Rice Lake CW-90B Manuale utente
CW-90B and CW-90XB
Light-Capacity Bench Scales
Technical Manual
PN 200153 Rev AMay 19, 2020
An ISO 9001 registered company
© Rice Lake Weighing Systems. All rights reserved.
Rice Lake Weighing Systems® is a registered trademark of
Rice Lake Weighing Systems.
All other brand or product names within this publication are trademarks or
registered trademarks of their respective companies.
All information contained within this publication is, to the best of our knowledge, complete and
accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make
changes to the technology, features, specifications and design of the equipment without notice.
The most current version of this publication, software, firmware and all other product
updates can be found on our website:
www.ricelake.com
Contents
© Rice Lake Weighing Systems ● All Rights Reserved i
Contents
Technical training seminars are available through Rice Lake Weighing Systems.
Course descriptions and dates can be viewed at www.ricelake.com/training
or obtained by calling 715-234-9171 and asking for the training department.
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.0 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.2 Leveling the Scale. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.3 Connecting the Load Cell Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.4 Grounding the Scale Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.5 Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.6 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.0 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.4 Load Cell Replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.5 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Introduction
© Rice Lake Weighing Systems ● All Rights Reserved 1
1.0 Introduction
This manual provides reference information to install and wire the CW-90B and CW-90XB Light-Capacity Bench Scales.
Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com
Warranty information can be found on the website at www.ricelake.com/warranties
1.1 Safety
Safety Signal Definitions:
Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in serious injury or death. Includes
hazards that are exposed when guards are removed.
Indicates a potentially hazardous situation that, if not avoided, could result in minor or moderate injury.
Indicates information about procedures that, if not observed, could result in damage to equipment or corruption
to and loss of data.
General Safety
Do not operate or work on this equipment unless this manual has been read and all instructions are understood.
Failure to follow the instructions or heed the warnings could result in injury or death. Contact any Rice Lake
Weighing Systems dealer for replacement manuals.
Failure to heed could result in serious injury or death.
Do not allow minors (children) or inexperienced persons to operate this unit.
Do not operate without all shields and guards in place.
Do not jump on the scale.
Do not use for purposes other then weight taking.
Do not place fingers into slots or possible pinch points.
Do not use any load bearing component that is worn beyond 5% of the original dimension.
Do not use this product if any of the components are cracked.
Do not exceed the rated load limit of the unit.
Do not make alterations or modifications to the unit.
Do not remove or obscure warning labels.
Before opening the unit, ensure the power cord is disconnected from the outlet.
Keep hands, feet and loose clothing away from moving parts.
DANGER
WARNING
CAUTION
IMPORTANT
WARNING
BenchMark CW-90B and CW-90XB
2 Visit our website www.RiceLake.com
2.0 Installation
This section provides an overview of the CW-90B and CW-90XB installation procedure and grounding information.
2.1 Unpacking
Immediately after unpacking, visually inspect the scale to ensure that the unit is undamaged. The shipping carton should
contain the bench scale and this manual. If the bench scale was damaged in shipment, notify Rice Lake Weighing Systems and
the shipper immediately.
2.2 Leveling the Scale
1. Place the scale in the desired location that is reasonably level and free of unnecessary vibrations and air currents.
2. Lift off the scale top cover and locate the level bubble.
3. Adjust the four corner feet on the scale base until the level bubble and all feet contact the support surface so the scale
does not rock.
4. Lock the jam nuts on the feet when the final level is correct.
2.3 Connecting the Load Cell Cable
All models come with 10' or 34'' color-coded load cell cable.
Do not cut this cable. Cutting this cable voids the warranty.
See the indicator manual to determine the proper load cell cable input connectors. Use the following color codes to
wire the load cell cable to the indicator.
Connect Sense and Excitation wires together if using 4-wire system without sense leads.
IMPORTANT
Note
Color Code Function
Green + Excitation
Black - Excitation
Blue + Sense
Brown - Sense
Red + Signal
White - Signal
Table 2-1. CW-90B Load Cell Wiring - 6 Wire
Color Code Function
Green + Sense
Black - Excitation
Blue + Excitation
Red - Signal
White + Signal
Grey - Sense
Table 2-2. CW-90XB Load Cell Wiring - 6 Wire
Note
Installation
© Rice Lake Weighing Systems ● All Rights Reserved 3
2.4 Grounding the Scale Base
The CW-90B and CW-90XB can build up static electricity charge during weighing operations. If powerful enough, the charge
can travel through the load cell cable to the indicator. The unit should be adequately grounded so static charges and transient
electrical surges can drain directly to the ground.
A chassis ground screw is located on the bottom of the platform. Within the replacement parts tables in Section 2.6 on page 4
the 8-32 NCx3/16 screw is used to facilitate grounding. Use a ground wire of at least 18 gauge copper to connect this screw to
the same earth ground as the attached indicator.
2.5 Calibration
It is recommended that the scale be exercised by loading it to near capacity two or three times before calibration to ensure
everything is seated. See the specific indicator manual for the proper calibration procedure.
To calibrate, see the following procedure:
1. With no load on scale, place the indicator in its calibration mode and perform a zero calibration.
2. Place certified calibration weights on platform equal to 70%–100% of scale’s capacity. If several weights are used,
distribute them evenly around the platform.
3. Perform a calibration.
4. Remove certified calibration weights and check the zero reading. If necessary, repeat the calibration process.
See the indicator manual for the specific indicator calibration procedure.
Note
Installation
© Rice Lake Weighing Systems ● All Rights Reserved 5
Item No. Part No. Description Qty.
1 107144 Top Cover, 10 x 10 1
2 107140 Spider Plate, 10 x 10 1
3 105555 Nut, 1/4-20NC 8
4 106462 Screw Cap, 1/4 -20NC, Hex Head 4
5 107756 Load Cell, SPT RL1040, 34'' Cable, 5 lb Scale CW-90B 1
107757 Load Cell, SPT RL1040, 34'' Cable, 10 lb Scale CW-90B
107758 Load Cell, SPT RL1040, 34'' Cable, 25 lb Scale CW-90B
32860 Load Cell, SPT RL1040, 10' Cable, 5 lb Scale CW-90B
32861 Load Cell, SPT RL1040, 10' Cable, 10 lb Scale CW-90B
32864 Load Cell, SPT RL1040, 10' Cable, 25 lb Scale CW-90B
6 105452 Base Plate, 10 x 10 1
7 45329 Screw, 8-32NC x 3/16 1
8 107476 Foot, 1/4 - 20NC 4
9 52383 Load Cell Shim .25 x 1 x 1.34 SST 1
10 15148 Washer, Lock 1/4 Regular 4
11 14963 Screw, Cap 1/4-20NC x 3/4 Hex Head SST 2
12 15410 Level, Spirit Bubble Plastic 1
13 21948 Screw, Cap 1/4-20NC x 5/9 Hex Head SST 2
14 35082 Shim, Load Cell .125 x 1 x 1.34 SST 1
15 163794 Cap, Screw 1/4-28NF x 1/2, Flat Head SST 1
Table 2-3. CW-90B 10' x 10' Parts List
Item No. Part No. Description Qty.
1 105457 Top Cover, 12 x 12 1
2 105450 Spider Plate, 12 x 12 1
3 105555 Nut, 1/4-20NC 8
4 106462 Screw Cap, 1/4 -20NC, Hex Head 4
5 107758 Load Cell, SPT RL1040, 34'' Cable, 25 lb Scale CW-90B 1
107759 Load Cell, SPT RL1040, 34'' Cable, 50 lb Scale CW-90B
107760 Load Cell, SPT RL1040, 34'' Cable, 100 lb Scale CW-90B
32864 Load Cell, SPT RL1040, 10' Cable, 25 lb Scale CW-90B
32865 Load Cell, SPT RL1040, 10' Cable, 50 lb Scale CW-90B
32866 Load Cell, SPT RL1040, 10' Cable, 100 lb Scale CW-90B
6 105452 Base Plate, 12 x 12 1
7 45329 Screw, 8-32NC x 3/16 1
8 107476 Foot, 1/4 - 20NC 4
9 52383 Load Cell Shim .25 x 1 x 1.34 SST 1
10 15148 Washer, Lock 1/4 Regular 4
11 14963 Screw, Cap 1/4-20NC x 3/4 Hex Head SST 2
12 15410 Level, Spirit Bubble Plastic 1
13 21948 Screw, Cap 1/4-20NC x 5/9 Hex Head SST 2
14 35082 Shim, Load Cell .125 x 1 x 1.34 SST 1
15 163794 Cap, Screw 1/4-28NF x 1/2, Flat Head SST 1
Table 2-4. CW-90B 12' x 12' Parts List
BenchMark CW-90B and CW-90XB
6 Visit our website www.RiceLake.com
Item No. Part No. Description Qty.
1 107144 Top Cover, 10 x 10 1
2 107140 Spider Plate, 10 x 10 1
3 105555 Nut, 1/4-20NC 8
4 106462 Screw Cap, 1/4 -20NC, Hex Head 4
5 107174 Load Cell, SPT RLPWM15HE, 34'' Cable, 5 lb and 10 lb Scales CW-90XB 1
107175 Load Cell, SPT RLPWM15HE, 34'' Cable, 25 lb Scale CW-90XB
108685 Load Cell, SPT RLPWM15HE, 10' Cable, 5 lb and 10 lb Scales CW-90XB
108686 Load Cell, SPT RLPWM15HE, 10' Cable, 25 lb Scale CW-90XB
6 105452 Base Plate, 10 x 10 1
7 45329 Screw, 8-32NC x 3/16 1
8 107476 Foot, 1/4 - 20NC 4
9 52383 Load Cell Shim .25 x 1 x 1.34 SST 1
10 15148 Washer, Lock 1/4 Regular 4
11 14963 Screw, Cap 1/4-20NC x 3/4 Hex Head SST 2
12 15410 Level, Spirit Bubble Plastic 1
13 21948 Screw, Cap 1/4-20NC x 5/9 Hex Head SST 2
14 35082 Shim, Load Cell .125 x 1 x 1.34 SST 1
15 163794 Cap, Screw 1/4-28NF x 1/2, Flat Head SST 1
Table 2-5. CW-90XB 10' x 10' Parts List
Item No. Part No. Description Qty.
1 105457 Top Cover, 12 x 12 1
2 105450 Spider Plate, 12 x 12 1
3 105555 Nut, 1/4-20NC 8
4 106462 Screw Cap, 1/4 -20NC, Hex Head 4
5 107175 Load Cell, SPT RLPWM15HE, 34'' Cable, 25 lb Scale CW-90XB 1
107176 Load Cell, SPT RLPWM15HE, 34'' Cable, 50 lb Scale CW-90XB
107177 Load Cell, SPT RLPWM15HE, 34'' Cable, 100 lb Scale CW-90XB
108686 Load Cell, SPT RLPWM15HE, 10' Cable, 25 lb Scale CW-90XB
108687 Load Cell, SPT RLPWM15HE, 10' Cable, 50 lb Scale CW-90XB
108688 Load Cell, SPT RLPWM15HE, 10' Cable, 100 lb Scale CW-90XB
6 105452 Base Plate, 12 x 12 1
7 45329 Screw, 8-32NC x 3/16 1
8 107476 Foot, 1/4 - 20NC 4
9 52383 Load Cell Shim .25 x 1 x 1.34 SST 1
10 15148 Washer, Lock 1/4 Regular 4
11 14963 Screw, Cap 1/4-20NC x 3/4 Hex Head SST 2
12 15410 Level, Spirit Bubble Plastic 1
13 21948 Screw, Cap 1/4-20NC x 5/9 Hex Head SST 2
14 35082 Shim, Load Cell .125 x 1 x 1.34 SST 1
15 163794 Cap, Screw 1/4-28NF x 1/2, Flat Head SST 1
Table 2-6. CW-90XB 12' x 12' Parts List
Altri manuali per CW-90B
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Rice Lake Scala
Rice Lake
Rice Lake Digi DC-788 Manuale utente
Rice Lake
Rice Lake RL-TA Series Manuale utente
Rice Lake
Rice Lake BenchMark HE-X Manuale utente
Rice Lake
Rice Lake 102613 Istruzioni per l'installazione
Rice Lake
Rice Lake Survivor RT Guida
Rice Lake
Rice Lake RL-330 Series Manuale utente
Rice Lake
Rice Lake 350-10 Series Manuale utente
Rice Lake
Rice Lake 250-10-4 Series Manuale utente
Rice Lake
Rice Lake SURVIVOR Advantage Series Manuale utente
Rice Lake
Rice Lake 350-10-8S Manuale utente
Rice Lake
Rice Lake CW-90 Manuale utente
Rice Lake
Rice Lake Retail Series Manuale per l'uso e la cura
Rice Lake
Rice Lake OS-10 Manuale
Rice Lake
Rice Lake 120 Manuale utente
Rice Lake
Rice Lake TuffSeal JB4ES Manuale utente
Rice Lake
Rice Lake RL-DBS Istruzioni operative
Rice Lake
Rice Lake 350-10-3 Manuale utente
Rice Lake
Rice Lake IQ6200 Manuale utente
Rice Lake
Rice Lake CLS Series Manuale utente
Rice Lake
Rice Lake 340-10 Series Istruzioni operative
