Resource SDGF-001 Guida utente
Fingerprint Iden�fica�on glass lock
SDGF-001
Quick Opera�on Guide
Important informa�on:
Please read this claims, before using this product
Appearance and fuon introduc:
Charge the baery
1. Open the USB cover
2. Plug in the Micro USB cable and connected to the external power
supply, charging red LED lights up
3. Remove the external power supply, while reach the full charge
(charging red LED turns)
Limited warranty:
This warranty stated herein shall NOT apply, if: (1) this Product has not
been used in accordance with any accompanying instrucons, (2) this
Product has not been used for its intended funcons and environment, (3)
the arial malicious damage or personal negligence cause any defects,
(4) if this Product has been opened, modied or repaired by anyone other
than an authorised service centre, or if it is repaired using unauthorised
spare part; Or because of an accident or other external factors causing any
malfuncon or defects. To use this Product in the above manner or the
similar way, which will be at your own risk.
Unlock
1. Press the buon once, the status green LED is shing
2. Press the sensor wier (At this moment, If your
erprint has been iden quickly unlock, accompanied by a
beep sound)
Lock
1. SDGF-001 has been unlocked
2. Press the buon once (at this moment, SDGF-001 immediately
locks up, accompanied by 2 beep sounds)
Register fingerprint
1. Unlock the SDGF-001 to get the authorized of registraon.
2. When the green ledll lit, press and hold the buon
connuously unl the red and green LED interacveh and
heard a beep sound.
3. Now, release the buon and start to press er onto the
erprint sensor for scanningerprint, remove yger
when you hear a beep sound and the green LED lights on once.
4. Repeat step 3 ( for the same nger) unl you hear a long beep
sound, completely register erprint (pay aenon: To
generate an ecvegerprint registration, must complete 7
mes scans)
5. The green and red LED will interacveh again to allow you to
repeat step3~4 to register another or Press the buon once
to stop the registraon.
Clear fingerprint
1. Unlock the SDGF-001 to get the authorized of registraon.
2. When the green ledll lit, press and hold the buon
connuously unl the red and green LED interacve flash and
heard a beep sound then release the buon.
3. Press and hold the buon again unl you hear a long beep sound
(at this moment, allgerprints have been cleared)
Appendix A:
Trouble shoo�ng
Iden�fy fingerprint successfully but it cannot be unlocked
Please make sure there is no external tension on the buon,
applying tension to the buon will aect the motor’s unlocking
funcon.
In case, you encountered above situaon, please follow out
below procedures to unlock
1. press the buon once again to lock SDGF-001.
2. Try to do the unlock again but note that to avoid to apply
tension to the buon.
Press the finger onto the fingerprint sensor, nothing happened
Please make sure that you have pressed the buon once to get
power, SDGF-001 will automacally enter the power-omode if
there is no any operaons aer 5 seconds to enhance the baery
life.
In case, you encountered above situaon, please follow out below
procedures to unlock
1. Press the buon once
2. Press yngerprint to unlock.
Try to plug USB cord in to USB connector to supply the emergency
power and do charging for the SDGF-001.
The fingers can’t be iden�fied
Make sure yger is not wet or sweated.
Make sure that enough pressure has been applied to the sensor, It
will be misjudgment if there’s no enough pressure to apply to the
sensor.
Make sure the ngerprint(s) what you are using for idencaon
has been registered successfully.
Make sure the sensing area of nger is same as your registraon.
Fingerprint can’t be registered
Make sure there are not up 30 ngerprints have been registered,
SDGF-001 can be maximum store 30 sets of gerprints, you may
need to clear the ngerprints to get the space for negerprint
aer 30 gerprints have been registered.
There’s no any response during opera�on
Check the baery power, you can use the USB cord to do the
emergency procedure or baery charging to back to normal
operaon.
Use a sharp object to press the reset buon to restore the normal
operaon, Occasionally the electronic product may be crashed
when it is disturbed by an unidenexternal force (such as
electromagnec waves, stac electricity and so on), In this case,
the reset buon must be used to restore the normal operaon.
Indice
