Rehabmart SmartMount SA740P Guida

Max UL Load Capacity: 80 lb (36.3 kg)

3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

ISSUED: 05-18-05 SHEET #: 095-9234-10 08-23-07

Installation and Assembly:

SmartMount™ Articulating LCD Wall Arm

Models: SA740P, SA740P-S, RTFPA-220, RTFPA-220I, RTFPA-220S,

RTFPA-220SI, 902220

Features:

•Fits 22" - 40" LCD screens

• Threetensionablepivotpointsforextensiveadjustmentofviewingangle

• VESA®75/100/200 x 100/200 x 200 compatible

• Frees up space by folding flat against the wall

• Keeps electronic wires routed internal to reduce clutter

This product is intended for use with UL

Listed products and must be installed by a

qualified professional installer.

2 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Note: Read entire instruction sheet before you start installation and assembly.

Forcustomercare call (800) 729-0307 or (708) 865-8870.

Table of Contents

Parts List.............................................................................................................................................................................. 3

Installation to Wood Stud Wall ............................................................................................................................................. 4

Installationto Solid Concrete and CinderBlock .................................................................................................................... 5

Tools Needed for Assembly

• studfinder ("edge to edge" stud finder is recommended)

• phillipsscrewdriver

• 3/16"allenwrench

• drill with 1/4" and 5/32" drill bits

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call

Peerless customer service at 1-800-729-0307.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never mount this product to a metal stud wall construction unless the stud can be verified to be constructed of 25

gauge steel minimum, the drywall is 1/2" thick minimum and you obtain and use the Peerless accessory kit for metal

studs.

• NeverexceedtheMaximumULLoadCapacity.

• If mounting to wood wall stud wall construction, make sure that mounting screws are anchored into the center of the

studs. Use of an "edge to edge" stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power. See suggested torque values where applicable within these instructions.

WARNING

Accessories

• Metal Stud Wall Plate (WSP models) (Not evaluated by UL)

3 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

RTFPA-220S

RTFPA-220 SA740P-S

SA740P RTFPA-220I 902220 RTFPA-220S

Description Qty. Part # Part # Part # Part #

Awall mount 1 095-0376 095-0376 095-0378 095-0378

BAlligator® anchor 2 590-0097 590-0097 590-0097 590-0097

.198" ID x .313" OD x .437" H retaining spacer

4 590-5005 590-5005 590-5003 590-5003

D1/4-20 x 1/2" flat head phillips screw 2 520-1209 520-1209 520-2178 520-2178

EM4 x .7 x 10 mm phillips screw 4 504-9012 504-9012 520-2027 520-2027

FM4 x .7 x 20 mm phillips screw 4 504-9020 504-9020 504-2014 504-2014

GM6 x 1 x 12 mm phillips screw 4 520-1128 520-1128 520-2039 520-2039

H#14 x 2-1/2" flat head wood screw 2 520-1202 520-1202 520-2165 520-2165

IM6 x 1 x 20 mm phillips screw 4 520-9402 520-9402 520-2040 520-2040

JM6 x 1 x 30 mm phillips screw 4 510-9109 510-9109 520-2042 520-2042

KM5 x 1 x 6 mm phillips screw 5 520-1023 520-1023 520-2214 520-2214

L#10 flat washer 4 540-9400 540-9400 540-9442 540-9442

Mhook bracket 1 095-1346 095-1346 095-4346 095-4346

Nadapter plate 1 095-1322 095-1322 095-4322 095-4322

O#10-32 x 1/4" flat head phillips screw 1 520-1108 520-1108 520-2108 520-2108

Pinstallation kit (not shown) 1 n/a 200-8570 n/a 200-8570

Parts List

CFG

4 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Installation to Wood Stud Wall

Remove cord covers from wall arm assembly (A) as shown in figure 1.1. Using a stud finder, locate and mark the

edges of the wood stud used in mounting this product. Use of an edge to edge stud finder is highly recommended.

Use a level to draw a vertical line down the center of the stud. Use wall plate as template to mark center of holes

along the vertical line. Drill two 5/32" (4 mm) dia. holes 2.5" (65 mm) deep.Attach wall mount (A) to wall using two

#14 x 2.5" flat head wood screws (H) as shown in figure 1.2.

Skip to step 2 on page 6.

• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhardwareand

components.

WARNING

• Tightenscrews so that wall plate is firmly attached, butdo not overtighten. Overtightening can damage the screws,

greatlyreducingtheir holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the studs. The use of an "edge to edge" stud finder is

highlyrecommended.

WARNING

WOOD

STUD

WALL

fig. 1.2

CORDCOVER

Afig. 1.1

5 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Installation to Solid Concrete and Cinder Block

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meetASTM C-90 specifications.

It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid

breakingoutthe back of the hole when entering avoidor cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Makesure that the supporting surface will safely support thecombined load of the equipment and all attached hard-

wareand components.

WARNING

Removecord covers from wall arm assembly (A)as

shown in figure 1.1. Level and use wall plate as

template to mark center of holes. Drill two 1/4" (6

mm) dia. hole to a minimum depth of 2" (51 mm).

Insert anchors (B) in holes flush with wall as shown

in fig 1.3. Place wall mount (A) over anchor and

secure with wood screw (H) as shown in figures 1.4

and 1.6. Make sure wall mount is level, and tighten

all fasteners. See figure 1.5.

Skip to step 2 on next page.

• Concrete anchors are notintended for attachment to

concretewallcoveredwith a layer of plaster, drywall,

orotherfinishingmaterialasshownbelow.Ifmounting

toconcretewallcovered with plaster/drywall is

unavoidable,plaster/drywall(up to 5/8" thick) must be

counterboredasshownbelow.Besureconcrete

anchorsdonotpull away from concrete when tighten-

ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer

(notevaluated by UL).

WARNING

concrete

wall

Drill holes

and insert

anchors.

Place wall

plate over

anchor and

secure with

screw.

Tighten all

fasteners.

WALLPLATE

fig. 1.3

fig. 1.4

fig. 1.5

CUTAWAYVIEW

CORRECT

concrete

plaster/

drywall

INCORRECT

concrete

plaster/

drywall

• Tighten screws so that wall plate is firmly attached,

butdonot overtighten. Overtightening candamagethe

screws,greatlyreducingtheirholdingpower.

• Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

Afig. 1.6

WALLPLATE

6 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Attaching Adapter Plate to Screen with VESA 200 x 100 or 200 x 200 Mounting

Pattern

Attach hook bracket (M) to adapter plate (N) using

four M5 x 6 mm screws (K) and #10 washers (L) as

shown.

FORVESA200x100MOUNTINGPATTERN:

Choosehole patternasshown below.Attachadapter

plate (N) to back of screen using four M4 x 10 mm

screws(E)as shownbelow.

*Note: If screw (E) gets less than three threads of

engagement, attach adapterplate (N) to back of

screen using four M4 x 20 mm screws (F) and four

spacers(C)asindicatedbelow.

Skip to step 3 on page 9.

FORVESA200x200MOUNTINGPATTERN:

Choosehole patternasshown below.Attachadapter

plate (N) to back of screen using four M6 x 12 mm

screws(G)as shownbelow.

*Note: If screw (G) gets less than three threads of

engagement, attach adapterplate (N) to back of

screen using four M6 x 20 mm screws (I). If screw (I)

still gets less than three threads of engagement, use

four M6 x 30 mm screws (J).

Skip to step 3 on page 9.

*For screens with a hole

pattern in a pocket,

spacers (C) go between

adapter plate (N) and

screen.

Note: For VESA 75 mm and 100 mm patterns, see

followingpage.

2-1

• If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not

tightly secured, damage may occur to screen or product may fail.

WARNING

7 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Attaching Hook Bracket to Screen with VESA 75 or 100 Mounting Pattern

*For screens with a hole

pattern in a pocket,

spacers (C) go between

hook bracket (M) and

screen.

FORVESA®75MOUNTINGPATTERN:

Choosehole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10 mm

screws(E)as shownbelow.

*Note: If hole pattern is in a pocket, attach hook

bracket (M) to back of screen using four M4 x 20 mm

screws(F)and four retaining spacers (C)asindicated

below.

Skip to step 3 on page 9.

FORVESA100MOUNTINGPATTERN:

Choosehole pattern as shown below. Attach hook

bracket (M) to back of screen using four M4 x 10 mm

screws(E)as shownbelow.

Skip to step 3 on page 9.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

8 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

GENERICADAPTER

BRACKET

FOR INSTALLING TO PEERLESS LC MODEL ADAPTER BRACKET

For screen compatibility please refer to the LCD or plasma interface list on our website

www.peerlessmounts.com or call customer care for a screen specific adapter bracket LC or PLP models (not

ULevaluated).

FOR INSTALLING TO PEERLESS PLP MODEL ADAPTER BRACKET

GENERICADAPTER

BRACKET

M5X6MMOR M5 X 10MMSCREW

M5X10MMSCREW

Note: Referto LC model adapter bracket instruction sheetfor attachment of adapter bracket to screen.

Note: Either M5 x 6 mm or M5 x 10 mm screws are included with the LC model adapter bracket.

Attach hook bracket (M) to adapter bracket using four M5 x 6 mm or M5 x 10 mm screws.

Skip to step 3 on page 9.

Note: Refer to PLP model adapter bracket instruction sheet for attachment of adapter bracket to screen.

Note: M5 x 10 mm screws are included with the PLP model adapter bracket.

Attach hook bracket (M) to adapter bracket using four M5 x 10 mm screws.

9 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

Adjust tension knob on side of mount shown in figure

4.1 to desired tension to balance your screen size

andweight.

Push or pull from top or bottom of screen to adjust

tilt as shown. The tilt can be adjusted to a maximum

of15°forwardor5°backward.

• Becarefulnottopinchfingerswhenopeningand

closing mount from the wall.

CAUTION

• Do not tighten screws with excessive force.

Overtighteningcancause damage to mount. Tighten

screws to 40 in. • lb (4.5 N.M.) maximum torque.

CAUTION

TENSIONKNOB

fig. 4.1

To attach screen to wall mount (A), lower hook

bracket (M) with screen at an angle into pockets of

wall mount as shown in figure 3.1. Once clips are

engaged, push down to seat clips in pockets as

shown in figure 3.2. Insert and tighten M5 phillips

screw (K) to lock screen to wall mount as shown in

figure3.3.

Toremove screen from mount, loosenscrew(K) and

lift screen off of mount.

Installing and Removing Flat Panel Screen

4-1 Roll screen to desired position (5° clockwise or

counter-clockwise).Insert #10-32 x 1/4"flat head

phillips screw (O) to lock screen into position as

shownin figure 4.2.

fig. 4.2

SCREEN

fig. 3.1 fig. 3.2

fig. 3.3

• Do not tighten screws with excessive force.

Overtighteningcancause damage to mount. Tighten

screws to 20 in. • lb (2.26 N.M.) maximum torque.

CAUTION

• Do not lift more weight than you can handle. Use

additionalmanpoweror mechanical lifting equipment

to safely handle placement of the screen.

• Failure to lock hook bracket (M) with screw (K) can

cause screen to come off mount if hit accidentally.

WARNING POCKET

CLIP

10 of 30 ISSUED: 07-12-06 SHEET #: 095-9234-10 08-23-07

If more or less tension is desired in the arm pivot points, do the following:

• To increase tension, turn tension screw(s) clockwise with allen wrench.

• To reduce tension, turn tension screw(s) counter-clockwise with allen wrench.Do not turn more than half a turn.

• Do not remove screw or loosen screw until it is no longer engaged with the mount. Doing so may cause the

screen to fall.

WARNING

Note: Makesurecords have enough slack to allow full movementofthe arm.

Route cords inside arm slots of wall mount (A) as shown in figure 5.1. Optional: Run power cord through one side of

mountandsignalcable(s)throughother side in order to avoid interference with the signal.

Lock cords into place by sliding cord covers onto mount as shown in figure 5.2. Screen may have to be moved for

better access for sliding on the cord covers.

fig. 5.1

fig. 5.2

CORDCOVER

TENSIONSCREWS

Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Rehabmart Supporto TV

Rehabmart

Rehabmart Paramount PF650 Guida

Manuali Supporto TV popolari di altre marche

Ergotron

Ergotron Neo Flex Cantilever UHD Manuale utente

StarTech.com

StarTech.com FPCEILBTB Manuale utente

VonHaus

VonHaus 05/038 Manuale utente

Techlink

Techlink ECHO TV Manuale utente

Sandstrom

Sandstrom SSTVMC12X Manuale utente

Sony

Sony SU-WL700 Guida

ICW

ICW SCACC18 Manuale utente

LG WM-L640V Manuale utente

Gembird

Gembird WM-65ST-01 Manuale utente

ERARD

ERARD FiTUP XXL 035320 Manuale utente

PEERLESS

PEERLESS PLCK-1 Guida

Kanto

Kanto RCF180 Manuale utente

GEM

GEM GEM GP001 Manuale utente

Gladiator Joe

Gladiator Joe GJ0A0053 Manuale utente

Vivotek

Vivotek AM-105 Manuale utente

Vivo

Vivo VESA STAND-VAD1B Manuale utente

AmazonBasics

AmazonBasics B07QG3LMG4 Manuale utente

Secura

Secura QLF210 Manuale utente