1
In addition to the careful attention devoted to quality standards in the
manufacture of your product, safety is a major factor in the design of
every product. However, safety is your responsibility too. The following
important information will help to assure your enjoyment and proper
use of the product and accessory equipment. Please read them carefully
before operating and using your product.
Installation
1 Read and Follow Instructions—All the safety and
operating instructions should be read before the product
is operated. Follow all operating instructions.
2 Retain Instructions—The safety and operating
instructions should be retained for future reference.
3 Heed Warnings—Comply with all warnings on the product and in
the operating instructions.
4 Polarization/Grounding—This product is equipped with either a
polarized, non-polarized, or a grounding type power cord plug. If
equipped with the non-polarized type (two blades of identical size),
the following does not apply.
• A polarized power plug (two blades, one wider than the other)
will fit into a power receptacle only one way. This is a safety
feature. Do not defeat it. If you are unable to insert the plug fully,
try reversing it, or have an electrician change the receptacle. If
you need an extension cord, use only a polarized extension cord.
• A grounding type power plug (two blades and a round pin) will fit
only into a grounding type receptacle with matching openings. This
is a safety feature. Do not defeat it. You may need an electrician to
install a grounding type receptacle. If you need an extension cord,
use only a grounding type extension cord.
5 Power Sources—This product should be operated only from the type
of power source indicated on the product’s marking label. If you are
not sure of the type of power supply to your home, consult your
dealer or local power company. For products intended to operate from
battery power, or other sources, refer to the operating instructions.
6 Overloading—Do not overload wall outlets or extension
cords as this can result in a risk of fire or electric shock.
Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation, and broken
plugs are dangerous. They may result in a shock or fire
hazard. Periodically examine the cord, and if its appearance
indicates damage or deteriorated insulation, have it replaced by your
service technician.
7 Power-Cord Protection—Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them. Pay particular attention to cords where they
are attached to plugs, convenience receptacles and at the point
where they exit from the product.
8 Ventilation—Slots and openings in the enclosure are provided for
ventilation to ensure reliable operation of the product and to protect it
from overheating. These openings must not be blocked or covered. These
openings should never be blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product should never be placed near
or over a radiator or heat register, or another heat source (including
amplifiers). This product should not be placed in a built-in installation
such as a bookcase or equipment rack unless proper ventilation is
provided or the product manufacturer’s instructions have been followed.
9 Attachments—Do not use attachments unless recommended by the
product manufacturer as they may cause hazards.
10 Water and Moisture—Do not use this product near water—for
example, near a bath tub, wash bowl, kitchen sink or laundry tub, in
a wet basement, or near a swimming pool and the like.
11 Accessories—Do not place this product on an unstable surface or
support. The product may fall, causing serious injury to a child or
adult as well as serious damage to the product. Any mounting of the
product should follow the manufacturer’s instructions and use only a
mounting accessory recommended by the manufacturer.
11A A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause
the product and cart combination to overturn.
12 Outdoor Antenna Grounding—If an outside antenna or cable
system is connected to the product, be sure the antenna or cable
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National
Electrical Code, ANSI/NFPA No. 70-1984 provides information
with respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna-discharge
unit, size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for the
grounding electrode. See following example.
Example of Antenna Grounding
13 Power Lines—An outside antenna system should not be located in the
vicinity of overhead power lines, other electric light or power circuits,
or where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep from
touching or approaching such power lines or circuits as contact with
them might be fatal. Installing an outdoor antenna can be hazardous
and should be left to a professional antenna installer.
Use
14 Cleaning—Unplug this product from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
15 Object and Liquid Entry—Never push objects of any kind into this
product through openings as they may touch dangerous voltage or
“short-out” parts that could result in a fire or electric shock. Never
spill liquid of any kind on the product.
16 Lightning—For added protection for this product
during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the product due to lightning and
power line surges.
Service
17 Servicing—Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
18 Conditions Requiring Service—Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions.
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled, or objects have fallen into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions. Improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product
to its normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. When the product exhibits a distinct change in performance,
such as the inability to perform basic functions—this indicates a
need for service.
19 Replacement Parts—When replacement parts are required, have the
service technician verify that the replacement parts he uses have the
same safety characteristics as the original parts. Use of replacements
specified by the product manufacturer can prevent fire, electric
shock, or other hazards.
20 Safety Check—Upon completion of any service or repairs to
this product, ask the service technician to perform safety checks
recommended by the manufacturer to determine that the product is
in safe operating condition.
IMPORTANT SAFETY INSTRUCTIONS
ANTENNA
LEAD IN
WIRE
GROUND CLAMP
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
ELECTRIC SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
