RF Technology Eclipse2 Manuale utente

Eclipse2

UHF / VHF / 800MHz Base Station

Technical Manual

3 August 2012

Eclipse2 Technical Manual, 3-Aug-12 Page 2 of 17

ist of Associated Publications

Document Number Description

TPR-0308920019 IP Commander User Manual

Disclaimer

Due to our policy of continuous improvement of our pro ucts an services, technical specifications an

claims that were correct at time going to print maybe subject to variation without notice. RF Technology has

en eavoure to ensure that the information in this ocument is correct, but oes not accept liability ue to

typographical, omissions or other errors or subsequent mo ifications of the pro uct.

Specifications may vary from those given in this ocument in accor ance with the requirements of local

regulatory authorities.

All information containe in this manual is the property of RF Technology Pty Lt .

All rights are reserve . This manual may not, in whole or in part, be copie , photocopie , repro uce ,

translate , store , or re uce in any manner without prior written permission.

All tra e names reference are the tra emarks or registere tra emarks of the respective manufacturers.

Users are cautioned that changes or modifications not expressly approved by RF Technologies

could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

RF Technology Pty Limited

Unit 46 / 7 Sefton Road

Thornleigh NSW 2120

Sydney Australia

Phone +61 2 484 1022

Fax +61 2 484 1288

Web www.rftechnology.com.au

Eclipse2 Technical Manual, 3-Aug-12 Page 3 of 17

Contents

CONTENTS ........................................................................................................... 3

INTRODUCTION ..................................................................................................... 6

FEATURES ........................................................................................................... 6

SPECIFICATIONS .................................................................................................... 6

General................................................................................................................................................ 6

Receiver......................................................................................................................................6

Exciter.........................................................................................................................................7

OPERATION .......................................................................................................... 8

Front Panel Controls and Indicators............................................................................................8

Buttons:............................................................................................................................................8

Indicators: ........................................................................................................................................8

Connectors:......................................................................................................................................8

Rear Panel Connectors...............................................................................................................8

System I/O: ......................................................................................................................................8

4 Wire E&M Port...............................................................................................................................9

Ethernet: ........................................................................................................................................10

RF input: ........................................................................................................................................10

RF output:......................................................................................................................................10

RS232 and external reference clock (optional)...............................................................................10

Programming and monitoring .............................................................................................................10

Connecting with Ethernet..........................................................................................................11

Connecting with USB................................................................................................................11

Technical Description .........................................................................................................................11

Control Board............................................................................................................................11

Interface (Main) board...............................................................................................................12

Audio signal processing..................................................................................................................12

I/O and Controls.............................................................................................................................12

Clock generator..............................................................................................................................13

Voltage regulators..........................................................................................................................13

RF modules...............................................................................................................................13

TX module......................................................................................................................................14

RX module.....................................................................................................................................14

Field alignments .................................................................................................................................15

Specifications .....................................................................................................................................15

Description................................................................................................................................15

Channel Capacity...........................................................................................................................15

Sub Audio Signaling.......................................................................................................................15

Eclipse2 Technical Manual, 3-Aug-12 Page 4 of 17

Channel Programming....................................................................................................................16

Channel Selection..........................................................................................................................16

Physical Configuration ..............................................................................................................16

Connectors................................................................................................................................16

Antenna Connector ........................................................................................................................16

Power & I/O Connector...................................................................................................................16

Ethernet Connector........................................................................................................................16

E/M Line Connector........................................................................................................................16

RS232 & External Reference Connector ........................................................................................16

Microphone connector....................................................................................................................16

USB ...............................................................................................................................................16

RF Exposure 17

Eclipse2 Technical Manual, 3-Aug-12 Page 5 of 17

Although there are no dangerous mains voltages present within the equipment,

the following general safety precautions as would normally apply, should be

observed during all phases of operation, service and repair of this equipment.

AROUND THE EQUIPMENT

To minimise any possible shock hazard from an external power supply or

lightning strike, the chassis or equipment cabinet must be connected to an

electrical ground. Provide adequate ventilation around the rear of the

equipment.

DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE

Do not operate the equipment in the presence of flammable gases or fumes.

Operation of any electrical equipment in such an environment constitutes a

definite safety hazard.

DO NOT ATTEMPT INTERNAL SERVICE HILE TRANSMITTING

Thermal or R burns may result from touching certain components within the

power amplifier module while transmitting or operating the transmitter.

DO NOT SUBSTITUTE PARTS OR MODIFY THE EQUIPMENT

Because of the danger of introducing additional hazards, do not install

substitute or lower voltage parts to the equipment. Return to your authorised

distributor.

EXERCISE CAUTION AND CORRECT DISPOSAL OF RF PO ER DEVICES

Most R power transistors and some R power hybrids contain Beryllium Oxide.

Although they are normally safe, if physically damaged toxic dust may be

released. Consult your local authority for correct disposal thereof.

arnings

Eclipse2 Technical Manual, 3-Aug-12 Page 6 of 17

Introduction

The Eclipse2 series is a Base Station designed for Conventional Analogue M and Conventional

APCO P25 modes of operation. Internally, it is driven by software, allowing future firmware

releases to track the development of radio standards and add new modes.

Based on a DSP and RISC platform, the base station has a modular design, which provides

extensive flexibility for users. or example, it may act as a standalone transmitter/receiver, cross-

band repeater, and more. The built-in Ethernet port allows remote monitoring and control of all

operating parameters. Under software control, the centre-frequency can be arbitrarily tuned

across a band, within the limits of the installed receiver and transmitter submodules. A range of

available submodules allows The Eclipse2 system to cover most of the band from 66MHz to

941MHz.

A typical base station or repeater system includes a Reciter (Receiver & Exciter); an R power

amplifier; and a switch mode or linear power supply. All the modules can be plugged into an R

Technology standard 19 inch wide, 4U high, rackframe.

The Reciter can deliver enough R output power to be useful as a point-to-point link, meaning an

external power amplifier may not be required in some configurations. This allows up to six Reciters

to be mounted into a single 19 inch rack.

Features

Specifications

General

Channel Spacing 6.25kHz, 12.5kHz, 25kHz

Reference requency internal, or 5MHz, 10MHz, 12.8MHz external

Monitor speaker output: 3 watts @ 8 ohm

Microphone input: 6 mV RMS @200 ohm

Duty cycle: 100%

Power Supply: +13.8VDC +/-10% (Negative Ground)

Current Drain: 2A Max (with T150A installed with 5 Watt TX output power)

750mA Max with TX O

Operating temperature: -30°C to +60°C

Receiver

requency Spread: see Table 1.

requency Stability: +/-1ppm (-30°C to +60°C)

requency Step: 1Hz

I frequency: 45 MHz

Sensitivity: 12dB SINAD @ -119dBm (0.25uV) R Input

Selectivity: 80dB for 25kHz Channel spacing

75dB for 12.5kHz Channel spacing

Spurious Rejection: 90dB

Intermodulation: 85dB

Modulation acceptance: 7.5kHz for 25kHz Channel spacing

3.75 kHz for 12.5kHz Channel spacing

Eclipse2 Technical Manual, 3-Aug-12 Page 7 of 17

Noise squelch: Adjustable from 0 to 26 dB SINAD

Carrier squelch: Adjustable from –120dbm to –60dBm

Audio Response: 300Hz to 3000Hz

+1/-3dB, lat or 6dB per Octave de-emphasis

Audio Distortion: < 3%

Line output level: -20dbm to +10dbm @600ohm

Auxiliary Audio Output requency Response: 0Hz to 3000Hz

DC offset: 4.6 V

Peak-peak voltage: 7.8V

Table 1: Receiver Module specific specifications

Name of Band Frequency Range

150A 136MHz - 174MHz (VH )

350D 380MHz – 400MHz (UH )

500A 400MHz – 430MHz (UH )

500B 440MHz – 470MHz (UH )

500D 465MHz – 490MHz (UH )

500C 485MHz – 520MHz (UH )

800A 800MHz – 870MHz (UH )

800B 896MHz – 941MHz (UH )

Exciter

requency Spread: see Table 2.

requency Stability: +/-1ppm (-30°C to +60°C)

requency Step: 1Hz

Maximum deviation: 5kHz for 25kHz Channel spacing

2.5kHz for 12.5kHz Channel spacing

Output power: 0.3 Watt to maximum defined in Table 2.

Spurious & harmonics: -36dbm

Hum & Noise: -55dB for 25kHz Channel spacing

-49dB for 12.5 kHz Channel spacing

Audio Response: 300Hz to 3000Hz

+1/-3dB, lat or 6dB per Octave de-emphasis

Audio Distortion: < 3%

Line input level: -20dbm to +10dbm @600ohm

Auxiliary Audio Input requency Response: 0Hz to 3000Hz

Impedance: 100 kΩ

Differential input:

Common mode voltage: 0 V to 2.4 V

Peak-peak voltage: 1.0 V

Single-ended input (AUX IN- floating)

DC offset: 1.2 V

Peak-peak voltage: 2.0 V

Table 2: Exciter Module Specific Specifications

Name of Band Frequency Range Maximum Output Power

(±15%)

150A 136MHz - 174MHz (VH ) 5W

350D 380MHz – 400MHz (UH ) 3W

500A 400MHz – 430MHz (UH ) 3W

500B 440MHz – 470MHz (UH ) 3W

500D 465MHz – 490MHz (UH ) 3W

500C 485MHz – 520MHz (UH ) 3W

800A 800MHz – 870MHz (UH ) 1W

800B 896MHz – 941MHz (UH ) 1W

Note: Notwithstanding the capability of the receiver the software will be modified to ensure

that the reciever will only function in the band approved by the authority responsible for licencing

tne radio.

Note: Notwithstanding the capability of the receiver the software will be modified to ensure

that the exciter will only function in the band approved by the authority responsible for licencing

tne radio.

Eclipse2 Technical Manual, 3-Aug-12 Page 8 of 17

Operation

The Reciter will need approximately 30 seconds to boot up after power up. When the transceiver is

ready to operate, a voice report (if enabled) can be heard from the front panel speaker, and the

Digital/Analog LED will indicate the current operational mode.

Front Panel Controls and Indicators

The front-panel includes LED indicators, tactile switch buttons, a microphone connector and an USB

(type A) connector, refer figure.1 for details

igure1: Eclipse2 Transceiver ront panel

Buttons:

Status – Press this button to listen to the voice report

Test – Press this button to key up the exciter (if front panel test key enabled)

Up – Press this button to increase the speaker volume

Down – Press this button to decrease the speaker volume

Left – Press this button to channel change down

Right – Press this button to channel change up

Reset – The reset switch mounted inside base station, used for reset the Reciter without

power cycle, use a small pin (e.g. paper clipper) to access this switch

Indicators:

Power – This LED (on) indicates that DC power supply is applied to the Reciter

Ethernet – This LED (on) indicates that the transceiver is operating in Digital mode

Analog – This LED (on) indicates that the transceiver is operating in Analog mode, - if the

transceiver is operating in dual mode, both Digital and Analog LED will be on

Tx – This LED (on) indicates the transceiver’s transmitting path is active

Rx – This LED (on) indicates the transceiver’s receiving path is active

Alarm – This LED (flash) indicates the transceiver is in alarm state, press the status button

to listen the alarm information

Connectors:

Microphone – RJ45 connector for front-panel microphone input

USB – USB (type A) connector for connecting a PC via a standard USB cable to monitor or

program the Reciter.

Rear Panel Connectors

System I/O:

The male D shell, 25-pin connector is the main interface to the Reciter Module. The pins of the

connection are described in table 1.

Eclipse2 Technical Manual, 3-Aug-12 Page 9 of 17

Pin No. Description Specification

1, 14 Power supply, positive Input: +13.8VDC

(minimum 10.8V, maximum 16V)

13,25 Power supply, negative Input: Ground

2 System serial bus, Data out Output: +3.3V TTL logic

15 System serial bus, Clock Output: +3.3V TTL logic

3 Exciter PTT input

Input: Low active level

≤

+2.5V)

16 Receiver COS output Output: open collector, Imax = 100mA

4 AUX+ audio input Input: balanced or unbalanced,

100kohm, DC to 3000Hz

17 AUX- audio input Input: balanced or reference voltage

100kohm, DC to 3000Hz

5 AUX+ audio output Output: unbalanced low impedance, DC to 3000Hz

18 AUX- audio output Audio signal ground

6 Line input + Input: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

19 Line input - Input: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

7 Line output + Output: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

20 Line output - Output: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

8 GPS 1 pulse/sec input Input: +3.3V to +15V TTL logic

21 Monitor speaker output Output: unbalanced 8 ohm

300 to 3000Hz, 3 Watt maximum

9 System serial bus, Data in Input: +3.3V TTL logic

22 System serial bus, CS0 Output: +3.3V TTL logic

10 System serial bus, CS1 Output: +3.3V TTL logic

23 T/R relay output Output: open collector, Imax = 100mA

11 External squelch input

Input: Low active (Vin

≤

+2.5V)

24 Spare GPIO input

Input: Low active level

≤

+2.5V)

12 Spare GPIO output Output: open collector, Imax = 100mA

Table1: 25 Pin System I/O Connector signals

4 ire E&M Port

This RJ45 connector provides easy connection to the equipment such as microwave links, the signal

of the E/M line connector described in table2.

Pin No. Description Specification

1 E+ Input: 10V to 48V

2 E- Input: 10V to 48V

3 Line out + Output: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

4 Line out - Output: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

5 Line in + Input: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

6 Line in - Input: balanced 600ohm,

300 to 3000Hz, -20dbm to +10dbm

7 M+ Output: sink current 150mA

8 M- Output: sink current 150mA

Table2: RJ45 E/M Line Connector signals

Eclipse2 Technical Manual, 3-Aug-12 Page 10 of 17

Ethernet:

The RJ45 Ethernet connector is used for networking the base station via IP protocol, a PC can use

this connector to monitor and control the base station locally or remotely.

The Reciter supports the 10/100Mbs specification (defined by IEEE802.3u) and the MDI/MDI-X

auto crossover function which means either a straight though or crossover cable can be used to

connect the base station.

There are two LEDs embedded in the RJ45 Ethernet connector, the green LED indicates that the

Ethernet link is active; the yellow LED indicates TX/RX status between the base station and the

network.

RF input:

The receiver R input connector: 50ohm female, N type.

RF output:

The exciter R output connector: 50ohm female SMA or Optional N type.

RS232 and external reference clock (optional)

The female D shell, 9-pin connector is an optional interface to the transceiver. RS232 and external

reference clock (EXT_RE ) signals share this connector. The pins of the connector are described in

table 3.

Pin No. Description Specification

1 reserved for 1PPS Input

2 reserved for TxD (RS232) Output: +/-5V to +/-15V TTL logic

3 reserved for RxD(RS232) Input: +/-5V to +/-15V TTL logic

4 GND Ground

5 GND(EXT_RE ) Ground

6 GND(1PPS) Ground

7 NC No connection on pin 7

8 GND(RS232) Ground

9 External reference clock Input, sine wave or TTL logic,

Minimum input: 1.5Vp-p

Table2: RJ45 E/M Line Connector signals

Programming and monitoring

Programming and monitoring is accomplished using the IP Commander Software. This software is

based on the Java platform and can be run under various operation systems on the host computer,

it provides a number of useful facilities for the configuration and monitoring of the base station.

The IP Commander software allows configuring of the base station (e.g. the channel frequency,

output power, signal path, etc.) without hardware alignment, it also provides a simple means of

calibrating the R power, RSSI level, audio line levels. or more details of IP Commander software,

please refer the document: RFT Doc No. 0305917801 (IP Commander User Man al).

There are two interfaces which can be used for connecting a computer and the Reciter:

Altri manuali per Eclipse2

Indice

Altri manuali RF Technology Accessori

RF Technology

RF Technology Eclipse2 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente