RGMT DEMOLITION Manuale utente

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

Vol. 1.36 EN DE

DEMOLITION

IM.RGMT.CO

For more details on operating this timepiece

please refer to the enclosed booklet or visit :

MECA-QUARTZ

CHRONOGRAPH WATCH

This watch is powered by a Japanese made

“Meca-Quartz” movement. It combines a battery

regulated engine with a mechanical

chronograph module. The result is a watch

which delivers the meticulous pinpoint

precision of a quartz movement along with the

crisp, ﬂyback handfeel and visual charm of

mechanical watches.

HELIUM

RELEASE

VALVE

SCREW

DOWN

CROWN

UNI-DIRECTIONAL

TURNING BEZEL

1050

2040

1050

2040

MINUTE HAND

DATE

SECOND HAND

HOUR HAND

PUSH

BUTTON A

PUSH

BUTTON B

CHRONOGRAPH

SECOND HAND

CHRONOGRAPH

HOUR HAND

(12 HOUR)

CHRONOGRAPH

MINUTE

HAND

(MOV’T VK63)

PLEASE READ THE FOLLOWING

BEFORE UNSCREWING THE CROWN:

SCREW-DOWN CROWN

Screw-down crowns are used to ensure water

resistance. ALWAYS be certain that your crown is

securely screwed down ( Position [0] is secured.

Positions [1], [2] and [3] are not secured for water

resistance ).

Do NOT unscrew your crown while you are in any

environment where moisture is present.

0 1 2

(1st click) (2nd click)

CLOSED

Securely screwed

+ Water Resistance

OPENED

Not secured

For Water Resistance

USING THE SCREW-DOWN CROWN

DO NOT PULL THE CROWN UNLESS IT IS

FIRST:

NOTE: Failure to SECURELY screw down the crown

after setting the watch may affect its water

resistance.

TO UNSCREW: Turn the

crown anti-clockwise until it

turns freely without tension.

GENTLY pull the crown out to

the other desired positions for

watch setting (see specific

operating instructions on the

following pages).

TO SCREW: Push the crown

ALL THE WAY IN (towards the

watch) THEN begin to turn

clockwise until it is securely

screwed down.

HOW TO SET THE TIME

1. Pull the crown to position [3]-(2nd click).

2. Turn the crown clockwise to set the correct time.

3. Push the crown in.

* Take a.m./p.m. into consideration when setting

the hour and minute hands to the desired time.

*When the crown is at the position [3], do not

press any button, otherwise the chronograph

hands will move.

1. Pull the crown to position [2]-(1st click).

2. Turn the crown clockwise to set the correct date.

3. Push the crown in.

* Do not set the date between 9:00 P.M. and 3:00

A.M. , otherwise the day may not change properly.

If it is necessary to set the date during the time

period, first change the time to any time outside

it, set the date and then reset the correct time.

HOW TO SET THE DATE

USING THE SCREW-DOWN PUSH BUTTON

This watch is equipped with screw-down push

button. The push button will not be able to be

pressed until the button are unscrewed.

To screw-down the button – turn the washer

around the button clockwise until you encounter

resistance.

To unscrew the button – turn the washer around

the button anti-clockwise until it is at its

maximum height away from the case.

You will only be able to operate the functions of the

chronograph when the buttons are unscrewed.

• The watch is only water resistant as marked to its

specified depth if the button has been screwed

down

• Buttons must never be unscrewed or be operated

underwater.

SCREW-

DOWN UNSCREW

STOPWATCH FUNCTION

• The stopwatch can measure up to 12 hours.

STANDARD MEASUREMENT

START STOP RESET

Restart and stop of the stopwatch can be repeated

by pressing the button A.

ACCUMULATED ELAPSED TIME

MEASUREMENT

STOPRESET

START STOP RESTART

Your timepiece is equipped with a Helium Release

Valve.

While this is a very specialized feature that is only

used in certain conditions, the below instructions

should be considered if you are using your watch in

conditions where Helium maybe prevalent at

underwater depths.

While Diving and use in Non-diving condition the

Helium Valve should remain closed and tightly

screwed in flush to the case (Fig 1)

HELIUM VALVE USAGE

(Fig 1)

10 11

HELIUM

RELEASE

VALVE

If while diving the user is exposed to a prolonged

period of exposure to pressurized Helium such as

decompression chamber :

Please allow the Helium release valve to regulate

internal pressure of the timepiece.

Simply unscrew the valve (Fig 2) until Helium

exposure is complete.

Once complete, please close the valve again and also

ensure that the screw down crown is also tightly

secure for maximum protection and water

resistance.

(Fig 2)

1312

STOPWATCH

SECOND HAND

(e.g.) Based on how many seconds it takes a

vehicle to travel 1km or 1 mile (the available

measuring range is up to 60 seconds), the average

speed within the distance can be calculated.

1. Start the chronograph when the vehicles

commence travel.

2. After the vehicle has travelled

1 km/1mile, stop the chronograph.

USING THE TACHYMETER

The most common use of a tachymeter is for

measuring the approximate speed of a vehicle over a

known distance.

Note: The tachymeter indications may appear on

dial ring, rather than on the outer bezel (depending

on model).

As shown in the illustration, it takes the vehicle 45

seconds to travel 1km so the approximate average

speed is 80kph (50 mph).

The approximate average speed within the distance

can be determined by observing the present position

of the second hand and reading the outer bezel.

HOW TO USE A DEPLOYANT CLASP

1. Flip the cover.

2. Press the buttons on the clasp sides.

WATER RESISTANCE

The water resistance indicated on your timepiece serves

only as a guide. Actual water resistance may vary

depending on a number of important factors including

temperature, water salinity, and actual use under water.

The water resistance of your timepiece may eventually be

compromised over time with general wear and tear and

the use of your watch under adverse conditions.

Always remember to employ the screw down crown (if

available) to maintain the water resistance of your

timepiece. Warranty may be voided if the screw down

crown has not been properly employed.

Note that you should NEVER wear your watch in a jacuzzi,

hot shower or steam room where steam may enter the

case despite the watertight seals used to protect your

watch.

The steam may cause condensation inside your watch,

which may affect and damage the inner workings of your

watch – which would also not be covered by the warranty.

HOW TO RESIZE METAL BRACELET

On the inside of the bracelet, you will see some

small arrows engraved on removeable links.

Nylon Head

Hammer

Altri manuali per DEMOLITION

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Manuali Orologio popolari di altre marche

Pandora

Pandora WATCH2 Manuale utente

Casio

Casio QW-4343 Manuale utente

Suunto

Suunto X6 Manuale utente

Seiko

Seiko N830 Manuale utente

MotionX

MotionX 365 Manuale utente

Garmin

Garmin VENU SQ 2 Manuale utente

QCY

QCY Watch GTC Manuale utente

Canyon

Canyon Cindy CNE-KW41WP Manuale utente

Esq

Esq Watches Guida all'installazione

Crane

Crane AA5-CDSM-3A Manuale utente

Timex

Timex W-214 Manuale utente

DETOMASO

DETOMASO MATERA Manuale utente

Geemarc

Geemarc Watch N Shake Manuale utente

LORUS

LORUS W590 Manuale utente

STENLILLE

STENLILLE Actío Manuale utente

Casio

Casio 5594 Manuale utente

Sinn

Sinn HUNTER'S WATCH 3. Edition Manuale utente

Slazenger

Slazenger SLZ800 Manuale utente