Remington 500V Manuale utente
IMPORTANT:
Read this manual and all labels carefully before operat-
ing your powder actuated tool. This manual should
always accompany the tool and be transferred with it
upon change of ownership.
Operating
Instructions
POWDER ACTUATED TOOL
MANUFACTURERS´ INSTITUTE INC.
™
G 029
®
A
N
I
N
D
E
P
E
N
D
E
N
T
L
A
B
O
R
A
T
O
R
Y
T
E
S
T
I
N
G
F
O
R
P
U
B
L
I
C
S
A
F
E
T
Y
G 028
®
Power Pro™
Semi-automatic
Model 500V
482-1
2
106763
INDEX
Warning: Safety Precautions............................................................ 3-11
Why A Power Fastener Holds ............................................................. 12
Selecting Power Fasteners and Power Loads .................................... 13
Operation ....................................................................................... 14-15
Parts List ........................................................................................ 16-17
Cleaning and Maintenance ................................................................. 17
Tool Disassembly ........................................................................... 18-21
Tool Assembly................................................................................ 22-25
Troubleshooting Guide ........................................................................ 26
Replacement Parts and Accessories .................................................. 27
Technical Service ................................................................................ 27
Repair Service..................................................................................... 27
Parts Centrals ..................................................................................... 28
Fasteners ............................................................................................ 28
Application Chart ................................................................................. 29
Warranty................................................................................ Back Cover
Power Fastener*
Recommended
Approved
Goggles
Muzzle/
Guide
Barrel
Assembly
Trigger
Maximum 3" Spall
Shield
REMINGTON®
Power Pro™ Semi-automatic Model 500V
The Remington®Power Pro™ Model 500V is designed for use with
Remington®.27 caliber power load strips and Remington®power
fasteners which are no longer than 3". Remington®power fasteners
are manufactured from special steel and heat treated to produce a
very hard yet ductile fastener.
10-Shot
Power Load
Strip*
*Not supplied with tool
Power
Indicator
Adjustment
Wheel
3
106763
G 018
Warning: Safety Precautions
IMPORTANT: Read these operating instructions carefully and com-
pletely before trying to operate or service this tool. Improper use of
this tool can cause serious injury or death from firing fastener into
body or from flying debris. We expressly disclaim any liability for any
injury to persons or damage to property which result from your failure
to take the precautions contained in this manual.
WARNING: This tool is designed only for use by qualified operators.
Qualification is obtained through a thorough understanding of the Safety
Warnings and operating instructions as defined in this operating manual.
NOTE: The labor regulations of many states require that the operator of this
tool on a job site be thoroughly trained and certified for competence prior
to operating this tool. For certification procedures, call: DESA Specialty
Products™ Technical Services Department, 1-800-858-8501 or visit
www.desatech.com (U.S.A.) or 1-905-826-8010 (Canada).
1. ALWAYShandle thetool as if it wereloaded. Before starting work, checkthat the tool
is unloaded and the muzzle is clear. NEVER load a tool unless it is going to be used.
2. ALWAYS inspect to make sure the tool is working properly. If the tool does not
work properly, remove from service and tag “DEFECTIVE.” DO NOT use the
tool again until it has been properly repaired.
3. Operators and bystanders must ALWAYS wear goggles and hearing protection
which meet or exceed the accepted standards for adequate protection in your
country. In the USA, refer to ANSI standards. In Canada, refer to CSA standards.
BEFORE USING
DEFECTIVE
Continued
4
106763
G 018
Safety Precautions
POWDER
ACTUATED
TOOLS
IN USE
WARNING
!
4. ALWAYS clear the work area on all sides and post appropriate warning signs
on job sites.
1. NEVER place your hand over the muzzle. Accidental discharge can cause
serious injury.
HANDLING THE TOOL
2. NEVERplace yourfinger on the trigger untilthe tool’smuzzle is against the work
surface.
5. ALWAYS make sure the work area is clean from loose material and debris.
G 018
G 018
5
106763
G 018
G 018
Safety Precautions
4. NEVER carry or pass a loaded powder actuated tool. NEVER point a powder
actuated tool at anyone.
3. ALWAYS store UNLOADED powder actuated tool and power loads in a locked
container. Keep power loads of different power levels in separate containers.
5. If the tool is dropped, inspect for damage and repair it before continuing to work.
NEVER use a damaged tool.
6. ALWAYS take precaution to maintain your balance while operating a powder
actuated tool.
POWDER
LOADS
POWD
LOAD
G 018
G 018
Continued
6
106763
TOO HARD
Point
flattens
TOO SOFT
Sinks in
with
average
hammer
blow
?
?
?
TOO BRITTLE
Surface
shatters
G 018
G 018
G 018
Safety Precautions
7. An operator taking medication should take extra precautions while handling the
tool. NEVER drink alcoholic beverages or take medications which impair your
vision, balance or judgement before using a powder actuated tool.
KNOW YOUR FASTENING BASE MATERIAL
?
?
?
?
CENTER
PUNCH TEST
1. ALWAYS know the thickness and type of base material into which you are
fastening. NEVER GUESS. Test the base material by using the Center Punch
Test. The Center Punch Test is performed by using a hammer to test drive the
particular power fastener to be used into the material. If the point penetrates
easily, the material is too soft. If the point becomes blunt, the material is too
hard. If the material fractures, cracks or shatters, the material is too brittle. Test
fastenings can be made if the material shows a clear fastener impression and
the fastener point is not blunted. ALWAYS use test fastenings to determine the
correctpower load level and thetool’s powerindicator setting (see
PowerLoads
and Power Indicator Setting,
page 13). Operators and bystanders must always
wear goggles and ear protection which meet or exceed the accepted standards
for adequate protection in your country. In the USA, refer to ANSI standards.
In Canada, refer to CSA standards.
G 018
7
106763
CAST IRON GLASS
TILE BRICK
482-33
G 018
G 018
G 018
G 018
Safety Precautions
3. NEVER make fastenings in spalled or cracked areas.
2. NEVER attempt to drive power fasteners into very hard or brittle materials
including, but not limited to cast iron, glass, tile, stone, brick, or hardened steel.
Materials of this type tend to shatter and create hazards from flying particles.
4. NEVER drive power fasteners into thin or easily penetrated materials unless it
is backed by concrete or steel. When in doubt, such as when base material is
concealed, conduct a Center Punch Test (See page 6). Check continually to
avoid fastening into unsuitable material, especially in older buildings.
5. DO NOT fasten through or within 1/2" of predrilled or pre-punched holes.
G 018
Continued
8
106763
TOO THIN
WELD
G 018
3/16" MIN
1/2"
1"
Safety Precautions
7. DO NOT drive power fasteners into steel base material less then 3/16" thick,
within 2" of a weld, within 1/2" of the edge or within 1" of another power fastener.
3" 3"
3"
6. DO NOT drive power fasteners into concrete less than three times as thick as
the intended fastener penetration, within 3" of the edge, within 3" of another
power fastener or within 3" of a failed power fastener.
3"
3X
1X
8. When fastening into masonry walls, always drive into horizontal mortar joints,
never into vertical mortar joints. BE CAREFUL. A poorly laid joint may permit
too much penetration, and/or unsatisfactory holding power.
G 018
OPERATING THE TOOL
1. ALWAYS hold tool perpendicular to work surface.
9
106763
POWER
LOADS
POWER
LOADS
GASOLINE
GAS
OLINE
G 018
G 018
G 018
G 018
G 018
Safety Precautions
2. Should the tool fail to fire, hold the muzzle firmly against the work surface for 30
seconds. Release the trigger and remove pressure on the tool while holding the
muzzle against the work surface. Again press the tool firmly against the work
surface and pull the trigger. If the tool still fails to fire, hold the tool firmly against
the work surface for another 30 seconds before advancing the power load strip.
Use remaining loads in strip. Discard power load strip into water or oil.
WATER
3. ALWAYS use the spall shield when driving directly into concrete or steel.
Always wear goggles.
4. NEVER use a powder actuated tool in an explosive or flammable atmosphere
or when non-sparking tools are required.
POWER LOADS AND FASTENERS
1. NEVER leave unfired power load strips on floors or work surfaces.
Spall
Shield
Continued
10
106763
G 018
POWER
LOADS
ONLY
Safety Precautions
1
2
3
4
56789
10
11
12
1
22
L
E
K
C
I
N
B
R
A
S
S
C
A
L
I
B
E
R
NOTE:
Failure to start with
thelowestpowerlevel
canresultin overdrive
condition and will re-
sult in damage to tool
(See page 13).
2. Remington®power load strips are available in three power levels – green (level
3), yellow (level 4) and red (level 5). Green is lowest power level, red is highest
power level. Always use test fastenings to determine the correct power load
level and the tool’s power indicator setting (see
Power Loads and Power
Indicator Setting,
page 13).
IMPORTANT:
Purple (level 6) power load strips
will not function in model 500V tool.
Start
YELLOW
POWER
LEVEL 4
GREEN
POWER
LEVEL 3
RED
POWER
LEVEL 5
G 018G 018
3. NEVER use power loads in firearms.
5. A color blind person must take extra precautions to prevent the chance of
mixing the power load strips of various levels.
4. NEVER carry fasteners or other hard objects in the same pocket or container
with power load strips.
POWER
LOAD
STRIPS
ONLY
27
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Remington Utensili elettrici
