Regency Heatwave P36 Manuale utente

918-225c 11/19/09

Manufactured by:

FPIFireplaceProductsInternationalLtd.

6988 Venture St.,

Delta, B.C. Canada, V4G 1H4

Tested by: Warnock Hersey

FOR YOUR SAFETY

What to do if you smell gas:

* Do not try to light any appliance

* Do not touch any electrical switch: do not

use any phone in your building.

* Immediately call your gas supplier from a

neighbour'sphone.Followthegassupplier's

instructions.

* If you cannot reach your gas supplier, call

the ﬁre department.

WARNING:

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage. Refer

to this manual. For assistance or additional information

consult an authorized installer, service agency or the gas

supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other ﬂammable vapours

and liquids in the vicinity of this or any other appliance.

Installation and service must be performed by an author-

ized installer, service agency or the gas supplier.

HEAT WAVE DUCT KIT

PLEASE KEEP THESE INSTRUCTIONS

FOR FUTURE REFERENCE

KIT # 946-568

Approved for use with Models:

P36, P36D, P42, P48, P90, P95, L676S, P33S & HZ54

www.regency-ﬁre.com

2Regency Heat Wave Air Duct Kit

Diagram 1: Guide for possible air duct runs and locations. Keep duct length and number of

bends to a miniumum. Maximum duct length is 20 ft. (6.1m) per kit.

LISTINGS AND CODE

APPROVALS

This Kit has been approved for use with Model

P36, P36D, P42, P48, P90, P95, L676S, P33S

&HZ54.Thiskithas beentestedin accordance

with National Safety Standards, and has been

certiﬁedbyWarnockHerseyforinstallation and

operation in the United States and Canada as

described in these Installation and Operating

Instructions.

Check with your local building code agency

before you begin your installation to ensure

compliance with local codes, including the

need for "permits" and follow-up inspections. If

any problems are encountered regarding code

approvals, or if you wish clariﬁcation on any of

the instructions contained here, contact your

local dealer.

GENERAL

INFORMATION

The Heat Wave Air Duct Kit increases the ef-

fectivenessofyourﬁreplacebydispersingwarm

air from the ﬁreplace to remote locations in the

same room or other rooms in your home.

Up to two kits may be installed on the ﬁreplace.

Please Note: Only 1 HeatWave kit may be

operated at one time. This includes the internal

blower option as well.

IMPORTANT

INSTALLATION NOTES

1) Theapplianceinstallationmustconformwith

localcodesor,intheabsenceoflocalcodes,

with the current Canadian or National Gas

Codes, CAN1-B149 orANSI Z223.1 Instal-

lation Codes.

2) Theappliancewheninstalled,mustbeelec-

trically grounded in accordance with local

codes, or in the absence of local codes with

the current National Electrical Code, ANSI/

NFPA70 or CSAC22.1 Canadian Electrical

Code.

3) This kit is tested and safe when installed

inaccordancewiththisinstallationmanual.

Please read all instructions before starting

installation and follow all instructions care-

fully during installation.

4) Installationofthiskitmustbeperformedby

a qualiﬁed service technician.

5) The Heat Wave Kit must be installed only

as speciﬁed.Any modiﬁcations of the kit or

componentswillvoidthewarrantyandmay

cause a ﬁre hazard.

6) Plan the location of the ﬁreplace and the

warm air duct runs, see diagram 1 as a

guide for possible duct runs and locations.

Maximum Duct Run: 20 ft. (6.1m) per

kit.

NOTE: Airﬂow through the duct system is

affected by the duct length and number of

bends. Keep the length and bends to a

minimum to maximize performance.

PARTS

Included with Kit:

1 946-010 20 ft. (6.1 m) of 6" dia. ﬂex pipe

1 946-517 Fan housing assembly

1 910-423 Variable wall rheostat

1 946-006 Air register

1 946-005 Register adaptor frame (thick)

1 946-000 Round Duct collar

1 946-001 Oval Duct collar

1 946-002 Duct adaptor (round to oval)

1 946-045 Insulation (60")

Hardware package

Ifanypartsaremissingordamaged,contact

your dealer before starting installation. DO

NOT install a damaged kit.

Regency Heat Wave Air Duct Kit

MINIMUM FRAMING CLEARANCES

12”

(305mm)

12”

(305mm)

20” (508mm)

P33 / P36 / P36D / P48

14”

(356mm)

14”

(356mm)

26-1/4”

(667mm)

P48

Minimum Duct Clearances

Theairducthasa'0'clearancetocombustiblesbuttheﬁrst24"ofpipefrom

the unit requires insulation (included with kit). See diagram 4 on page 3.

*Wall studs must be 16" on center for mounting fan housing.

* Fan Housing: Maintain a 1/4" (6mm) clearance from fan housing to combustible material.

* Wall Registers must be 4"(102mm) from ﬂoor above or ceiling below.

6-1/2"

(165mm)

6-1/2"

(165mm)

- 20” (508mm)

- 21-1/4” (533mm)

P90

P95

P90 / P95 - Top Exit

14"

(356mm)

14"

(356mm)

- 20” (508mm)

- 21-1/4” (533mm)

- 22” (559mm)

P90

P95

HZ54

P90 / P95 / HZ54 - Side Exit

4Regency Heat Wave Air Duct Kit

Diagram 2 Side View: Secure fan housing

to minimum 2 x 4 framing.

INSTALLATION

Remove the 2 screws holding the cover plate

on the ﬁreplace side.

NOTE:InstallationofHeatWaveductkitshould

be done prior to drywall installation.

A) P36, P36D, P42, P48, P90, P95 & HZ54

models:

1) Remove the cover plate from the ﬁreplace

side and discard.

Tab

Front View

2) Remove the knock-out and bend the tabs

outward.

Center Round

Duct collar over

hole and attach

to the tabs using

3 screws

NOTE:Thismustbedonepriortoplacing

ﬁreplace into ﬁnal position.

Knockout

plate

2) Bend the tabs outward.

Tab

Tabs

Round Duct Collar

pushed down to

inner shell

A) P90 / P95 Model:

1) Remove the knockout plate from the ﬁre-

place top and discard.

3) Cutoutandremovetheinsulationunderthe

top opening.

4) Push Round Duct Collar through to inner

shelltopandattachtoall3tabsonﬁreplace

top with screws.

B) All models:

1) Determinethe locationoftheairregister/fan

housing assembly. Cut a 5" x 16" (121mm

x 406mm) hole between framing members

(wall studs or ﬂoor joists). Maintain a 1/4"

(6mm) clearance from fan housing to com-

bustiblematerial.Seepage2forclearances.

2) Mountandsecurethefanhousingassembly

to framing members, the front of the fan

housing will protrude 1/2" (51mm) out of

the wall so it may be ﬁnished with drywall,

etc. See diagram 2.

Regency Heat Wave Air Duct Kit

Diagram 4

Diagram 3: P90 model

Diagram 3: P36, P36D, P42 & P48 models

3) Install the air duct run. The air duct run has

a zero clearance to combustibles construc-

tionbut the ﬁrst 24" of the pipe from theunit

requiresinsulation(includedwithkit).Check

local codes.

Securetheducttotheductcollarontheunit

and to the fan housing with 3 screws (per

end) and aluminum duct tape (UL 181A-P

or equivalent).

The ﬁrst 24" of duct pipe (from the unit)

must be covered with insulation.

Round Air Duct: Attach the 6" round air

duct (supplied) to the ﬁreplace collar and

run the duct to the fan housing. Attach the

round-to-oval adaptor to the fan housing

and the air duct to the adaptor, diagram 3.

Oval Air Duct: Attach the round-to-oval

adaptor to the ﬁreplace starting collar and

a 6" oval duct (not supplied) to the adaptor.

Complete the duct run and attach the oval

duct to the fan housing.

Round and Oval Duct: A combination of

6" round and 6" oval duct can be used in

the duct run. Oval duct components are

not supplied but can be purchased from an

HVAC supplier.

4) InstallthevariablespeedWallRheostat(with

OFF setting) in a convenient location. This

switch controls the fan operation.

5) Wire 120VAC service to the Wall Rheostat

andfromtheWallRheostattotheFanJunc-

tion Box. Use wire nuts to secure the 120V

AC wires to the hot and neutral fan wires

and screw the 120V AC ground wire to the

FanJunctionBox.Seewiringdiagrambelow.

6) Screw the fan junction box to the fan hous-

ing.

7) Screw the RegisterAdapter Frame and the

AirRegisterto the Fan Housing,diagram 4.

Note: For new construction only the Air

Registerisrequiredtocovertheopening.

8) Complete the ﬁreplace installation as per

ﬁreplace installation manual.

6Regency Heat Wave Air Duct Kit

Ground Lug

CAUTION: Label all wires prior

to disconnection when servic-

ing controls. Wiring errors can

cause improper and dangerous

operation.

Caution: Ensure that the wires do

not touch any hot surfaces and are

away from sharp edges.

NOTE: The wires (in dotted lines) and

wire nuts are supplied by others.

IMPORTANT: If the internal blower is installed, it cannot

be operated if the Heat Wave air duct kit fan is operating.

OPERATION

1) Start the ﬁreplace as per instructions and allow it to warm up.

2) Turn the Wall Rheostat "ON" and adjust the variable speed based

upon desired air ﬂow at the Air Duct Register.

WIRING DIAGRAM

MAINTENANCE

1) Service and maintain the ﬁreplace as per the ﬁreplace installation

manual.

2) Keep the Air Register(s) clean and free of any blockage.

Do not cut the ground terminal off

under any circumstances.

Regency Heat Wave Air Duct Kit

NOTES

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Regency Accessori per caminetti

Regency

Regency HEAT WAVE 946-556 Manuale utente

Manuali Accessori per caminetti popolari di altre marche

Valor

Valor L2 1700K Manuale utente

Exodraft

Exodraft Xzense Manuale utente

Whalen

Whalen Ruso MNFP62BF23-6 Manuale utente

Lopi

Lopi Hearthview 864 Manuale utente

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuale utente

EdilKamin

EdilKamin SERBATOIO 250 Guida rapida

Bronpi

Bronpi KIT-1 Manuale utente

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuale utente

Travis Industries

Travis Industries 33 DVI Manuale utente

Superior

Superior ASD3628-TI Manuale utente

pleasant hearth

pleasant hearth OFP28WG Manuale utente

IHP

IHP Astria Series Manuale utente

Firegear

Firegear FG-H-2110SS Manuale utente

Nibe

Nibe Contura C i31 Manuale utente

kozy heat

kozy heat KZK-052 Manuale utente

SimpliFire

SimpliFire SF-WM36 Manuale utente

Bluegrass Living

Bluegrass Living BC18NR Guida rapida

pleasant hearth

pleasant hearth IRIS SCROLL Manuale utente