RDZ WHR 60 Manuale utente

Air Handling Units

Unità Trattamento Aria

WHR 60

TECHNICAL/INSTALLATION MANUAL

MANUALE TECNICO/INSTALLAZIONE

Mechanical ventilation with heat recovery appliance

Ventilazione meccanica con sistema di recupero di calore

9100547.00

01/2017

bit.ly/rdzwebsite

22

INTRODUCTION

This manual includes technical descriptions, installation instructions, assembly, maintenance and

technical data exclusively directed to qualified personnel involved in the installation and

maintenance of the product.

INTENDED USE

The product is artistically made and installed to allow a constant air exchange inside the room. The

recovery system can be generally installed in residential or public places.

The product is supplied with a ceramic heat exchanger that accumulates heat during the

extraction of hot air coming from the room while, during the air intake from the outside, the

device transfers to the inlet cold air, the thermal energy stored in the heat exchanger.

The product is designed for wall installation. The duct containing the heat exchanger is supplied

for walls with a maximum thickness of 400mm; the duct can be shorten to a minimum of 250mm.

The extracted or incoming air must not contain inflammable or explosive mixtures, chemical

vapors, dusts, oils and other pathogenic substances in general.

23

CONTENT

1- Cosmetic Frontal Cover 7- Ceramic heat exchanger

2- Shutter 8- Filters

3- Unit 9- installing and maintenance manual

4i- Internal wall-mounting part with electrical

connections

10- Precautions

11- RAEE warranty paper

4e- External wall-mounting part 12- Packaging

5- External conveyor 13- Warnings for proper unpackaging

6- Recessed duct 400mm

24

TECHNICAL PARAMETERS

The Heat Recovery System is categorized as a Class II product.

The protection level is IPX4.

The Heat Recovery System is projected for indoors installation. Working temperature is included

between -20°C and 50°C with maximum relative humidity of 80%.

The design of the Heat Recovery System is in continuous evolution, therefore, some models may

differ from those described in this manual.

DIMENSIONS, MM

-WHR 60

Speed 12345

Voltage at 50Hz 220-240Vac 220-240Vac 220-240Vac X X

Power Ø150 [W] 4,9 6,9 8,9 X X

Power Ø100 [W] 3,9 5,9 7,9 X X

Flow rate Ø150 [m³/h] 30 45 60 X X

Flow rate Ø100 [m³/h] 15 22,5 30 X X

Noise at 3 m Ø150 [dB] 13 20 23 X X

Noise at 3 m Ø100 [dB] 19 24 29 X X

Max efficency 93% 93% 93% X X

25

CONSTRUCTION

The product is composed of a wall mounted unit to be placed inside the room, a recessed duct

which contains the ceramic heat exchanger and filters and an external wall mounted conveyor.

Ceramic heat

conveyor

External wall

mounted conveyor

Recessed duct External flter

Internal filter

Wall mounted

unit

INSTALLATION

Installation must only be carried out by properly qualified person.

Make sure that the main electrical supply in the installation room is disconnected before starting

the electrical operations of assembly.

The appliance must not be installed near curtains, drapes, etc. as these could compromise the

correct working of the product.

Make sure that, once installed, the fan blades are placed not less than 2,30m away from the floor

below to the product.

Before assembling or using this product, carefully read all the instructions in this manual and be

sure to own all the necessary material for the installation.

Scrupulously follow the instructions in this manual.

1) ASSEMBLY

Once the area of installation is selected, mark the center of the hole to be realized on the wall

Make sure that on internal and external walls there is enough space, for a radius of 15 cm from

the center, thus corresponding to the product overall dimensions. Therefore make sure that,

within this area, there are not any interferences with other walls or non-removable objects.

Hole diameter for installation is Ø160mm

The duct must be installed through the hole, with a slight downward slope of 1° - 2° towards the

outsight to allow proper discharge of condensation.

To use the supplied recessed duct, the thickness of the wall must not exceed 400mm.

26

To install the product, the wall thickness cannot be less than 250mm.

Once obtained the hole, put the recessed duct (6) into the wall.

Make sure that the length of the recessed duct (6) is equal to the thickness of the wall.

The duct must end with the internal and external surfaces of the wall.

The quote “M” cannot be less than 250mm. In this case the wall is not appropriate to install the

product.

Adapt the duct if necessary, to the thickness of the wall with suitable tools, in the best way as

shown below:

27

Once adapted the length of the recessed duct (6) to the exact thickness of the wall, put the

external wall- mounting part (4e) on the external wall as shown in the picture below:

Insert the centering diameter of the wall-

mounting part (4e) inside the recessed duct

(6).

Once centered in the duct, mark the fixing holes on the external wall using the external wall-

mounting part (4e) through a level measure tool to ensure a proper installation as shown in the

picture below:

Make the holes and insert the expansion plug for the wall mounting.

Fix the external wall-mounting part (4e) on the external wall.

28

Fix the external conveyor (5) on the external wall mounting part (4e) till the complete assembly, as

shown in the pictures below:

2) ELECTRICAL CONNECTIONS

Installation must only be carried out by qualified person. Make sure that the voltage of the

installation room is in compliance with the value declared on the product label.

Make sure that the main electrical supply in the installation room is disconnected before electrical

assembly operations.

Identify the version of the product and carefully read all the instructions related to electrical

connections.

As done by marking the external holes, insert the centering diameter of the internal wall-mounting

part (4i) within the recessed duct (6) as shown in the picture above.

By using a measure level tool, mark and make four holes to fix on the wall the internal wall-

mounting part (4i).

29

Unlike the external wall mounting part, on the internal wall is necessary to bring the power supply

conductors to connect them to the stripped wires supplied with the product.

Provide an output for the wires, as the highlighted area shown in the picture

.

Once the expansion plugs for the wall mounting are inserted, carefully check all the electrical

operation before proceeding with the installation.

Indice

Manuali Unità di trattamento dell'aria popolari di altre marche

Klimor

Klimor EVO-S Manuale utente

Salda

Salda SMARTY XP Guida

BLAUBERG

BLAUBERG KOMFORT Roto EC S400 Manuale utente

Trenton

Trenton TPLP Series Manuale utente

Kemper

Kemper CleanAirTower Manuale utente

Daikin

Daikin DV PTC 14 Series Manuale utente

Haier

Haier HB2400VA1M20 Manuale utente

Webasto

Webasto BlueCool A-Series Manuale utente

Carrier

Carrier 39T Dimensioni e guida di installazione

Armstrong Air

Armstrong Air BCE5V Series Manuale utente

ActronAir

ActronAir CAY500T Manuale utente

Carrier

Carrier 40MBDAQ Manuale utente

Allied

Allied A93UH1E Manuale utente

Nortek

Nortek B6VMAI Manuale utente

TemperZone

TemperZone Econex Pro OPA 1410RLTM4FPQD Guida alla manutenzione e all'assistenza

AAON

AAON H3 Series Manuale del proprietario

Lennox

Lennox VEOA042N432U Istruzioni per l'installazione

Salda

Salda RIRS 400VE EKO 3.0 Manuale utente