Revolabs 01-EWM-DR-BLK Istruzioni operative
REVOLABS Elite™
Wired Microphones
Installation and Operation Guide
Models:
01-EWM-DR-BLK 01-EWM-OM-BLK
01-EWM-DR-WHT 01-EWM-OM-WHT
01-EWM-DR-BNI 01-EWM-OM-BNI
2
© 2014 REVOLABS, INC. All rights reserved. No part of this document may be
reproduced in any form or by any means without express written permission from
Revolabs, Inc. Product specifications are subject to change without notice.
Revolabs Eilte Wired Microphone Installation and Operation Guide
10-EXECWMGUIDE-EN
NOVEMBER 2014 (Rev 1.0.1)
3
Introduction
Congratulations on your purchase of the Revolabs Elite™ Wired Microphone.
This microphone utilizes state of the art technology providing high bandwidth
audio and enabling clear, reliable audio capture for your applications.
Please read this documentation carefully and follow the instructions before
installing and using your Elite™ Wired Microphone.
4
Safety and General Information
Please read the following information to ensure safe and efficient use of your Revolabs
system.
FCC Notice to Users
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Users are not permitted to make changes or modify the equipment in any way.
Changes or modifications not expressly approved by Revolabs, Inc. could void
your authority to operate this equipment under Federal Communications
Commission’s rules.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and the receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: "How to
Identify and Resolve Radio-TV Interference Problems." This booklet is available
from the U.S. Government Printing Office, Washington D.C. 20402
5
Industry Canada Notice to Users
Operation is subject to the following two conditions:
(1) This device may not cause interference and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Notice to European Customers
Revolabs, Inc.
190, High Street,
Tonbridge, Kent,
TN9 1BE,
UK.
Declare that for the hereinafter mentioned product model numbers, the
presumption of conformity with the applicable essential requirements has been
approved in accordance with the Electromagnetic Compatibility (EMC) Directive
2004/108/EC, and RoHS II Directive 2011/65/EU.
Model Number:
Description:
01-EWM-DR
Elite Wired Directional Mic
01-EWM-OM
Elite Wired Omnidirectional Mic
Any unauthorized modification of the products voids this Declaration.
For a copy of the original signed declaration of conformity, please contact
Revolabs at the above address.
6
WEEE Notification
The Waste Electrical and Electronic Equipment (WEEE) directive (2012/19/EU)
is intended to promote recycling of electrical and electronic equipment and
their components at end of life.
According to the requirement of the WEEE legislation the following user
information is provided to customers for all branded Revolabs products subject
to the WEEE directive.
“The symbol on the product or its packaging indicates that this product must
not be disposed of with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at
the time of disposal will help conserve natural resources and ensure that it is
recycled in a manner that protects human health and the environment. For
more information about where you can drop off your waste for recycling, please
contact your local authority, or where you purchased your product.”
Safety Warnings
•Follow the instructions in the Revolabs Elite Wired Microphone Installation
and Operation Guide.
•Do not expose any of the Elite Wired Microphones to water, moisture, or
high humidity.
•Do not expose any of the Elite Wired Microphones to extreme high or low
temperatures.
•Do not expose any of the Elite Wired Microphones to lit candles, cigarettes,
cigars, or to open flames, etc.
•Do not drop, throw, or try to bend the microphones, as rough treatment
could damage them.
•Do not open the casings of any of the Elite Wired Microphones.
•Do not use any other accessories than Revolabs’ originals intended for use
with this product. Use of non-original accessories may result in loss of
performance, damage to the product, fire, electric shock or injury. The
warranty does not cover product failures which have been caused by use
of non-original accessories.
7
Content
Introduction.................................................................................................................2
Safety and General Information ...................................................................................4
FCC Notice to Users .................................................................................................4
Industry Canada Notice to Users ..............................................................................5
Notice to European Customers .................................................................................5
WEEE Notification....................................................................................................6
Safety Warnings...........................................................................................................6
Content .......................................................................................................................7
Components ................................................................................................................8
Installation ..................................................................................................................9
Microphones ..............................................................................................................10
The Elite Omni-Directional Wired Tabletop Boundary Microphones........................10
The Elite Directional Wired Tabletop Boundary Microphones .................................11
Warranty ...................................................................................................................12
Technical Support......................................................................................................13
Specifications ............................................................................................................13
8
Components
Your Revolabs Elite Wired Microphone comes with a 15’ (4.5 m) cable attached
to connect it to a phantom powered microphone input of a digital signal
processor (DSP), or other audio devices. The packaging includes the
microphone with cable and a short installation documentation.
The Revolabs Elite system is designed to optimize audio capture by providing
consistent and high-level audio input from all participants.
You might have purchased additional components like the installation kit to
install your microphones permanently. Please review the documentation of
these components for their installation information.
9
Installation
The Revolabs Elite Wired Microphone has a 15 feet cable attached that hosts
three wires. The three wires are red, black, and the shield/ground.
Connect the red wire to the positive (+) microphone input of the DSP or audio
equipment you use with the microphone. Similarly, connect the black wire
with the negative (-) input of the DSP. When connecting to a male XLR
connector, use the following polarity:
1 – Ground / Shield
2 – Positive (+)
3 – Negative (-)
Note: The Elite Wired Microphone includes some active electronic
circuitry, and therefore requires Phantom Power to be provided
from the device the microphone is connected to. The Elite Wired
Microphone requires a phantom voltage between 9 and 48V DC,
with a draw of maximum 2mA.
Red – positive (+)
Black – Negative (-)
Shield - Ground
10
Microphones
Revolabs Elite Wired Microphones come in two different versions:
•Revolabs Elite Omni-directional Tabletop Wired Boundary Microphone
•Revolabs Elite Uni-directional Tabletop Wired Boundary Microphone
The Elite Omni-Directional Wired Tabletop Boundary
Microphones
The Elite Omni-directional Wired Tabletop Boundary Microphones enable
multiple conference attendees to use a single microphone.
1. Bottom door latch — replace the bottom cover for permanent installations
using this latch.
2. Audio wire — connect the microphone to the DSP or other audio equipment
using this wire.
2
1
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Revolabs Microfono
