Richmond GTR211 Manuale utente
GTR211 Installation Manual: Rev 1 1
Sliding Gate Opener
User Manual GTR211
WARNING
Instructions must be read before beginning installation. Please follow these instructions carefully, incorrect installation could
aect gate operation. If you require more information, please contact your local Richmond Wheel & Castor Co branch.
AU: 1300 474 246 NZ: 0800 61 71 81 International: +613 9551 2233
For installation or troubleshooting assistance visit gatesupport.richmondau.com
When mounting and positioning the motor ensure that the power cable is unplugged. The motor cover will need to be removed to mount
the motor to the mounting plate. Any changes to the settings of the gate motor can only be made by a licensed electrician.
Please Note: This motor is AC 240V Power only and is not compatible with DC Battery Backup or Solar power.
Gate in closed position Gate in open position
Viewed from inside the property
GTR211 Installation Manual: Rev 1 2
Optional Accessories Available:
Additional Remotes (GTR179): Spare/Additional remotes for the automatic gate kit, these will
need to be paired to the motor.
Reective Photocells (GTR208): Increase safety during opening/closing by preventing gates
from closing on vehicles/pedestrians.
Exit Wand (GTR147): Senses cars or trucks moving at more than 8km per hour and opens the
gate without the need for using a remote or keypad.
Wireless Keypad (GTR180): Allows secure access through the gate used with a user set code.
Wired Keypad (GTR055): Allows secure access through the gate used with a user set code.
Wireless Push Button (GTR201): Allows access through the gate at the push of a button.
Hard Wire Push Button (GTR202): Allows access through the gate at the push of a button.
External Remote Receiver (GTR197): Allows the pairing of extra remotes. Up to 250 extra re-
motes can be paired with this accessory.
Please refer to the relevant manual for each accessory for instructions on wiring
them to the GTR211 gate motor.
GTR211 Installation Manual: Rev 1 3
Contents:
Gate Opening Default Setting Information 4
General Safety 5
Parts List 6
Technical Specications 7
Motor Installation
Before you start 8
Tools Required / Example Sliding Gate Setup 9
Step 1 – Gate Preparation Before Adding Your Motor 10
Step 2 – Motor Pad Footing 10
Step 3 - Motor Position Installation 11
Step 4 - Removing the Motor Cover for Mounting 12
Step 5 – Drilling Holes for Anchor Bolts 12
Step 6 – Fitting the Mounting Plate & Motor 13
Step 7 – Gear Rack & Motor Alignment 14
Step 8 – Limit Travel Stops 16
Step 9 – Powering the Motor 18
Step 10 – Testing the Limit Travel Stops 19
Programming and Wiring
Control Board Diagrams 20
Dip Switch Adjustment 22
Further Settings and Programming 23-25
Troubleshooting 26
Maintenance 27
Clearing and Pairing Remotes 28
Additional instructions for connecting accessories to this
motor can be found in the manuals for each accessory.
GTR211 Installation Manual: Rev 1 4
Gate Opening Default Setting Information:
The gate motor will open the gate to the right-hand side as its default setting (refer to g 1).
Default operation:
Motor mounted on the right-hand side
Left-Hand Opening:
Motor mounted on the left-hand side
Fig 01
Fig 02
Before Installing: Test the motor by plugging it into a power source and pressing the remote. You will see the motor cog turn. When it
stops (after approx 1 minute), press the remote again to see it turn in the opposite direction. This will give you an understanding of the
way in which the motor will move the gate.
If your gate needs to open from the other direction (to the left, refer to g 2) your motor needs to be mounted on the left-hand
side as shown below, you will need to switch DIP SWITCH 5 from OFF to ON (refer to page 23) and swap over the CL & OP
wires in J10 terminal (refer to g 31 on page 20)
Press the rst/top button
on the remote.
Note: Ensure that the motor is unplugged before proceeding with installation.
Please keep ngers away from the motor cog whilst it is turning.
Any works done to the motor must be completed whilst the power is o and the motor is unplugged
The motor cog will turn counter-clockwise,
moving the gate frame.
The gate will then move in the set
direction. Default: right-hand open.
GTR211 Installation Manual: Rev 1 5
Thank you for choosing this sliding gate opener. Please read the manual carefully before assembling and using
the opener. Do not leave out the manual if you send this product to a third party. This product complies with the
recognised technical standards and safety regulations. Our company has the right to change this manual without
prior notice.
General Safety:
Warning: Incorrect or improper use of this product can cause damage to persons,
animals or properties.
• Please ensure that the input voltage to the low voltage power supply used matches with the supply voltage of
gate opener (AC240V 50Hz).
• All modications to wiring or electrics, and any adjustment or maintenance to 240VAC MUST be performed by
a qualied electrician.
• To avoid damaging gas, power or other underground utility lines, contact the relevant authority BEFORE
commencing any digging.
• All potential hazards and exposed pinch points of the gate must be eliminated or guarded prior to installation of
this gate motor.
• Never mount any device that operates the gate motor where the user can reach over, under, around or through
the gate to operate the controls. These must be placed at least 1.8m from any moving part of the moving gate.
• Ensure power plug is disconnected from the power socket during installation or maintenance.
• Keep remote control and other control devices out of children’s reach, in order to avoid unintentional activation.
• Never allow anyone to hang onto the gate while moving.
• Please ensure the warning sign provided is tted to the gate.
• If required, install infrared photocells (GTR208, sold separately) to detect obstructions and prevent injury or
damage.
• To ensure safety, before installing the main motor, mount a Gate End Stop (GTR017) and a Gate Stopper
(GTR017 or GTR018) at each end of the rail to prevent the gate travelling o the track.
• Instruct all users about the control systems provided and the manual opening operation in case of emergency.
• Ensure that the power cable is connected to a RCD protected weatherproof power outlet that has been installed
by a qualied electrician.
• Do not install the product in an explosive atmosphere or where there is any danger of ooding.
• This product was exclusively designed and manufactured for the use specied in the present documentation.
Any other use not specied in this documentation could damage the product and be dangerous.
• Only use original parts for any maintenance or repair operation. Richmond Wheel & Castor Co declines all
responsibility with respect to the automation safety and correct operation when other supplier’s components are
used.
• Do not modify the automation components, unless explicitly authorised by Richmond Wheel & Castor Co.
• The user must avoid any attempt to carry out any works or repairs on the motor, and should always request the
assistance of qualied personnel.
• This motor is suitable for use on one sliding gate only.
• Anything which is not expressly provided for in these instructions is not allowed and will void warranty.
• Dispose of all packing materials (plastic, cardboard, polystyrene etc.) according to current guidelines.
Keep plastic bags and polystyrene out of children’s reach.
Please save these instructions for future use.
GTR211 Installation Manual: Rev 1 6
Parts List:
No. Picture Name Quantity
1Main motor 1
2Motor Mounting Plate 1
3
Manual Release Keys
(These keys are needed during power
outage, keep on hand)
2
4Remote Controls
(factory paired to motor) 2
5Gate Warning Signage
(Must be Fitted to Gate) 1
6In the accessories box you will nd
the items below: 1
6a Limit travel stops
(left hand & right hand) 2
6b Limit travel stop mounting screw
M6x18 4
6c Masonry Anchor bolt M12x100mm
(Drill bit size: M12 Masonry) 4
6d Motor mounting set screws M10 x
50mm, spring & flat washers 4
GTR211 Installation Manual: Rev 1 7
Technical Specications:
Model GTR211
Power supply 240VAC/50Hz
Motor power 550W
Gate moving speed 11-13m/min
Maximum weight of gate 1500kg
Remote control distance Up to 30m
Remote control mode Single button mode
Limit switch Spring limit switch
Noise Up to 60dB
Working duty S2, 20min (20 minutes continuous operation)
IP Rating IP54
Maximum Remote
Controls to be paired 25
Frequency 433.92 MHz
Working temperature -20°C ~ +70°C
Fig 03
GTR211 Installation Manual: Rev 1 8
Motor Installation:
Before you start
• The GTR211 Sliding Gate Motor is suitable for powering the opening and closing motion of gates up to
1500kg in weight, up to a length of 12m.
• Gate motion is achieved by the rotating cog of the gate motor driving the gear rack tted to the moving
gate (GTR092, sold separately).
• The gate motor requires you to press the remote control once to open, and once again to close. This is
a safety feature to ensure safe operation.
• The gate motor itself must be tted within private property, never externally to a property’s boundary.
Power Supply: The GTR211 requires 1 x 10Amp AC240V 50Hz power supply (RCD Protected Weatherproof
PowerPoint). The GTR211 comes complete with a power lead and plug that is 1m long. If you do not have
a suitable RCD protected weatherproof power point within 1m of the gate motor you will need to consult a
licenced electrician.
Any works done to the motor must be completed whilst the power is o and the
motor is unplugged.
Any modications/alterations/works to the 240V AC power components must only be
completed by a licensed electrician for your state/country.
Please Note:
Your weatherproof power outlet should be no more than 1m from the
electric gate motor.
If your weatherproof power outlet is more than 1m from the gate motor,
you will require a licensed electrician to t a new power cable.
Any excess cable length should be cable tied and secured out of the
way of moving objects.
GTR211 Installation Manual: Rev 1 9
For Installing Your Gate Motor, You Will Need:
• Power drill
• Tape measure
• Level
• 12mm Masonry Drill Bit (for the 4 motor masonry anchor bolts)
• Socket and Spanner Set
• Phillips Head Screwdriver
Example Sliding Gate Setup:
If you require any gate hardware, contact Richmond Wheel & Castor Co or an authorised reseller.
Gate Track and
Track Wheels
Gate Guide
Rollers
Gate End
Catch
Gate
Stopper
GTR211 Installation Manual: Rev 1 10
Step 1 - Gate Preparation Before Adding
Your Sliding Gate Motor:
• Ensure that the sliding gate is correctly installed.
• The gate is horizontal and level and the gate can glide back and forth smoothly when moved
by hand before installing the Automatic Gate Opener.
• Wheels and guide rollers should rotate easily and be free from dirt/grime.
• Track should be at, level and rmly axed.
• Any misalignment in the gate will aect performance of the automatic gate opener.
The gate should slide smoothly by hand before attempting to install the gate opener.
Please ensure that the motor power cable is not plugged in at any stage before Step 9
Step 2 - Motor Pad Footing (Minimum Requirement):
• The motor pad concrete footing requires an area of no less than 450mm long x 300mm wide
and a minimum depth of 200mm (Standard requirement).
• Ensure surface is level and parallel to the driveway
Mounting Plate Dimensions:
Indice
Altri manuali Richmond Apricancello
Richmond
Richmond GTR502 Manuale utente
Richmond
Richmond GTR064 Manuale utente
Richmond
Richmond GTR064 Manuale utente
Richmond
Richmond GTR058 Manuale utente
Richmond
Richmond GTR156 Manuale utente
Richmond
Richmond GTR500 Manuale utente
Richmond
Richmond GTR099 Manuale utente
Richmond
Richmond GTR181 Manuale utente
Richmond
Richmond GTR058 Manuale utente
Richmond
Richmond GTR058 Manuale utente
