ReSPR FLEX Manuale utente
www.resprtech.COM
ReSPR
FLEX
Owner’s Manual
ReSPR
Technologies
2
Welcome
Welcome to ReSPR FLEX.
ReSPR FLEX is designed to provide years of trouble-free service
when it is properly maintained. Even when properly cared for, some
parts of your ReSPR FLEX will need to be replaced periodically.
Replacement parts can be purchased from your authorized
distributor or directly from ReSPR Technologies.
(www.resprtech.com)
ReSPR
Technologies
3
Quickstart 4
Warnings 5
Setup & Operation 6
Diagrams 8
Routine Maintenance 12
Troubleshooting 15
Limited Warranty 17
Records/Specifications 18
Contents
ReSPR
Technologies
4
Quickstart
1 Place ReSPR FLEX on a counter top or shelf, not on the
floor. Ensure there is room in front and back of the unit for
air to flow through.
2 Plug the unit in with the included power cable.
3 Insert one lithium battery (CR20253V) inside the remote
control.
4 Power on with the remote or by pressing the display screen
then set the fan to a comfortable sound level. Leave the
ReSPR FLEX in NORMAL Mode - Screen will read PCO
(PhotoCatalytic Oxidation) or NCC (Natutal Catalytic
Conversion). This is the standard mode for occupied rooms.
HIGH mode is used for stronger purification needs.
2
1
4
3
5
Use the AWAY MODE for a higher level of
disinfection when space is not occupied.
Pressing the Away Mode key will start
a timer (2 to 8 hours). The ReSPR FLEX
will go back to Normal Mode when the
timer ends or when you push NORMAL
Mode again.
NEVER USE AWAY MODE
WHEN ROOM IS OCCUPIED
Fan
speed
Purification
level
Size of the room
(only set in HIGH mode)
5
Warnings
Review this list before using or performing any maintenance or cleaning of your unit.
WARNING: Never operate unit near a heat source, open flame or flammable/combustible fluids.
WARNING: Do not operate unit unless all parts (including Cell, Purification Plate, Rear Filter Assembly and Rear Cover) are
properly installed.
CAUTION: Directly viewing the lamp inside unit for an extended period (longer than 20 min.) may result in eye damage.
CAUTION: Never adjust setting to exceed square footage of ventilated space being treated.
CAUTION: Do not use AWAY MODE in occupied spaces. Short term exposure to ozone levels exceeding 0.5 ppm can cause
temporary adverse reactions.
CAUTION: Unit should be powered OFF and Power Cord should be disconnected when Cleaning/Disassembling/
Reassembling/Servicing.
WARNING
CAUTION
CAUTION
WARNING
CAUTION
CAUTION
6
Ideal Placement
• Make sure the location you choose is as close to an air
supply duct as possible and as far away from the HVAC air
return duct as possible. This will ensure that the oxidizing
molecules produced by the ReSPR FLEX are optimally
circulated.
• Each ReSPR FLEX can eectively treat 3,000 sq feet of
space as long as there is air circulation in the space. Be sure
doors are open in areas that you wish to treat.
• To ensure the unit works properly, there should be as much
space as possible in front of your ReSPR FLEX so that It
can eciently process the air in the area.
• Place ReSPR FLEX on a shelf or counter top.
Never place an operating unit on the floor.
Operating ReSPR FLEX
1. Connect the Power Cord to the Power Adapter and the
Power Adapter Plug into the unit. (Check to be sure your
power supply is properly assembled. The Power Cord should
be inserted far enough into the Power Adapter so that a
space of only about 1/8 in. is left between the widest part of
the power cord and the edge of the Power Adapter).
2. Insert the Power Plug into the wall outlet.
3. Turn on the unit by pressing the POWER button and set
it to NORMAL mode. The screen will read NCC (Natural
Catalytic Conversion). This is the optimal setting for
running ReSPR FLEX continuously in your oce or home.
Adjust the fan to a comfortable sound level using the up
and down buttons next to the display.
4. ReSPR FLEX comes with a remote control and one lithium
battery (CR20253V) for easier operation when the unit is
placed on a high shelf.
Set up and Operation
(Initial Setup)
6
7
When to use NORMAL Mode
• Normal mode should be the default mode for continually
running your ReSPR FLEX in occupied space.
When to use HIGH Mode
• High mode is used for stronger purification needs,
removing pollutants like smoke or other significant odors.
• When ReSPR FLEX is set to HIGH Mode the display will ask
you to set the room size (ft2or m2). Press the PURIFIER
button up or down to set the size of the room for the most
eective treatment. NEVER set the High Mode higher than
the square footage of the room.
When to use SLEEP Mode
• Access sleep mode on your remote control. Activating this
setting will dim the display screen settings.
When to use AWAY Mode
• AWAY Mode generates ozone for deep cleaning an area.
This mode can be used for removing smoke, cooking odors,
mold spores, viruses and bacteria. AWAY mode runs on a
timer and once it completes the cycle, it returns to Normal
Mode.
• Set AWAY Mode by pressing the AWAY Mode button. Each
time you press the button it will increase the time of the
cycle from 2:00, 4:00, 6:00 or 8:00 hours.
• If Away Mode is running when you enter the room, push the
Normal/High button once to return to Normal Mode.
NEVER USE AWAY MODE IN OCCUPIED SPACES
Child Lock function
• ChoosepresstheAwayModebuttonfor5secondstoactivatethe
lock function, press that button again to unlock the keypad.
Operating Modes
Normal: Continual Usage: 24/7; High: Continual Usage: 24/7;
Away: Limit to unoccupied spaces ONLY
8
Ionization Needle
1
Front Grille2
Control Panel
3
Rear Cover Screw
1
Rear Cover Grooves2
Power Adapter Inlet
3
Rear Cover
1
Unit Rear2
Unit Front
3
1
2 3
Front of Unit Rear of unit Side of Unit
Diagrams (Unit)
1
2
3 1
2
3
9
Filter Assembly1
NCC Cell
1
NCC Cell Nuts2
NCC Connector
3
Power Cord
1
Power Cord Plug2
Power Adapter
3
Power Adapter Plug
4
Purification Plate
4
Rear of Unit
(Rear Cover Removed)
Rear of Unit
(Filter Assembly Removed)
Power Supply
1
2
3 4
1
3
4
1
2
(Unit)
10
1
2
3
6
5
4
Power Button
1
Purification Level Control
2
m2 / ft2 Control
3
Sleep Mode Control
4
Fan Level Control
5
Away Mode Control
6
Diagrams (Controls)
Remote Control Panel
10
1
2 4
5
3
Power Button
1
Fan Speed Control
2
3
4
5
Power Button
1
Fan Speed Control
2
3
4
Purifier Level Control
5
Away Mode Toggle
Normal/High Toggle
Indice
