Revvi ABT-E250 Manuale utente
Owner's Manual
MODEL: REVVI ABT-E250
Read and understand this entire manual before riding!
Note: Appropriate protective equipment to be
worn at all times, children must be supervised
by an adult at all times. It is always at the
p a r e n t ’ s discretion as to the age of the rider.
Note: Manual illustrations are for demonstration purposes
only. Illustrations may not reflect exact appearance of actual
product. Specification subject to change without notice.
Warning:
The use of this product can be dangerous and could
potentially cause serious injury. Children must be supervised
at all times when using this device. Anyone riding this device
must wear a helmet, knee pads, elbow pads and gloves. Keep
away from steep hills, other vehicles, roads, bodies of water,
animals, pedestrians and be vigilant of any other potential
hazards before use. Please read all assembly and safety
instructions before use. By purchasing this product you
accept responsibility of the devices proper use, maintenance,
supervision of rider and all risks associated with its use. The
retailer and manufacturer are not responsible for any
damage, injury or death resulting from the use of this
product. It is always at the parent or person supervising as to
the age of the rider.
Essential Technical Parameters
1. Vehicle
-Bike weight: 23kg
-Maximum load (weight):75kg;
2. Motor
-Type: DC, with brush;
-Rated continuous output power: P=250W;
-Rated speed: 275±7.5%rpm;
-Rated voltage: 24V;
-Rated output torque: 1.21 (N.m)
3. Controls
-Rated input voltage: 24V;
-Input voltage range: 20~28V;
-Input current without load:≤115MA；
-Max. output current of the motor: 30±1A;
-Under-voltage protection (Vqn) :20±0.5V;
-Max. conduction value: ≤95% (with the output current of
the control<2A);
-Starting voltage of handlebars: ≥1.4V；
-Protection voltage of the handlebars: ≤1.8V;
4. Charger
-Input: 100-240 VAC, frequency 50/60 Hz, input current:
1.8A Max;
-Output : 24V DC 1.5A
5. Batteries
-Size 152*65*94 mm;
-Type: Lead Acid Battery, 2×12V, 10AH.
Names of all structural components
Assembly
Your Revvi arrives almost completely assembled, making it easy to
start riding. The only assembly required is to attach the handlebars.
All cables and controls already hooked up to the bike, so attaching
the handlebars is easy:
1. Using the 6mm Allen key attach the lower parts of the
handlebar clamps to the top of the forks. Do not tighten
until the handlebars are in place!
2. Place the handlebars into position in the lower clamps.
Take care to get the handlebars centered side so side, and
set in your desired upright position.
CAUTION Be careful not to lean the handlebars too far
forward or backward as this will affect the bike’s handling
and comfort of the ride.
3. Place the top parts of the clamps in position over the
handlebars and tighten the four bolts securely to 18-
26N.M. DO NOT OVERTIGHTEN.
4. Now tighten the two bolts holding the handlebar risers
to the forks to 18-26N.M. DO NOT OVERTIGHTEN.
Charge the battery
First, be sure that the toggle switch on the top of the “tank” is
switched to the off position.
Locate the battery charger port which is on the right side of the
bike and flip up the small round black protective cap. Under this
cap you will see a round connector with three small contact posts.
Note that there is a small locating spline at the bottom of the
connector.
On the round end of the battery charger cord, you will see a plug
that has three small holes a notch which fits into the connector on
the bike.
1. Plug the charger into a wall outlet. If the lights on the charger
do not light up. Check the power to the outlet. If necessary, try
a different outlet.
2. Turn the bikes power switch OFF before charging. Plug the
charger into the charger port on your Revvi.
3. The light on the charger should be red. You need to leave it on
charge until the light goes green. The green light indicates that
it is fully charged.
It is important to charge the battery fully before using it for the
first time.
OPERATING CONTROLS
To operate your Revvi you need to be able to operate the throttle,
brake and other controls without stopping to look at them. Please
study the image below carefully to become familiar with the
function and the location each control.
When operating your Revvi there are some key operating controls
and components that allow you to operate your bike.
Their location and operation information is shown below.
1.On/Off Switch 2.Throttle 3.Brake
ON/OFF SWITCH
The ON/OFF switch is conveniently located just
ahead of the driver and is equipped with a flip-
up cover. The cover, when closed also shuts off
the On/Off switch. The switch should be left in
the off position whenever the bike is not being
used to protect the charge that is in the
battery. You will know that the switch is on
when the charge indicator lights on the throttle
are lit.
THROTTLE
The throttle allows the rider to send power to
the motor and make the bike move forward.
The power and speed is variable due to the
twist-grip throttle mechanism.
DANGER When giving the throttle power,
twist it slowly at first to avoid sudden
acceleration
BRAKE
Your Revvi is equipped with a rear disc brake.
The brake lever is hand operated and is on the
left hand grip mounted to the handlebars.
Squeeze the brake carefully with increasing
force to stop the bike.
DANGER Applying the brakes too quickly can
cause the bike to skid and you may lose
control.
2-Stage Safety Speed Limiter
The Revvi is equipped with a special switch that reduces the speed
to accommodate younger, smaller riders. The switch is located
inside the battery case, under the battery in a hard to reach spot to
limit access by inquisitive smaller children.
NOTE: The 2-stage safety speed limiter switch is set at the factory
to the slower speed setting. To switch from slow speed to regular
speed, or vice-versa, follow the steps below.
1. Lift the front of the bikes up or lean the bike on its side.
2. These is a small hole in the bottom of the plastic covers that
protect the batteries. Reach through the hole with your finger
and flick the switch from “I" (slow speed) to “O” (fast speed).
3. Your Revvi is now set to its fastest setting. To return the bike to
the slow speed setting follow these steps but flick the switch
back to "I".
Balance wheels
Your Revvi bike includes a set of balance wheels as shown on the
structural components page. We recommend that you use these
balance wheels for any novice rider who has no previous riding
experience without them.
The balance wheels are easy and simple to fit:
1. Remove the extra nut supplied on each side of the rear axle.
CAUTION! Do not remove the nuts holding the rear axle in place!
2.Fit a balance wheel to each side of the rear axle.
3. Fix the balance wheels in place with the two nuts you removed
from the axle.
CAUTION! Please ensure the balance wheels are done up tight so
they cannot move whilst the bike is been ridden.
Indice
