REXROTH CS 550/150RC Manuale utente
CS 550/150RC
Spreader Joystick Controller Operator Manual
2/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
Table of Contents
1
Panel Controls
3
2
Program Screen Layout
4
3
Screen Controls
5
3.1
Pause
5
3.2
Blast
5
3.3
Reverse
5
3.4
Change Solid Material
6
3.5
Change Prewet Material
6
3.6
Manual Gate Adjustment
6
3.7
Error Messages
7
4
Symbol Actions
7
4.1
Error Log/Diagnostic –Gear Symbol
7
4.2
Unloading –UNLOAD Symbol
8
4.3
Data Retrieval/Clear Trip Summary –USB Symbol
9
4.4
Brightness/Volume Adjustment –Backlight Symbol
9
4.5
Manual Hydraulic Gate Adjustment –Cylinder Symbol
10
4.6
Programming Mode –Lock Symbol
10
5
Joystick Control
11
5.1
Button Status
11
5.2
Joystick Status
11
5.3
Joystick Screen
11
6
Anti-ice Mode
12
7
Pattern Mode
13
8
Air Gate Mode
13
9
Liquid+ Mode
14
10
Cross Conveyor Mode
14
11
Spinner Reverse Mode
15
12
Error Codes
16
13
Warning
18
Bosch Rexroth Canada Corp. reserves the right to revise this information at any time and for
any reason and reserves the right to make changes at any time, without notice or obligation,
to any of the information contained in this piece of literature.
Please check for updates at: www.boschrexroth.ca/compu-spread
3/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
1 Panel Controls
Turn knobs clockwise to increase.
4/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
2Program Screen Layout
SPNR
SALT - -
LIQUID1
Spinner Label
Spread Width %
Spinner Setpoint
Spinner Mode
Pause Button
Solid Name
Gate Mode/Solid Rate
Gate Position/Conv Set.
Conveyor Mode
Blast Button
Liquid Name
Liquid Rate
Liquid Setpoint
Liquid Mode
Reverse Button
Trip Summary
Toggle between Total and Spreading Distance (S)
Total Quantity
Total Prewet Volume
Total Anti-icing Volume
5/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
3Screen Controls
3.1 Pause
Press the Pause button to pause, and press again to resume spreading.
3.2Blast
Press the Blast button to increase the spreading output, and press again to resume
regular rate.
3.3Reverse
Press and hold the Reverse button to change the direction of the Auger (an optional
feature to dislodge obstructions). Release the button to resume spreading.
6/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
3.4Change Solid Material
Press the oval button with “SALT- -” text on it to adjust material type. (Note: Vehicle
must be stationary) Use the left and right arrows to change.
Use the Left and
Right to adjust
Press the oval button
again to confirm and
save the selection.
3.5 Change Liquid Material
Press the oval button with the “LIQUID1” text to adjust the material type. (Note:
vehicle must be stationary)
Use the Left and Right
arrows to adjust.
Press the oval button
again to confirm and
save the selection.
3.6Manual Gate Adjustment
For Manual Gate operation ONLY.
Press the Gate Position Number to select the gate adjustment mode.
Use the up and down
arrows to adjust.
7/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
Press the Gate Position again to verify the selection.
3.7Error Messages
During the operation when an error occurs, a message will appear in the centre of
the screen. Tap anywhere on the message to clear the window.
4 Symbol Actions
All symbols on the right of the screen require a press and hold for >1 seconds.
4.1 Error Log/Diagnostic
When the vehicle is stationary press the ‘Gear’ symbol to display most recent error
messages. If a hydraulic pressure&temperature sensor is connected both readings
will be displayed on the top right of the screen.
Err/Diag Unload USB Bright/Vol Cylinder Lock
8/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
A program key is required to clear the error log; hold the button for >5 seconds.
When a vehicle is moving press the ‘Gear’ symbol to display the real-time status of
spreading.
4.2 UNLOADING
Press the ‘Unload’symbol to enter into unload mode. (Note: The vehicle must be
stationary.)
Turn the dials until
the desired speed is
achieved. Press the
9/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
symbol again and to exit unload mode. Moving the vehicle will suspend the unload
process. It will automatically resume when the truck is stopped again.
4.3 Data Retrieval/Clear Trip Summary
With a ‘LOG DATA KEY’ inserted
Press the ‘USB’symbol to transfer the log data.
With a ‘PROGRAMMING KEY’ inserted
Press the ‘USB’symbol to transfer the parameter. “Transfer Successful” will appear
on the screen momentarily when it finishes.
Without a key inserted
Press the ‘USB’ symbol to clear trip summary.
Note: Displays version 82 or newer ‘PROGRAMMING KEY’ is for programming ONLY
(for older versions ‘PROGRAMMING KEY’ is for both log data and programming).
‘DATA LOG KEY’ is for log data ONLY.
4.4 Brightness and Volume Adjustment
Press the ‘Bright/Vol’symbol to enter into adjustment mode, volume or bright. Press
again to toggle the other mode.
Use the up and down arrows to adjust (only adjustable with vehicle stationary).
10/18
Bosch Rexroth Canada ıJune, 2016 ı Revision 3.0
To adjust volume, the “Vol Adj” needs to be checked on setup user screen.
4.5 Manual Hydraulic Gate Adjustment
For hydraulic gate operation ONLY.
Press the ‘Cylinder’symbol to select the gate adjustment mode. Use the up and
down arrows to adjust.
Press the ‘Cylinder’
symbol again to end
the gate adjustment.
4.6 Programming Mode
Press the ‘Lock’ symbol to enter into programming mode. (Note: A valid
‘PROGRAMMING KEY’ must be inserted into the USB port.)
See Calibration
Manual for
programming details.
Altri manuali per CS 550/150RC
1
Indice
Altri manuali REXROTH Controller per videogiochi
