Reliable 6000FS Manuale utente
8” STRAIGHT KNIFE INSTRUCTION MANUAL
6000FS
1
6000FS
INSTRUCTION MANUAL
2
RELIABLE. RIGHT THERE WITH YOU.
At Reliable, we do what we love, and take pride in doing it right.
You want what’s best for the people, places and things that matter
in your life – from where you live to what you wear. So do we. From
the start, we approach every product with a craftsman’s attention
to detail and passion for making it right. Quality, functionality,
design and customer service play an equally important part in
delivering what’s right for you. The 6000FS is your best choice for
cuts that are up to 8” in height. It’s designed with a low center of
gravity for ease of handling and features the best power to weight
ratio in the industry.
For your safety and to fully enjoy the advantages of this product,
please take a few minutes to read all the important safeguards
and care instructions. Keep this manual handy and review the
product warranty for your reference.
3
IMPORTANT SAFETY REQUIREMENTS
Before operating the motor, be sure that the electrical supply voltage and current are
the same as stamped on the label. Fill the oil cup. Push in the turning knob and turn the
machine over a few revolutions by hand to see if the knife moves easily.
MACHINE CARE
1. Clean lint out of sharpener twice a week.
2. Remove cover over cam and clean out lint around screw mechanism in sharpener once
a week.
3. Remove knife and clean slides with slot cleaner once a day.
4. To prevent accumulation of lint, do not oil plate rollers.
5. If rollers stick, remove rollers from the plate and wash them with a cleaning solvent.
WARNING
This machine is equipped with a sharp
knife. Keep hands away from the knife area
at all times. When operating or handling the
machine, be sure to only use control levers
and handles. Do not operate sharpener
without the knife in the machine or the
sharpener will become damaged.
SHARPENING THE KNIFE
Take the machine out of the lay. Drop the
pressure foot lever, using the pressure
foot lever located next to the machine’s
operating handle. Press the release lever
downward slowly, with firm pressure to
engage the sharpening mechanism. If lever
locks, lift latch lever and restart.
To change the knife blade, press in the
turning knob and position the blade to its
lowest point. Insert the blade removal tool
and loosen the knife lock-bolt. Remove the
blade through the bottom of the knife slot.
Insert a new blade into the knife slot and
tighten the knife lock-bolt.
4
PART NO.
DE1
DE2
DE3
DE4
DE5
DE6
DE7
DE8
NO. REQ’D
3
2
4
1
1
4
4
1
DESCRIPTION
SHARPENER HOLD-DOWN NUT
SHARPENER HOLD-DOWN NUT
FRONT-TO-REAR BEARING NUT
PLATE BOLD NUT
STANDARD-BEARING SCREW
FRONT-REAR-BEARING SCREW
SCREW
KNIFE
5
PART NO.
DE9
DE10
DE11
DE12
DE13
DE14
DE15
DE16
DE17
DE18
DE19
DE20
DE21
DE22
DE23
DE24
DE25
DE26
DE27
DE28
DE29
DE30
DE31
DE32
DE33
DE34
DE35
NO. REQ’D
1
1
1
1
4
1
2
2
1
1
1
2
1
1
1
1
2
2
1
1
1
1
1
1
2
1
1
DESCRIPTION
TERMINAL WIRE TUBING
STATOR WITH BAND
ROTOR AND SHAFT
CARRYING HANDLE
SCREW
TERMINAL WIRE TUBING
REAR BALL BEARING
TERMINAL
REAR BEARING HOUSE
TERMINAL BLOCK
ATTACHMENT PLUG
SCREW
CUTOUT SWITCH MOUNT
AUTOMATIC CUTOUT
AUTOMATIC CUTOUT SWITCH
SHAFT COVER FOR CUTOUT
SCREW
SCREW
COVER FOR CUTOUT
ROTOR FAN
LEADING SPING WASHER
CLUTCH NUT
RETAINING RING
FAN COVER
SCREW
CLUTCH SPING
TURNING KNOB
6
7
PART NO.
DE36
DE37
DE38
DE39
DE40
DE41
DE42
NO. REQ’D
6
1
1
1
1
1
1
DESCRIPTION
SCREW
SCREW
CAPACITOR COVER
CAPACITOR
COVER FOR CAPACITOR
SPRING FOR CAPACITOR
SHAFT LOCK NUT
PART NO.
DE43
DE44
DE45
DE46
DE47
DE48
DE49
DE50
DE51
DE52
DE53
DE54
DE55
DE56
DE57
DE58
DE59
DE60
DE61
DE62
DE63
DE64
DE65
DE66
DE67
DE68
DE69
DE70
DE71
DE72
DE73
DE74
DE75
DE76
DE77
DE78
DE79
DE80
DE81
DE82
DE83
DE84
DE85
DE86
DE87
DE88
DE89
DE90
NO. REQ’D
1
1
1
4
3
9
3
1
2
1
1
3
1
1
1
1
1
2
1
1
1
1
1
1
1
6
1
1
2
1
1
1
1
1
1
1
3
1
1
1
1
3
4
2
2
1
1
1
DESCRIPTION
FRONT BEARING HOUSING
BEARING
FRONT BALL BEARING RETAINER
SCREW
SCREW
WASHER
NUT
CRANK
STUD, UPPER
STUD, LOWER MOUNTING
STUD, LOWER MOUNTING
GUIDE ADJUSTMENT NUT
SHAFT FOR BALL BEARING
SEATED FOR BALL BEARING
LOCK NUT FOR SHAFT
CRANK BALL BEARING LOCK NUT
CONNECTING ROD
SCREW
H.GUIDE
CROSS HEAD
WRIST PIN
WRIST PIN FELT PAD
CONNECTING ROD WASHER
SCREW
GUIDE WASHER
SCREW
KNIFE LOCK WASHER
SCREW
SCREW
HANDLE BRACKET
SCREW
SCREW FOR HANDLE BRACKET
OPERATING HANDLE LOCK NUT
OPERATING HANDLE
SWITCH
SWITCH BASE
SCREW
OILING DEVICE
OIL TUBE
EYELET
COVER OIL TUBE
LONG WICHKING
SCREW
SCREW
CIRCLE
WINDOWS FOR OIL
OIL TUBE COVER
OIL HOLE COVER
7
8
9
PART NO.
DE91
DE92
DE93
DE94
DE95
DE96
DE97
DE98
DE99
DE100
DE101
DE102
DE103
DE104
DE105
NO. REQ’D
1
1
2
2
2
3
1
1
4
4
4
12
2
2
2
DESCRIPTION
STANDARD
KNIFE SLIDE
THROAT PLATES
TAPER PIN
SCREW
SCREW
PLATE WING
PLATE
RUBBER ROLLER ALL SET
ROLLER SHELL
RUBBER MOUNTED ROLLER
CLAMP SCREW FOR ROLLER
HINGE PIN
PLATE WING SPRING
LOCK WASHER #8
Indice
Altri manuali Reliable Accessori
