Resol AM1 Manuale utente

AM1 alarm module

www.resol.com

RESOL AM1 alarm module

Mounting

Connection

Function

Manual

*48005020*

48005020

Thank you for buying this RESOL product.

Please read this manual carefully to get the best performance from this unit.

Please keep this manual carefully.

AM1 alarm module

Table of contents

Safety advice..............................................................2

Overview....................................................................3

Technical Data ...........................................................3

1. Mounting........................................................4

2. Connection....................................................4

3. Function.........................................................5

Imprint .......................................................................8

Subject to technical change. Errors excepted.

Description of symbols

Signal words describe the danger that may occur, when it

is not avoided.

Warning means that injury, possibly life-threatening injury,

can occur.

Attention means that damage to the appliance can occur.

Information about the product

Proper usage

The RESOL AM1 alarm module is to be used as an interface

for the failure signal transmission between RESOL devices

and external applications in compliance with the technical

data speciﬁed in this manual.

Improper use excludes all liability claims.

Note

Notes are indicated with an information symbol.

Arrows indicate instruction steps that should be→

carried out.

Safety advice

Please pay attention to the following safety advice in order

to avoid danger and damage to people and property.

Instructions

Attention must be paid to the valid local standards, regu-

lations and directives!

This manual contains important information about safe and

proper usage of this product. Please keep this manual for

future reference.

Target group

These instructions are exclusively addressed to authorised

skilled personnel.

Only qualiﬁed electricians should carry out electrical•

works.

Initial installation must be effected by qualiﬁed personnel•

named by the manufacturer

WARNING! Warnings are indicated with a

warning triangle!

They contain information on how→

to avoid the danger described.

Note

Strong electromagnetic ﬁelds can impair the

function of the device.

Make sure the device is not exposed to→

strong electromagnetic ﬁelds.

Disposal

Dispose of the packaging in an environmentally sound•

manner.

Dispose of old appliances in an environmentally sound•

manner. Upon request we will take back your old

appliances bought from us and guarantee an environ-

mentally sound disposal of the devices.

AM1 alarm module

3 |

AM1 alarm module

The AM1 alarm module is designed to signal system failures. It is to be connected

to the VBus®of the controller and issues an optical signal via a red LED if a fai-

lure has occurred.The AM1 also has a potential-free relay output, which can e. g.

be connected to a building management system (BMS).Thus, a collective error

message can be issued in the case of a system failure.

Depending on the controller and the sensors connected,different fault conditions

can be signalled, e. g. sensor failures, excess or negative system pressure as well

as errors in the ﬂow rate, such as a dry run of the pump.The AM1 alarm module

ensures that occurring failures can be immediately recognized and repaired,even if

the system and the controller are difﬁcult to access or located in a remote place.

Thus, the reliability and the stable yield of the system are ensured.

Technical data

Housing: Plastic

Upper part of the housing:

PC 2207 UV

Base part of the housing:

Karilen E 42 D - H201

Protection type: IP 54

Ambient temperature: -13 ... +158 °F

Dimensions: 111 × 68 × 40 mm

Mounting: Wall mounting

Display: 1 LED

Power supply: via RESOL VBus®

Interface: RESOL VBus®

Output: 1 potential-free relay

Switching capacity: 30 VDC, 1 A;

125 VAC, 0,5 A

Included

AM1 alarm module•

accessory bag with•

2 × screws and wall plugs for wall

mounting

1 × terminal block

Overview

Reliable failure signal by LED•

Connection to a Building Management System (BMS) possible•

Supply and control via RESOL VBus•®

Sturdy and weatherproof housing in shapely design•

Simple installation•

64,07 mm

67,79 mm

111 mm

40 mm

34 mm

The AM1 can be connected to all

RESOL devices equipped with aVBus®.

AM1 alarm module

ATTENTION! Low voltage cables must not run to-

gether in a cable conduit with cables

carrying a higher voltage than 50V.

Pay attention to the local regula-→

tions!

ATTENTION! ESD damage!

Electrostatic discharge can lead to da-

mage to electronic components!

Take care to discharge properly→

before touching the inside of the

device!

The AM1 is designed for simple connection to RESOL

controllers or calorimeters via the RESOL VBus®. A power

supply connection is not necessary.

For easier access to the terminals, the circuit board can be

taken from its retaining ﬁxture.

Connect the VBus®cable to the terminals marked „VBUS”

with either polarity.

To the terminals marked „REL”, a load can be connected

with either polarity. When connecting a load, observe the

switching capacity stated in the Technical data on pg. 3.

The bus cable can be extended with a two-wire cable

(bell wire).The cross section of the cable must be at least

0,5 mm2and the cable can be extended up to 50 m in the

case of a single connection.

2. Connection

Terminals of the AM1

Lower part of the housing

1. Mounting

To mount the AM1, proceed as follows::

Unscrew the housing screw and pull off the upper part→

of the housing upwards

Mark the fastening points on the wall (centres 5 cm)→

and drill the necessary holes

Screw the lower part of the housing to the wall using→

the screws and wall plugs from the accessory bag

Relocate the upper part of the housing and refasten it→

Upper part of the housing

Note

If a moisture protection is necessary, mount the

device vertically.

AM1 alarm module

5 |

The AM1 alarm module is an interface for the failure signal

transmission between RESOL devices and external appli-

cations. It is to be connected to a RESOL controller or

calorimeter via the RESOL VBus®.

When theAM1 is operational,the LED will glow continuously

to signal operational readiness.

If the LED does not glow, check the connection of the→

device!

The AM1 receives and processes the VBus®data packets

of the device connected. In the case of an incoming failure

signal, the integrated LED ﬂashes and the AM1 operates a

potential-free relay.

The relay can e. g. be used to connect an additional signal-

ling device, or to connect to a building management system

(BMS).The failure signals can thus be issued as a collective

error message by the BMS.

3. Function

AM1 alarm module

Notes

AM1 alarm module

7 |

Notes

AM1 alarm module

Distributed by:

Please note:

The design and the speciﬁcations may be changed without notice.

The illustrations may differ from the original product.

RESOL - Elektronische Regelungen GmbH

Heiskampstraße 10

45527 Hattingen / Germany

Tel.: +49 (0) 23 24 / 96 48 - 0

Fax: +49 (0) 23 24 / 96 48 - 755

www.resol.com

info@resol.de

Reprinting / copying

This mounting- and operation manual including all parts is

copyrighted. Another use outside the copyright requires

the approval of RESOL - Elektronische Regelungen GmbH.

This especially applies for copies, translations, microﬁlms

and the storage into electronic systems.

Editor: RESOL - Elektronische Regelungen GmbH

Important notice:

The text and drawings in this manual are correct to the

best of our knowledge.. As faults can never be excluded,

please note: Your own calculations and plans, under consi-

deration of the current standards and national regulations

should only be basis for your projects.We do not offer a

guarantee for the completeness of the drawings and texts

of this manual - they only represent some examples.They

can only be used at your own risk. No liability is assumed

for incorrect, incomplete or false information and / or the

resulting damages.

Altri manuali per AM1

Indice

Altri manuali Resol Sistema di sicurezza

Resol

Resol AM1 Manuale utente

Resol

Resol AM1 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente