Rice Lake RoughDeck CC Caster Cargo Manuale utente

RoughDeck® CC

Caster Cargo Scale with EZ Mount Load Cell Kits

and a TuffSeal® Junction Box

Installation Manual

PN 203881 Rev B

September 20, 2021

An ISO 9001 registered company

Rice Lake Weighing Systems® is a registered trademark of

Rice Lake Weighing Systems.

All other brand or product names within this publication are trademarks or registered

trademarks of their respective companies.

All information contained within this publication is, to the best of our knowledge, complete and

accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make

changes to the technology, features, specifications and design of the equipment without

notice.

The most current version of this publication, software, firmware and all other product updates

can be found on our website:

www.ricelake.com

Contents

Technical training seminars are available through Rice Lake Weighing Systems.

Course descriptions and dates can be viewed at www.ricelake.com/training

or obtained by calling 715-234-9171 and asking for the training department.

1.0 Introduction ....................................................................................... 1

1.1 Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.0 Mechanical Installation ..................................................................... 3

2.1 General Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Mount Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.0 Load Cell Wiring ................................................................................ 6

4.0 TuffSeal Junction Box ...................................................................... 7

4.1 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.2 Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.3 Junction Box Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4.3.1 Connect Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

4.4 Trimming Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4.4.1 Signal Board Trimming Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5.0 Calibration........................................................................................ 13

6.0 Troubleshooting .............................................................................. 14

7.0 Replacement Parts .......................................................................... 15

7.1 EZ Mount 1 Weigh Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

7.2 TuffSeal JB4SS Junction Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

RoughDeck CC

ii Visit our website www.RiceLake.com

Rice Lake continually offers web-based video training on a growing selection

of product-related topics at no cost. Visit www.ricelake.com/webinars.

Introduction

1.0 Introduction

The installation should be planned by a qualified structural engineer.

Each installation is unique, this manual is meant to serve as a general guideline for installation.

Manuals and additional resources are available from the Rice Lake Weighing

Systems website at www.ricelake.com

Warranty information can be found on the website at www.ricelake.com/warranties

The RoughDeck CC Caster Cargo Scale has a 20,000 lb capacity with a powder coat surface

for durability. Load and unload the caster deck scale in all directions with 360 degree swivel

casters (108 Kalpar Casters model DL55014893).

The EZ Mount kits provide an extremely accurate method for weighing medium and large

capacity structures that are subject to large thermal expansion/contraction or vibration forces.

The design uses a double ended shear beam load cell (700 Ω bridge) and transmits the load

with a sliding pin on the load-bearing groove of the cell. This design is very effective in

providing for thermal expansion/contraction with little friction.

Figure 1-1. Thermal Expansion

In the majority of applications, the assemblies are self-checking and held captive with no need

for check or stay rods, making this mount a good choice for areas with frequent seismic activity.

The sliding pin design eases load cell installation and replacement without the need to raise the

structure a large amount.

The RoughDeck CC uses four stainless steel EZ Mount 1 weigh modules (Section 2.2 on page 4)

containing 10,000 lb stainless steel IP67 load cells (RL70000SS).

The RoughDeck CC also utilizes a JB4SS TuffSeal NEMA Type 4X stainless steel signal trim

junction box. The TuffSeal junction box can be placed in any of the corners of the caster deck

(Section 4.2 on page 8) and accessed through any of the 4 removable deck panels along with

the load cells and mounts.

Thermal

Expansion

RoughDeck CC

2 Visit our website www.RiceLake.com

1.1 Safety

Safety Signal Definitions:

Indicates an imminently hazardous situation that, if not avoided, will result in

death or serious injury. Includes hazards that are exposed when guards are

removed.

Indicates a potentially hazardous situation that, if not avoided could result in

serious injury or death. Includes hazards that are exposed when guards are

removed.

Indicates a potentially hazardous situation that, if not avoided, could result in

minor or moderate injury.

Indicates information about procedures that, if not observed, could result in

damage to equipment or corruption to and loss of data.

General Safety

Do not operate or work on this equipment unless this manual has been read and

all instructions are understood. Contact any Rice Lake Weighing Systems

dealer for replacement manuals.

Failure to heed may result in serious injury or death.

Do not use for purposes other than weight measurement.

Do not use any load-bearing component that is worn beyond 5% of the original dimension.

Do not use this product if any of the components are cracked.

Do not exceed the rated load limit of the unit.

Do not make alterations or modifications to the unit.

Do not use without the deck completely assembled.

Do not place fingers into slots or possible pinch points.

DANGER

WARNING

CAUTION

IMPORTANT

WARNING

Mechanical Installation

2.0 Mechanical Installation

This section provides an overview of mechanical installation information.

2.1 General Installation Guidelines

The RoughDeck CC system uses four EZ mounts. EZ mounts come assembled to the mount

risers with wooden blocks to keep the load cell from being loaded during shipping.

Figure 2-1. EZ Mount Assemblies

The mounting surface for the mounts must be level within ±0.5°.

If the mounting surfaces are not level, use shims and/or grout to level the mount.

If possible, check that the mount is level when the structure is fully loaded because excessive

deflections in legs and supporting structures may cause additional side forces, which affect

accuracy. Deflection of the mounts top or base plate due to loading should not exceed ±0.5°.

The load on each mount assembly should vary by no more than 20%.

Add shims where necessary to achieve correct load distribution.

During installation, avoid overload damage to the load cells.

Note

WARNING

RoughDeck CC

4 Visit our website www.RiceLake.com

2.2 Mount Installation

Secure an EZ Mount assembly to the riser mount plate in each corner of the caster deck. The

access panel top plate and corner caster plate need to be removed to access the mounting

holes to secure the EZ Mount assemblies.

Figure 2-2. EZ Mount Assembly Installation

EZ Mount Orientation

Position EZ Mount assemblies so the load cell cables are positioned on the inside.

Figure 2-3. Load Cell Orientation

The arrow on the load cell should point in the direction of the load.

Access Panel

Top Plate

Corner

Caster Plate

Riser Mount

Plate

Mount Riser

EZ Mount

Note

Mechanical Installation

Secure the EZ Mount Base Plate

Verify that there is no initial misalignment and that the load cells are in the center of the hole in

the top plate loading bracket. Relocate if necessary.

Attach the base plates to the foundation using suitable anchors for concrete or by bolting or

welding to a steel structure.

Verify that the base plates are no more than ±0.5° out of level. Shim if necessary and

fully tighten mounting bolts.

Verify bolts securing the load cell to the base plate are tight. Only torque load cell

bolts to 20 foot-pounds. This allows the double-ended load cell to flex under load.

If surrounding equipment is frequently steam cleaned, or if the load cell is subjected to direct

washdown, a protective shroud for the weighing assembly is recommended.

Proper drainage is necessary so the weighing assembly is not standing in water. All support

points should be equally stiff so that they deflect by the same amount as the structure is loaded.

Figure 2-4. EZ Mount Parts Illustration

Note

Top Plate

Loading Bracket

Cotter Pin

Load Cell Bolt

Load Cell

Base Plate

Load Pin

Locating Pin

Washer

Load Bar

RoughDeck CC

6 Visit our website www.RiceLake.com

3.0 Load Cell Wiring

This section provides an overview of load cell wiring information.

1. Route the load cell cables so they will not be damaged or cut. Cable should not be routed

near heat sources greater than 150°F. Do not shorten any load cell cable. The load cell is

temperature compensated with the supplied length of cable. Cutting the cable will affect

temperature compensation. Coil and protect excess cable so it will not be mechanically

damaged or be sitting in water.

2. Provide a drip loop in all cables so that water or other liquids will not run directly down the

cables onto either the load cells or the junction box.

Figure 3-1. Drip Loop

If conduit protection is necessary against mechanical or rodent damage to the load

cell cables, use flexible conduit and conduit adapters at the load cells.

Conduit can also provide protection against moisture ingress into the load cell.

3. Connect cables for RL70000SS load cells to the summing board in the junction box

according to Table 3-1 and the labels on terminal strips of the junction box.

To verify the wiring scheme, see the certification shipped with each load cell.

Wire Color Signal

Red + Excitation

Black – Excitation

Green + Signal

White – Signal

Gray or Bare Shield

Table 3-1. Load Cell Wiring

Drip Loop

Note

Indice

Altri manuali Rice Lake Scala

Rice Lake

Rice Lake 181881 Manuale utente

Rice Lake

Rice Lake RL-MCS-LB Manuale utente

Rice Lake

Rice Lake Benchmark LP Manuale utente

Rice Lake

Rice Lake RL-HPJ Manuale

Rice Lake

Rice Lake D400 Manuale utente

Rice Lake

Rice Lake CLS-M Manuale utente

Rice Lake

Rice Lake VS-10 Manuale utente

Rice Lake

Rice Lake RL-DBS Istruzioni operative

Rice Lake

Rice Lake RL-MPS-50 Manuale utente

Rice Lake

Rice Lake 540-10 Series Manuale utente

Rice Lake

Rice Lake Summit SB-1000 Manuale utente

Rice Lake

Rice Lake 140-10-7N Series Manuale utente

Rice Lake

Rice Lake ISHIDA IP-AI Manuale utente

Rice Lake

Rice Lake SURVIVOR ATV series Manuale utente

Rice Lake

Rice Lake RL-MPS-40 Manuale utente

Rice Lake

Rice Lake TS Series Manuale utente

Rice Lake

Rice Lake 350-10-3 Manuale utente

Rice Lake

Rice Lake Load Ranger Manuale utente

Rice Lake

Rice Lake 260-10-1 Manuale utente

Rice Lake

Rice Lake RL-MCS Manuale utente

Rice Lake

Rice Lake RoughDeck Manuale utente

Rice Lake

Rice Lake 112566 Manuale utente

Rice Lake

Rice Lake 150-10-7 Manuale utente

Rice Lake

Rice Lake MSI-4260M Manuale utente

Manuali Scala popolari di altre marche

AWS

AWS ZEO-50 Manuale utente

Gima

Gima Glass Body Fat Analyzer Manuale elenco delle parti

Seca

Seca 374 Manuale utente

TEC

TEC TEC SL59 SERIES Manuale utente

Axis

Axis B/E Series Manuale utente

Alecto

Alecto ACW-40 Manuale utente

IKA

IKA RCT basic safety control Manuale utente

ADE

ADE M20011 Manuale utente

Duronic

Duronic KS3000 Manuale utente

Digi

Digi SM-720 Manuale utente

Cardinal

Cardinal CS Series Manuale utente

Korona

Korona Kastella Manuale utente

A&D

A&D FC-50Ki Manuale utente

BDA

BDA CAMARGUE Manuale utente

Tanita

Tanita HD-357 Manuale utente

Leifheit

Leifheit 03173 Manuale utente

Lumme

Lumme LU-1340 Manuale utente

Fidelity Electronics

Fidelity Electronics G2e Manuale utente