RealFlame C9630LP Manuale utente
If the information in this manual
is not followed exactly, a fire or
explosion may result causing
property damage personal injury
or loss of life.
Improper Installation, adjustment,
alteration, service or maintenance
can cause injury or property
damage.
Read the installation, operation
and maintenance instructions
thoroughly before installing or
servicing this equipment.
!
!
IMPORTANT
WARNING
SAVE THESE INSTRUCTIONS
!DANGER
If you smell gas:
2. Extinguish any open flame.
3. If odor continues, keep away from the appliance and
immediately call your gas supplier or fire department.
C SU
For Technical Support Please Contact Real Flame® At: 1-800-654-1704
C9630LP Ventura Fire Table NG Conversion Kit
1. Shut o gas to the appliance.
PARTS LIST 00023102G
1
2
3
NATURAL GAS CONVERSION KIT
NOTE
This conversion kit is for changing a Liquefied Petroleum (LP) fire table into a Natural Gas
fire table.
!
This conversion kit shall be installed by a qualified service agency in accordance with
Real Flame’s instructions and all applicable codes and requirements of the Authority
Having Jurisdiction. If the information in these instructions is not followed exactly, a fire,
explosion or production of carbon monoxide may result causing property damage,
personal injury or loss of life. The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and complete until the operation of
the converted appliance is checked as specified in the manufacturer’s instructions
supplied with this kit.
WARNING
!
Natural Gas Hose and Quick Disconnect
NG Orifice Spud #2.43mm
Primary Air Mixer Sleeve
4
4
5
Conversion Plaque
Cable Kit
3
1
2
5
1
C9630LP Ventura
Conversion
3
NATURAL GAS CONVERSION
2
1.) Remove access door.
2.) Disconnect and remove propane tank.
NATURAL GAS CONVERSION
3
3.) Disconnect LP hose from valve.
4.) Disconnect bellows (CSST) from burner base.
Bellows
4
NATURAL GAS CONVERSION
5.) Remove the existing LP orifice spud.
LP Orifice Spud
LP Orifice Spud
LP Orifice Spud
LP Orifice Spud
5
NATURAL GAS CONVERSION
6.) Locate the new NG orifice spud, verify it is the correct number.
The number 2.43 should be on the end of the orifice spud.
7.) Slip sleeve over primary air opening. See fig. 1
Next, screw the new NG orifice spud into the burner base. See fig. 2
Sleeve
Primary Air
Opening NG Orifice
Spud
1
2
2.43
6
NATURAL GAS CONVERSION
8.) Re-attach bellows (CSST) to new spud.
9.) Attach NG hose to the input side of the valve.
Bellows
7
10.) Attach quick disconnect to gas supply.
NATURAL GASCONVERSION
House Natural Gas Piping
Quick Disconnect Socket
NG Gas Hose
To Fire Table
11.) After installing the conversion kit, verify the location of the
Thermocouple and Igniter Pin using the illustration below.
Installing at Altitude
For installations at elevations above 2000 ft. contact your local dealerorgas
supplier before installing as input rating should be reduced approximately 4%
for each 1000 ft. above sea level. Refer to the National Fuel Gas Code.
Contact the Real Flame for more information at 1-800-654-1704
12.) Note to installation technicians. Verify the manifold pressure by using a
3/8” flared T-junction at the location marked by the arrow below. Then using
a digital manometer verify that the pressure before the orifice is 7” W.C. Also
verify that the orifice spud has the 2.43 marked. This will allow you to verify
that the input rating of the appliance is correct.
NATURAL GAS CONVERSION
8
Igniter
Thermocouple
To Manometer
14.) Cut the exis
French plaque and NG conversion plaque included with this kit to the fire table using
the included cable kit.
Cut Cable Re-attach both plaques
NOTE: The proper manifold pressure for this converted appliance is 7” water column.
NOTE: The maximum inlet gas pressure for this unit is 10.5 in wc (2.61 kPa)
The minimum inlet gas pressure for this unit is 3.5 in wc (0.87 kPa)
NATURAL GAS CONVERSION
WARNING Before using this outdoor fire table, make sure you have read, understand and
are following all information provided in the important Safety Information section of this
manual. Failure to follow those instructions can cause death, serious injury or property damage.
!
Check for leaks at these locations
13. CHECKING FOR LEAKS
Make a leak check solution by mixing 1 part dishwashing soap
with 3 parts water in a spray bottle.
Make sure the control knob is “OFF.”Then, turn the Natural Gas on
at its source.
Spray leak solution on the valve connections, paying particular
attention to the areas indicated by the arrows.
nect and re-test. If you continue to see bubbles after several
attempts, disconnect the Natural Gas Source and Contact Real
Flame® at 1-800-654-1704 for assistance.
If no bubbles appear after one minute turn the gas
source “OFF”, wipe away solution and proceed.
9
Altri manuali per C9630LP
1
Indice
Lingue:
Altri manuali RealFlame Accessori per caminetti
RealFlame
RealFlame 8022E Manuale utente
RealFlame
RealFlame R0001-BK Manuale utente
RealFlame
RealFlame Chateau 5950 Manuale utente
RealFlame
RealFlame 8240 Manuale utente
RealFlame
RealFlame C11810 Manuale utente
RealFlame
RealFlame 13058E Manuale utente
RealFlame
RealFlame 561 Manuale utente
RealFlame
RealFlame C820LP Manuale utente
RealFlame
RealFlame Crawford 8020E Manuale utente
RealFlame
RealFlame 310 Manuale del prodotto
RealFlame
RealFlame 817919/C0005LP Manuale utente
RealFlame
RealFlame 7770E Manuale utente
RealFlame
RealFlame C1600 Manuale utente
RealFlame
RealFlame 13053E Manuale utente
RealFlame
RealFlame 8140E Manuale utente
RealFlame
RealFlame C1510LP Manuale utente
RealFlame
RealFlame 1680LP Manuale utente
RealFlame
RealFlame Sedona 11815 Manuale utente
RealFlame
RealFlame 7760E Manuale utente
RealFlame
RealFlame C1460LP Manuale utente
