Revo 0211T4FD Manuale utente
V1.01
Wi-Fi Kit Quick Guide
1
1Default IP, Username and Password
IP address:
NVR
192.168.1.30
NOTE!
For security, you are strongly recommended
to set a strong password of at least nine
characters including all three elements:
digits, letters and special characters.
IPC
192.168.1.13
Username:
admin
Password:
123456
2Disk Installation
The illustrations are for reference only. The actual device may vary.
1. Loosen the screws and remove the
cover.
2. Secure the disk by fixing the screws
to the screw holes shown in the
figure.
3. Connect data cables and power cables
to the disk.
4. Put the cover back in place and
tighten the screws.
2
3(Optional) Install SD Card
Some camera models support Micro SD card. You need to open the bottom cover to
install the SD card. Do not hot plug the Micro SD card after it is inserted. Otherwise
the camera or the SD card might be damaged.
1. Open the bottom cover.
2. Insert the SD card properly.
4Connect the Kit
The following part shows an example. The actual device may vary.
1. Connect the NVR to a monitor with a VGA or HDMI cable (not included in the kit).
2. Plug a mouse into the USB interface on the NVR.
3. Connect the NVR and the camera to power.
NVR Interfaces
Micro SD slot
Audio
output
USB
Network
interface
GND Power
supply
Antenna
interface
VGA
Antenna
interface HDMI
IP Network
Monitor Monitor
E.g.,loudspeaker
Mouse
3
IPC Interfaces
5Device Operation
5.1 Startup and Shutdown
Make sure the cables are connected correctly and the device is grounded properly.
Use a power supply that meets requirements.
5.1.1 Startup
Connect the devices to power to start up the devices.
5.1.2 Shutdown
Click > Shutdown on the screen toolbar in live view page.
CAUTION!
Do not disconnect power when the NVR is operating or shutting down.
5.2 Wi-Fi Configuration
The camera will get online and start live view on the NVR once the NVR and camera
are connected to power. Follow the steps to change Wi-Fi settings.
1. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP.
2. Change settings as needed:
IP
Network
Network
interface
Power
interface
Antenna
SD card
4
SSID: MAC address by default, you can change as needed.
Password: The default is the last eight digits of the serial number. You are
strongly recommended to change into a strong password.
Region, Channel: Signal interference varies with region and channel. You are
recommended to choose a channel with less signal interference.
Wireless NIC IP: The IP address of wireless NIC. The NVR assigns IP address to
connected devices based on the start and end IP address range.
CAUTION!
The NVR's wireless NIC IP must be in a different network segment with its LAN IP
address.
3. Click Apply.
NOTE!
After SSID or password are changed on the NVR, the new SSID or password will be
synchronized to online cameras. For offline cameras, the changed settings cannot
be synchronized, and you need to pair the camera with the NVR again. See 5.3 Pair
Devices Again for details.
5.3 Pair Devices Again
If you change Wi-Fi settings on the NVR when cameras are offline, you need to pair
5
devices again. Choose one of the following methods as needed.
NOTE!
The following methods are also applicable if you pair a camera not in the kit with
the NVR.
One-Click Pair
1. Connect the camera and the NVR to the same switch (or connect the camera to
the NVR with a network cable), and connect the devices to power.
2. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP.
3. Press the RESET button on the back of the camera to restore factory default
settings.
NOTE!
The reset button only works in 1-10 minutes after the camera is powered on. If you
fails to press the button within the time range, you need to power off the camera
and then on again to restore the defaults.
4. Click One-Click Pair.
NOTE!
This function works within 3 minutes after the camera restores defaults. So, if the
camera is not paired successfully within this time, please restart the camera or try
other methods.
5. Wait for the camera to get online.
QR Code Pair
1. Connect the camera to power.
6
2. Press the RESET button on the back of the camera to restore factory default
settings.
3. Right-click on the NVR and then choose Menu > Network > Wi-Fi AP.
4. Click QR Code Pair, and follow the on-screen instructions to scan the QR code.
5. Wait for the camera to get online.
Use EZView
Please refer to 8.5 Pair Camera and NVR for detailed steps.
6Install Devices
6.1 Wi-Fi Signal Connectivity
The antenna sends Wi-Fi signals in all directions around it. Wi-Fi
connectivity is the best when antennas are parallel with each other, and
is the weakest when the top of an antenna points directly to the top of
another. Please arrange the antennas properly to improve Wi-Fi
connectivity.
Installation with Strongest Signal
7
Installation with Weakest Signal
6.2 Install the Camera
The following part takes wall mount as an example. Make sure the wall is strong
enough to support the weight of the camera. Please prepare hardware accessories
in advance.
1. Paste positioning stickers on the
wall and drill 30mm-depth guide
holes using a φ6-6.5mm drill bit.
2. Knock the plastic rivets into the
guide holes and ensure that they
are tightened up.
3. Screw the locknut to loosen the
universal joint, and attach your
camera to the wall.
4. Rotate the antenna to the
antenna interface in clockwise
direction.
5. Adjust the monitoring direction.
6. Connect the camera to power to
start up.
antenna
interface
8
7Playback
In the preview page, select the desired window, then right click and select Playback
to play the recording of the current day.
NOTE!
A 7*24 recording schedule is enabled by default. To set a recording schedule
manually, right click and select Menu > Storage > Recording and then set
recording type and time based on your needs.
If you choose Event type recording, you need to enable the corresponding
alarm function and configure alarm-triggered recording/snapshot first.
8EZView
Please download EZView on the App Store (iOS) or on Google Play (Android) first.
8.1 Sign Up an Account
1. Tap in the upper right corner and choose International service area.
2. Tap Sign Up and follow the steps to complete sign up.
9
8.2 Add Devices
After logging in to your account, tap > Devices > Add, then select a way to add
devices. It’s recommended to choose Scan and scan the QR code on the device body.
8.3 Live View/Playback
Tap > Live View/Playback. Tap in a window, then select a device to start live
view or playback. You can also tap in the upper-right corner and select device(s).
8.4 Share Devices
Tap > Devices, select the desired device and tap Share, then complete the
sharing settings. You may also share the device by generating a QR code.
Indice
