Rescue BOOSTER PACK 950 Manuale utente

Owner’s Manual

MODELS 950, 1000, 1800, 2000, 3000

Versatile, Portable DC Power Supply

English, Español, Français Manual/Manuel

quickcable.com/reference

OVERVIEW

RUBBER CAP REMOVED FOR CLARITY

12 VOLT CORD

110 VOLT CORD

12/24 SWITCH (MODEL 2000 ONLY)

Positive (+) Jumper Cable

Negative (_) Jumper Cable

Clamp Lights ON/OFF Switch (Models 1000, 1800 and 3000)

Power ON/OFF Switch

Charge Status Indicator Lights

Battery Level Test Button

Full Charge Light

Reverse Connection Warning LED Light

Charging Light

12 Volt DC Power Outlet & DC Charging Port

120 Volt AC Charging Port (back of unit)

AC & DC Cords

Worklight Switch

Volt Meter

Audible Signal and Light

Clamp Lights (Models 1000, 1800 and 3000)

Rear View of 12/24 Unit (Model 2000 Only 12/24 switch)

GET STARTED

Charge the Rescue Booster Pack before use. It is best to charge the

Booster Pack until the full charge light on the control panel turns on.

Please read all instructions before use.

To ensure maximum battery life, charge at least every 30 days, and

after each use. Extreme ﬂuctuations of either hot or cold outside

temperatures may require re-charging more often.

All models feature an Audible Safety Alarm. When the unit is on,

you will hear an intermittent beep, signaling that there is power to

the booster clamps. If the audible signal becomes a louder, steadier

signal (indicating a polarity problem), disconnect the booster clamps

from the battery immediately. Reverse the clamps and the audible

signal should return to a beep.

COMPONENTS

INSTRUCTIONS

After approximately 10 seconds of continuous cranking of your motor/ignition, stop and wait for 1 minute.

This prevents any damage that could occur to your Booster Pack or vehicle battery due to overheating.

You can turn your Booster Pack back on in approximately 1 minute after this cooling off period.

You can then resume attempts to start your vehicle.

The Rescue Booster Pack has a powerful compact sealed lead acid battery. When it is fully charged,

it has the ability to start multiple vehicles with a 3 to 5 minute wait between each use. Extreme hot

or cold temperatures will vary the performance. The unit will operate, however, the power output will

be lessened.

WARNING: Failure to follow the instructions below may result in personal injury, damage to your vehicle

and the possibility of an explosion. Read the entire Owner’s Manual before use. Always wear safety

glasses during use. Use only in well ventilated areas. Indoor use is not recommended.

1. Turn vehicle ignition off before making cable connections.

2. DO NOT touch RED positive (+) clamp to black negative (-) clamp.

3. Use in well ventilated area, shield eyes.

4. Prior to connection, make sure Booster Pack ON/OFF switch is in the OFF position.

5. Connect RED positive (+) clamp to positive (+) battery terminal or post ﬁrst.

6. Connect BLACK negative (-) clamp to a non-moving metal part of the engine.

7. The Audible Signal and Light will safeguard you if you have hooked the clamps

backward onto the battery terminals or posts. If the alarm sounds and the light

blinks on the handle TURN UNIT OFF IMMEDIATELY. Unhook the Booster Pack

clamps and reverse the connection.

8. Turn the ON/OFF Power Switch to the ON position.

9. Start your vehicle.

10. After starting vehicle, turn Booster Pack ON/OFF switch to OFF position.

11. Disconnect BLACK negative (-) clamp ﬁrst, then disconnect the RED positive (+) clamp.

12. Always wrap Jumper Cables securely into place after use.

13. After use, recharge your Booster Pack.

14. Frequently check charge level of battery by pushing the red

Battery Level Test Button on control panel.

IF BATTERY LEVEL IS ALLOWED TO DROP BELOW LOW LEVEL, PERMANENT DAMAGE TO THE

BATTERY WILL OCCUR AND YOUR RESCUE BOOSTER PACK WILL NOT OPERATE EFFECTIVELY.

Rescue models 1000, 1800 and 3000 are equipped with clamp lights. When required, turn these

lights on via the Clamp Lights ON/OFF switch.

Turn switch OFF when not in use. Do not store the Booster Pack in your vehicle during extreme

periods of hot or cold temperatures; this may diminish the ability of the unit to operate properly.

For optimum performance always store upright at room temperature and recharge every 30 days

and after each use.

DC POWER SOURCE

Operate Cell Phones, Lap Top Computers, Radios, TV’s, Camcorders, Spot Lights, Electric Tools,

Air Compressors, Vacuums, Sump Pumps, etc., simply plug the male plug into the 12 Volt DC

Power Outlet on the front of the unit, identiﬁed with the words “12 V”.

Booster Pack will operate the following items and more:

DC- Powered Product Watts Estimated Time

Lap Top Computer 25 8.5 Hours

Cellular Phone 6 34 Hours

12V Portable TV 60 3.4 Hours

Portable Stereo 50 4 Hours

Spotlight 55 3.7 Hours

12V Car Vacuum 85 2.4 Hours

Time may vary depending on product

manufacturer/model being used and

charge level of the Booster Pack.

RECHARGING

Recharge every 30 days and after each use. Failure to do so will result in possible damage to the internal

battery and result in poor performance or failure to work at all.

1. Plug the AC Charging Cord supplied into the 120 Volt-in connection on the back

of the Booster Pack.

2. Plug the other end of the cord into a 110/120-volt AC outlet.

3. The Yellow charging LED light will glow and will remain ON during the charging

process. When the internal battery is completely full the Green FULL CHARGE

LED light on the control panel will turn on automatically. This can take up to 72

hours depending on the condition of your internal battery. You can unplug your AC

Charging Cord at this time OR leave it plugged in indeﬁnitely as the

CUL™ listed internal charger is ﬂoat charge equipped to maintain the internal battery.

4. You can also charge the unit from your 12 volt power outlet in your vehicle

by plugging one end of the DC charging cord into the Booster Pack 12 Volt DC

power outlet and the other end into your running vehicle’s cigarette lighter.

IMPORTANT: Your BATTERY LEVEL can be at a HIGH CHARGE STATUS when you push your red

Battery Level Test Button . This does not necessarily indicate that the battery is FULLY CHARGED.

To be at the “Full Charge Level” the Green FULL CHARGE light on the control panel will turn on

during the charging process indicating FULL CHARGE status.

PERFORMANCE GUIDELINES

For best results when using your Booster Pack:

• Clean the battery terminals or posts before connecting the clamps to the vehicle

battery. Use a battery post cleaner brush to remove corrosion from the battery

terminals or posts. Two QuickCable cleaners are recommended for cleaning

terminals, posts and cables. Solutions 510420 and 510430 will neutralize the

gray/white powdery corrosive material (see quickcable.com for more information).

WARNINGS: Possible explosion hazard. Contact with battery acid may cause severe burns and

blindness. KEEP OUT OF REACH OF CHILDREN.

• Always wear safety glasses when working with or around lead acid batteries.

• If splashed by battery acid, immediately ﬂush the area of the splash with clean

water; if a burning sensation is felt or any blistering occurs, seek medical help.

If acid is splashed in the eyes, ﬂush eyes with clean water continuously and seek

medical help.

• All lead acid batteries generate hydrogen gas during normal operation. This process

increases during a rapid discharge period such as when using for jump-starting.

Hydrogen gas and battery acid (sulfuric acid) can be:

• Explosive • Poisonous to breath

• Corrosive and will burn skin, eyes and hair • Highly ﬂammable

• Damaging to unprotected metals • Damaging to natural ﬁber clothing

To avoid exposure to battery acid or the possibility of an explosion:

• Follow all instructions in this manual and your vehicle’s manual.

• Only use your Booster Pack in a well-ventilated area.

• Observe all warnings.

MAINTENANCE

• Keep at HIGH or FULL CHARGE status at all times. Refer to

the RECHARGING INSTRUCTIONS of this manual for details.

• Keep the cable clamps clean and free of debris.

• Always protect the unit from direct sunlight,

moisture and heat sources.

• No oil or lubricants are recommended.

• Store upright in a dry area.

• Avoid storing in areas of extreme heat or cold.

www.quickcable.com

WARNINGS

• Model 950, 1000, 1800 and 3000 are

designed to be used only with vehicles

with 12-volt systems. These units are

not designed to be used as a

replacement for a vehicle battery.

• Turn Booster Pack OFF to store;

store upright.

• Do not use the Booster Pack if the cable,

clamp or power cord is damaged.

• Avoid short circuit of the product: Don’t

touch the clamps to any conductive material.

• Don’t store Rescue Booster Pack in places

where the temperature could exceed 120ºF.

• Repairs should be carried out by experts

(only use authorized repair centers).

Attempts to repair unit by untrained

persons may be very dangerous.

• Check your vehicle battery terminals or posts to make sure

they are clean and free of corrosion.

• Check cable clamps are clean and free of debris.

•

Make sure your connections are secure before starting the vehicle.

Twist or rock the clamps slightly until you can feel a tight connection.

• Check the battery status to make sure it is at HIGH or FULL

CHARGE prior to jump starting your vehicle.

If not, charge Booster Pack immediately.

TROUBLESHOOTING

RESCUE BOOSTER PACK LIMITED WARRANTY

Do Not Return the Booster & Power Supply To the Place Of Purchase.

The Manufacturer warrants this product against defects in material or workmanship for one (1)

year from the date of original retail purchase. At our option we will repair or replace.

This warranty does not apply to the battery or compressor. All battery and compressor replacements will

be at the sole discretion of the manufacturer, and subject to visual and internal inspection. Any battery or

compressor replacement will be on a prorated, escalating cost basis to the purchaser, prorated monthly for a

12 month period from the date of purchase (with proof of purchase), and increasing in 1/12th increments

monthly up to the retail battery price set by the manufacturer. Batteries returned with melted terminals,

due to under/over charging or misuse, will not be covered under warranty.

EXCEPT FOR THIS LIMITED WARRANTY, THE MANUFACTURER HAS NOT MADE AND SPECIFICALLY

DISCLAIMS ANY WARRANTY OR REPRESENTATION OF ANY KIND, EXPRESS OR IMPLIED, DIRECT OR

INDIRECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, AND

ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. THIS LIMITED, CONDITIONAL

WARRANTY PROVIDES THE EXCLUSIVE REMEDY FOR ANY CLAIM OR DAMAGE EXCEPT AS

OTHERWISE REQUIRED BY LAW.

This warranty excludes and does not cover defects or failures of your BOOSTER & POWER SUPPLY due to

any cause other than defects in material or workmanship, including without limitation any malfunctions

or failures caused by repairs made by an unauthorized person, mishandling, modiﬁcations, normal wear,

improper storage and unreasonable use or damage.

IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL

DAMAGES. Some states do not allow the exclusion or limitation of incidental or consequential damages

so the above limitations or exclusions may not apply to you. This warranty gives you speciﬁc legal rights

and you may also have other rights which vary from state to state.

Any claim relating to the booster & power supply must be submitted within one (1) year of purchase

and must be sent to Quick Cable in the U.S.A or Canada.

If any portion of this warranty or limitation of rights and remedies is found to be unenforceable, then the

remainder of this document shall remain in full force and effect.

To obtain service under this warranty:

1. Call Technical Service toll free in U.S.A. 1 (800) 558-8667 or in Canada 1 (800) 728-1742. Have

your booster & power supply near the phone and a technician will help you diagnose the problem.

2. When an in-warranty battery is in need of replacement, you must send or fax a copy of your

purchase receipt to Technical Service. They will provide you with the fax number or address. A

replacement battery will be sent to you freight prepaid, and you will be charged for the prorated

amount on your credit card.

3. When an out of warranty battery is in need of replacement, the replacement battery will be

sent to you freight collect or prepaid and added to your invoice.

4. You are responsible for the replacement of the battery and taking the defective battery to the

proper site for recycling.

If your booster & power supply is out of warranty, and fails, it may not be economical to repair.

Before disposing of unit, disassemble, remove battery and recycle.

Quick Cable Corporation

3700 Quick Drive

Franksville, WI U.S.A. 53126-0509

1.800.558.8667

Quick Cable Canada Limited

6395 Kestrel Road

Mississauga, Ontario Canada L5T 1Z5

1.800.728.1742

X890084

For disposal and/or recycling in your area, please

call 800.253.2687 or go to www.cleanup.org.

IT IS ILLEGAL TO DISPOSE OF LEAD

ACID BATTERIES IN THE TRASH!

Quick Cable logo, BilFro, Brute, Cub, Hammer Crimper, HexCrimp, HexCrimp Jr., FlexTube, Fusion, Gardian, HexCrimp,

HexCrimp Jr., MagnaLug, MagnaTube, MAX, Quick, Quick Connector, QuickCote+, QuickCutter, QuickDrive, QuickFlux,

QuickFlex, QuickFuse, QuickHarness, QuickHeat, QuickHold, QuickLink, QuickPower, QuickStrip, QuickTap, Quick

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Rescue Alimentazione elettrica

Rescue

Rescue 950 Manuale utente

Rescue

Rescue 2000 Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente