View

Note: The DVR uses an internal fan to ensure proper

cooling of the electrical circuits and the AV hard drive.

Upon startup, the fan will briey run at 100% and then

quickly slow down to the minimal speed required to cool

the unit.

DTVLink (1394) Ports AC Power Cord Connector

16395340_1 8/5/04, 5:28 PM4

Overview & Setup

4 Chapter 1

Illustrations contained in this document are for representation only.

Overview & Setup

Chapter 1 5

Illustrations contained in this document are for representation only.

IEEE-1394 Cables: 4-Pin and 6-Pin

There are two different types of connectors used on IEEE 1394

devices: a 4-pin connector, and a 6-pin connector.

The 4-pin connector is capable of sending digital audio signals,

digital video signals and digital control signals back and forth

between devices. The 6-pin connector is capable of sending the

same data and signal information as the 4-pin but has two

To connect the DVR to a DTVLink enabled TV, follow these steps:

1. Connect the female end of the AC power cord to the DVR and male end into an AC outlet

or surge protector.

2. Connect the 1394 cable to any DTVLink port on the HDTV and to either DTVLink port on

the DVR.

INPUT 1

RS-VIDEO

CABLE

INPUT

ETHERNET G-LINK

DIGITAL

AUDIO

OUTPUT

AUDIO/VIDEO

OUTPUT

CableCARD™

COMPOSITE INPUTS

INPUT 2

ANTENNA INPUT

COMPONENT/COMPOSITE INPUTS

Use menu for composite video.

RPRPB

Y/VIDEO

HDMI/DVI INPUT

Use menu for DVI audio.

POWER

(AC 120V~60Hz)

FIXED/VARIABLE AUDIO OUTPUTS

EXTERNAL AMP

MAX POWER RATING!

(60 WATTS into 8 OHMS)

CENTER SPEAKER INPUT

SUBWOOFER

CENTER R REAR L REAR

MATRIX

SURROUND

OUTPUTS

WIRED

INPUT 3

RS-VIDEO

INPUT 4

Y/VIDEO

additional pins for sending low voltage electrical power. The purpose of this electrical power is to

provide the needed operating power to a device that is not connected directly to the household

AC power such as some camcorders. The DVR uses 6-pin IEEE 1394 connectors but does not supply

power to other devices. To connect other devices, such as a digital camcorder, that uses a 4-pin

connector, you need to obtain a 4-pin to 6-pin adapter cable. These cables are available from

electronic and computer stores.

Note: When the DVR is connected to an RCA HDTV, the HDTV does not supply power to the DVR. The DVR must be

plugged into a source of power (wall outlet).

Protect Against Power Surges

• Connect all components before you plug any power cords into the wall outlet.

• Turn off the TV and/or component before you connect or disconnect any cables.

• Make sure all antennas and cables are properly grounded.

Connecting the DVR

16395340_1 8/5/04, 5:28 PM5

Overview & Setup

6 Chapter 1

Illustrations contained in this document are for representation only.

Overview & Setup

Chapter 1 7

Illustrations contained in this document are for representation only.

Connecting Other IEEE 1394 Devices

One of the great advantages to 1394 components is the ability to connect one device to the next

in a single chain. This is known as “daisy-chaining.” Previous audio and video components often

required connections of each component to a single source such as an audio/video receiver or TV.

With IEEE 1394, simply connect one device to the next in a continuous chain using 1394 cables.

The 1394 interface reduces the number of cables needed to connect each device and simplies

the connection process. There is no need to ensure that you are connecting the correct audio or

video cable to the correct jack. IEEE 1394 devices use a single cable to transfer audio, video, and

interface data between all devices connected within the chain.

The DVR has two 1394 ports. This allows you to use one port for connection to your digital

television and still have another port for connection of additional 1394 components. Each

compatible DTVLink device connected on the IEEE 1394 chain is shown on the TV. Information can

be sent between 1394 connected components. DTVLink and other compatible components can be

controlled from your TV.

Component Connection Methods

There are two ways to connect IEEE 1394 and DTVLink devices: component-to-component and

hub connection. The component-to-component method has each component connected in a

chain-like fashion, with the DTV as the rst component. The hub method is basically the same but

uses both 1394 jacks on the DTV with two chains of components connected to it.

Note: Use a single 1394 cable to connect one device to any available 1394 port on the next device. If devices such as a

digital camera only have one 1394 port, these devices should be placed at the end of the 1394 chain.

16395340_1 8/5/04, 5:28 PM6

Overview & Setup

6 Chapter 1

Illustrations contained in this document are for representation only.

Overview & Setup

Chapter 1 7

Illustrations contained in this document are for representation only.

Incorrect Hub Connection

Some IEEE 1394 devices have more than two ports. These devices can act as a hub allowing you

to branch out the 1394 chain. This provides increased exibility in the device location and cable

routing of additional 1394 devices. Ensure that you do not connect to a device already in the

1394 chain. There should be only one path between any two devices.

When Connecting Other IEEE 1394 Devices

• No two 1394 components should have more than one connection path between them. Do

not loop the last device in the chain back to the TV. If the component chain is connected in a

loop, the TV may not be able to work with any of the other devices.

• Place devices that have only a mechanical (two-position) power switch at the end of the

chain or leave the power switch in the ON position. When turned OFF, IEEE 1394 signals may

not be able to pass through the device to other devices.

• If a device only has one 1394 port, place it at the end of the 1394 chain.

• Place the slower components at the end of the chain and the faster ones closest to the TV in

the chain for faster communication speed. See component's guide for 1394 network speed.

• Do not use an IEEE 1394 cable longer than 15 feet between each device or from device to the

TV.

Adding IEEE 1394 Devices Automatically

When an IEEE 1394 device is connected into the TV network and is powered ON, the new device

may automatically be recognized by the TV. This is called “device discovery” and can take up to

1 minute. Some non-audio/video or non-compatible IEEE 1394 devices, such as Personal

Computers (PCs), may not announce their presence to the TV. The TV does not show these devices

in the input list, however, they may still be available to other devices on the IEEE 1394 network

that are compatible with these non-audio/video devices.

DVR Device Conguration

Once connected, the following outlines how to congure and use the DVR with some RCA HDTVs.

If you are using the DVR with other DTVLink enabled televisions, consult your TV Owner’s Manual

for Audio/Video Hard Drive (AVHD) conguration and use.

Don't Loop Connections

16395340_1 8/5/04, 5:28 PM7

Overview & Setup

8 Chapter 1

Illustrations contained in this document are for representation only.

Overview & Setup

Chapter 1 9

Illustrations contained in this document are for representation only.

Channel Search





�



�

 



�



























Recording Device Setup

To record digital content to the DVR, you may need to set up the Recording Device screen from

the TV’s Connections menu. Use the MENU button on the TV's remote control to access the

Connections menu and set up the DVR as a preferred recording device through the DTVLink (1394)

connection.

1. Press TV button on the TV remote to put the remote into TV mode.

2. Press MENU on the TV’s Remote control.

3. Use the Down Arrow to highlight Connections and press OK or right arrow (4) on the

remote.

4. Highlight DTVLink Setup and press OK or right arrow (4) on the remote.

5. Highlight Recording Device and press OK or right arrow (4) on the remote.

Note: The “DTVLink Connect” menu is for recognizing and conguring some DTVLink devices, that require an

additional analog connection, and does not pertain to the DVR.

The Recording Device screen conveys to the TV which DTVLink component is capable of receiving

transport commands (e.g., Record, Play, etc.) when a DTVLink component is not currently being

tuned. With this screen, you can select the default DTVLink recorder and the functionality level

for a DTVLink recording device. When the DVR is connected and powered on, it appears at the

top of the screen. If you have more than one DTVLink recording device, you may need to highlight

the Recording Device eld at the top of the screen. Press OK to scroll through the DTVLink

components and select the DVR you would like to be the default recording device for digital.

16395340_1 8/5/04, 5:28 PM8

Altri manuali per DVR2080

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali RCA Registratore digitale

RCA

RCA RTD315W Manuale utente

RCA

RCA DVR10 Manuale utente

Manuali Registratore digitale popolari di altre marche

FLIR

FLIR M3100E Series Manuale utente

VTRACKPRO

VTRACKPRO FPRO300 Manuale utente

Swann

Swann NVR-7085 models Manuale utente

XtendLan

XtendLan DVR-1670C Manuale utente

urmet domus

urmet domus 1093/004AHD Manuale utente

Holux

Holux M1 Manuale utente

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuale utente

Whistler

Whistler D16VRS Manuale utente

Defender Security

Defender Security 82-20235 Manuale utente

MISUMI

MISUMI MP-WF100M Manuale utente

Speco

Speco D8HU Manuale utente

UST

UST DDR-E04AA Istruzioni per l’uso

Consolidated

Consolidated Digital Video Recorder Manuale utente

Mace

Mace DVR0404RW Guida rapida

FSM

FSM Colibri Grande PRO Manuale utente

Hauppauge

Hauppauge HD PVR 2 Manuale utente

Identivision

Identivision ICR-PH161i PIONEER Manuale utente

DIGIFUSION

DIGIFUSION FVRT150 Manuale utente