Repotec RP_3000EX_ML Manuale utente
PCI Express Gigabit Ethernet Adapter
User’s Manual 1
Preface
This manual describes how to install and use the PCI Express
Gigabit Ethernet Adapter. This PCI Express Gigabit Ethernet
Adapter allows options of the RJ-45 or different fiber connections
(such as connector types and segment distance).
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
•Introduction on PCI Express Gigabit Ethernet Adapter
•Product features
•LEDs functions
•Hardware installation
•Software installation
•Specifications
PCI Express Gigabit Ethernet Adapter
2 User’s Manual
Table of Contents
PREFACE 1
TABLE OF CONTENTS 2
PRODUCT OVERVIEW 3
PACKAGE CONTENTS 3
PRODUCT FEATURES 4
Driver Support 5
LEDs 5
HARDWARE INSTALLATION 6
INSTALLING ETHERNET ADAPTER INTO PCI EXPRESS SLOT 6
CONNECTING TO YOUR NETWORK 7
PCI Express Gigabit Ethernet Adapter 7
PCI Express Fiber Gigabit Ethernet Adapter 7
Cabling Requirements 9
DRIVER INSTALLATION 10
DIAGNOSTICS UTILITY 13
DIAGNOSTICS UTILITY INSTALLATION 13
DIAGNOSTICS UTILITY CONFIGURATION 15
General 15
VLAN 16
Driver 16
Advanced Setting 17
Diagnostics 17
Send and Receive 17
Statistics 18
Cable 18
Wake On LAN 19
SPECIFICATIONS 20
PCI Express Gigabit Ethernet Adapter
User’s Manual 3
Product Overview
Package Contents
When you unpack the product package, you shall find the items
listed below. Please inspect the contents, and report any apparent
damage or missing items immediately to our authorized reseller.
3PCI Express Gigabit Ethernet Adapter
3User’s Manual
3Software Driver
PCI Express Gigabit Ethernet Adapter
4 User’s Manual
Product Features
zProvide
One 10/100/1000Base-TX port, or
One 1000Base-SX/LX port
zRJ-45 connection:
Auto-negotiate 10/100/1000Mbps and full/half duplex
Auto MDI/MDIX
Compliant with IEEE 802.3 10Base-T, IEEE 802.3u
100Base-TX, IEEE 802.3ab 1000Base-T
zFiber connections:
SC connector for multi-mode and single-mode
Compliant with IEEE 802.3z 1000Base-SX/LX
zPCI Express 1.0a compliant
zSupports Microsoft NDIS5 Checksum Offload (IP, TCP,
UDP) and Largesend Offload
zAdvanced Configuration Power Management Interface
(ACPI) 2.0
z10/100/1000Base-TX port supports Wake-on-LAN remote
wake-up
zSupports IEEE802.1Q VLAN Tagging
zSupports IEEE802.1p Layer 2 Priority Encoding
zRFC 1157 SNMP v1 compliant
zPreboot Execution Environment (PXE) 2.1
zCable diagnostic utility
zSupports Jumbo Frame up to 7K (Vista) and 4K (XP and
other OS)
zSupports PCI Message Signaled Interrupt (MSI)
zIEEE 802.3x full duplex flow control
z48K Bytes buffer memory
zTwo LEDs: LNK (link) (Green), ACT (activity) (Yellow)
z0℃to 45℃(32℉to 113℉) operating temperature range
PCI Express Gigabit Ethernet Adapter
User’s Manual 5
Driver Support
The Adapter supports a wide range of drivers for commonly used
network operating systems:
yMirosoft Windows 98SE, ME, 2000, XP (32/64-bit), 2003,
Vista (32/64-bit)
yFreeBSD 5.4, 6.0
yLinux driver for kernel 2.4.x, 2.6.x (Support x86, x64)
yMacOS 10.4, 10.5 on Intel-based Mac computer
yNDIS2 driver for DOS (Support MSclient, Lantastic, Lanman,
Norton Ghost)
yNovell client for DOS (ODI driver)
yNovell Netware Server driver (Support OS 4.x, 5.x, 6.x)
yPXE ROM code
ySCO Open Server 6.0
ySCO Unix 5.0.6, 5.0.7
ySetup diagnostic program (DOS program)
yUnix Ware 7.1.3, 7.1.4
LEDs
yLNK Link
yACT Activity
LEDs Status Indication
Steady A valid network connection established.
LNK stands for LINK.
LNK
(Green) Off No network connection.
Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
ACT
(Yellow) Off No activity.
PCI Express Gigabit Ethernet Adapter
6 User’s Manual
Hardware Installation
Installing Ethernet Adapter into PCI Express
slot
Step 1: Turn off the power to the PC.
Step 2: Remove any metal decorations from your hands and wrists.
Step 3: Remove the cover from your PC.
Step 4: Locate an empty bus mastering PCI Express slot and remove the
corresponding backplate. Save the screw for use in Step 6.
Step 5: Carefully insert the PCI Express Gigabit Ethernet Adapter into the chosen
slot and press firmly with proper push to ensure it is fully seated in the
slot.
Step 6: Secure the PCI Express Gigabit Ethernet Adapter with the screw you
saved in step 4.
Step 7: Replace the PC cover.
Step 8: Proceed to “Connecting to Your Network” section.
PCI Express Gigabit Ethernet Adapter
User’s Manual 7
Connecting to Your Network
PCI Express Gigabit Ethernet Adapter
This section describes how to connect the PCI Express Gigabit
Ethernet Adapter to a network.
<Note>
You must connect the PCI Express Gigabit Ethernet Adapter to the network before
installing the network driver.
Step 1: Prepare a network cable with corresponding connectors for the two end
devices, one end to the PCI Express Gigabit Ethernet Adapter and the
other to a network switch.
Step 2: When the cable is properly connected to the devices, turn on the power to
the PC.
Step 3: Check the LNK (Link) LED. The LED will come on when the PCI
Express Gigabit Ethernet Adapter is receiving a good link signal from the
connected device, a switch.
Step 4: Proceed to next section for installing the network driver.
PCI Express Fiber Gigabit Ethernet Adapter
This section describes how to connect the PCI Express Fiber
Gigabit Ethernet Adapter to a 1000 Mbps fiber-based Ethernet
network, which contributes to its optimal performance.
<Note>
You must connect the PCI Express Fiber Gigabit Ethernet Adapter to the network
before installing the network driver.
Step 1: Remove the protective covers from the PCI Express Fiber Gigabit
Ethernet Adapter’s connector.
Step 2: Prepare a network cable with corresponding connectors for the two end
devices, one end to the PCI Express Fiber Gigabit Ethernet Adapter and
the other to a 1000Mbps fiber port on the network switch.
PCI Express Gigabit Ethernet Adapter
8 User’s Manual
Step 3: Connect the network cable to the connector on the PCI Express Fiber
Gigabit Ethernet Adapter. This network cable consists of two individual
cables: one for ‘transmission (TX)’, and the other for ‘reception (RX)’.
Step 4: Connect the other end of the network cable to a 1000BASE-SX/LX
switch.
<Note>
i. Insert the cable that is connected to the transmit (TX) connector on the PCI Express
Fiber Gigabit Ethernet Adapter into the receive (RX) connector on the network switch.
ii. Insert the cable that is connected to the receive (RX) connector on the PCI Express
Fiber Gigabit Ethernet Adapter into the transmit (TX) connector on the network switch.
Step 5: When the cable is properly connected to two end devices, turn on the
power to the PC.
Step 6: Check the LNK (Link) LED. The LED will come on when the PCI
Express Fiber Gigabit Ethernet Adapter is receiving a good link signal
from the connected device, a switch.
Step 7: Proceed to next section for installing the network driver.
PCI Express Gigabit Ethernet Adapter
User’s Manual 9
Cabling Requirements
For connector type, cabling requirements, and maximum segment
distance when connecting the PCI Express Gigabit Ethernet
Adapter to your network, please refer to the following table.
Speed Connector Port Speed
Half/Full
Duplex
Cable Distance
10Base-T RJ-45 10/20 Mbps Category 3,
4, or 5
UTP/STP
100
meters
100Base-TX RJ-45 100/200
Mbps Category 5
UTP/STP 100
meters
1000Base-T RJ-45 2000 Mbps Category 5
or 5e
UTP/STP
100
meters
Connector Type
on Fiber Adapter Wavelength of 850nm
Fiber Optic required Maximum Distance
(* full-duplex)
SC Multi-mode, 62/125 µm 550 m
Connector Type
on Fiber Adapter Wavelength of 1310nm
Fiber Optic required Maximum Distance
(* full-duplex)
SC Single-mode, 10/125 µm 10 km
SC Single-mode, 10/125 µm 20 km
SC Single-mode, 10/125 µm 50 km
<Note> The maximum node-to-node network distance is in full-duplex operation.
PCI Express Gigabit Ethernet Adapter
Driver Installation
1. Turn on the computer after plugging PCI Express Gigabit
Ethernet Adapter to PCI Express slot. The “Found New
Hardware Wizard” window pop up.
2. Select “Install from a list or specific location (Advanced)” and
click “Next” to continue.
10 User’s Manual
Indice
Altri manuali Repotec Adattatore
Repotec
Repotec RP-WU5204 Manuale utente
Repotec
Repotec RP-1200ES+ Manuale utente
Repotec
Repotec RP-3200EX Manuale utente
Repotec
Repotec RP-UB215B Manuale utente
Repotec
Repotec UBM302G Manuale utente
Repotec
Repotec RP-PE101 Manuale utente
Repotec
Repotec RP-3200R Manuale utente
Repotec
Repotec RP-1450FC Manuale utente
Repotec
Repotec RP-WU5111A Manuale utente
