Ricoh MP7240A Manuale utente

To view this manual, use following browsers
Microsoft Internet Explorer 4 or later
Netscape Communicator 4 or later
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not 
occur in a particular installlation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. 
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an 
experienced radio / TV technician for help. 
Warning as to USE
This CD-R/RW drive together with software is a product for utilizing CD-R/RW recording media with rewriting, erasing and readout 
capabilities, as an external computer memory device. Except in the case where copying of CD-ROMs or the like is especially 
recognized under the copyrights laws as being for the purpose of individual use by the customer or the like, or in the case where 
the customer has obtained permission to make copies from the rightholder, reproduction of CD-ROMs and copyright laws. Take 
notice that unauthorized copying may be subject to claims for damages and to penalties.
CAUTION
Rating voltage for peripherals.
1. Headphone Jack Rating Voltage output Audio Signal Max. 2V

FCC WARNING

Changes or modification not expressly approved by the party responsible for compliance could void the user's authority to operate

the equipment.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation

exposure.

Akustischer Geräuschpegel

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation

exposure.

Dieser Druckerüberschreitet einen Geräuschpegel von 70 dB (A) während dem Betrieb nicht.

Declaration of Conformity

"The Product complies with the requirements of the EMC Directive 89/366/EEC and the Low Voltage Directive 73/23/EEC."

●Please take notice that the manufacturer of this equipment does not offer any warranty against data loss due to

inappropriate installation or handling, or direct or indirect damages.

●Please take notice that the manufacturer will bear no responsibility for direct or indirect damages caused by the use of

this product or its malfunction.

●Please take notice that the manufacturer will bear no responsibility for damage to data caused by this product.

●Please backup (copy) all important data as protection against data loss.

●PC DOS is a trademark of IBM Inc.

●MS-DOS, Windows, Windows ® 95, Windows ® 98, Windows NT®, Windows® 2000 and Windows® XP are trademarks registered

in the United States and other countries by the Microsoft Corporation.

●

●Acrobat reader is trademark of Adobe Inc.

●The company names and product names written in this manual are trademarks or registered trademarks.

This manual uses the following symbols to indicate important information relating to the drive.

Failing to comply with the information in this manual and/or incorrect handling of the drive may result

in serious personal injury or damage to the product.

Indicates restriction or precaution that should be observed.

Provides useful additional information.

This manual contains important notes and product handling information. Be sure to read the manual

before using the product. For easy reference in the future, please keep the manual at a handy

location.

Multimedia Printer series

Thank you for purchasing the Multimedia Printer series drive (hereafter referred to as the drive). The drive enables you to play

CD-ROM discs, write once and play CD-R discs, or write, play, and rewrite CD-RW discs.

The following marks indicate media that can be used with the drive.

A new technology called Just Link, that overcomes buffer underrun

problems

Buffer underrun errors which occur when data transfer falls behind the writing operation has been inevitable for CD-R/RW

drives. Just Link, which we at Ricoh developed on our own, is a new technology that predicts possible occurrences of buffer

underrun errors in advance and automatically avoids them. With this technology, the drive ensures stable writing operation even

under circumstances where buffer underrun errors tend to occur with conventional drives.

New technology: JustSpeed (Optimum Write Speed Control) function

When the write speed of 24X is specified, this function checks the media's capability to see if it can be written at above-12X

speeds. If the media is not capable of such speeds, the write speed is reduced to 20x, 16X or 12X.

Obey the following cautions when handling the drive or discs.

Cautions During Installation

●Install the drive in accordance with the specifications. Be careful to avoid locations likely to cause vibration or shock.

●Avoid locations where there is high humidity, excessive dust, or poor ventilation.

●Avoid locations in direct sunlight, with severe changes in humidity, or places where there are extremely high or low temperature

variations.

●Don't use the drive near radio or television receivers. It may interfere with their reception.

●Do not disassemble the drive. Dismantling the drive to attempt repairs or for other reasons is dangerous because the laser may

radiate outside the unit.

Cautions During Use

●Don't suddenly move the drive from a cold place to a warm place, or suddenly raise the room temperature. Condensation may

occur, causing abnormal operation.

●Make sure to remove the disc before moving the drive. The disc may be damaged, causing data loss.

●Be careful to prevent foreign objects such as liquids or metal from entering the drive. Should by chance a foreign object enter

the drive, please consult the dealer where the drive was purchased.

●Don't use benzene or thinner to clean dirt from the drive. Don't allow chemicals such as insecticides to contact the drive. Use a

soft cloth to wipe the drive, or moisten a cloth with neutral detergent diluted with water and use it to clean particularly dirty

areas.

●Don't cutoff the electric power while the drive is operating.

●When connecting two E-IDE devices to the Primary or Secondary connectors, make sure that the two devices are not both

configured as Master, or both as Slave. If they are both set the same, Windows may fail to run or recognize the drives.

●The total length of the E-IDE cable should be less than 18 inches (about 45 cm).

●Make sure the power to the host computer is turned OFF before connecting.

●Never insert a damaged disc into the drive.

●In wintertime, don't use a disc soon after bringing in from outdoors. Use it only after it has reached room temperature.

Cautions Concerning Disc Cleaning

●Remove the disc by pressing the eject button.

●Use compressed air to clear dust from the disc. (Spray the compressed air for about 5 seconds).

●Check to see if there is dirt on the surface of the disc. Be careful not to touch the disc with the fingers when doing this. (See Fig.

●After cleaning the disc with compressed air, place it on the disc tray and mount it.(See Fig. 2)

●We suggest using dry air cleaner as compressed air for cleaning.

Other Cautions

●When moving the equipment, make sure that the disc has been removed from the drive.

●When connecting connectors, make sure that the power is OFF. If the power is ON, there is a possibility of short circuit.

●When not using the drive for a long period, dust may adhere to the disc tray. Before using the drive again, use dry air cleaner to

remove the dust from the tray.

fig1

1. Check

2. Recording surface

fig2

1. 50 to 100mm

Back

●A new technology called Just Link, that overcomes buffer underrun problems

●JustSpeed (Optimum Write Speed Control) function

●Completely sealed door construction provides high reliability.

●An improved anti-heat design means that no cooling fan is needed.

●Easy-to-use tray model.

●Enhanced-IDE (ATAPI) model

●Compliant with industry standard Orange Book Part II (CD-R) and Part III (CD-RW).

●Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, photo CDs*1, and CD-Text

●Can read data at 40x speed (6.0MB/sec data transfer rate), write data at 24x speed (CD-R, 3.6MB/sec data

transfer rate.) and write data at 10x speed *2(High Speed CD-RW, 1.5MB/sec data transfer rate).

●The recorded CD-RW media can be played in a DVD player or a multi-read CD-ROM Player, maintaining

future compatibility.

●Supports random UDF for easy writing to CD-RW discs.

●UDMA Capable

*1 Bundled software does not support this writing format.

*2 The speed at which to write on the current standard CD-RW disks is 4x recording (at a data

transfer rate of 600KB/second).

Explains the system environment required for using the drive as a CD-R/CD-RW drive.

PC IBM PC/AT compatible

Operating System Windows ME/98/95(ORS2 or later)

Windows NT Workstation Ver.4.0 (Service Pack 4) or later

Windows 2000 (Professional) and XP

CPU Pentium 200 MHz or higher (when using Just Link)

Memory 64MB or more

Harddisk Hard disk with average access time of 19msec or less, and data transfer speed of 1,200KB/sec or greater.

1GB or more free space.

Interface Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave)

Drive bay 5.25-inch half height bay required

Power +5V/+12V power socket required

Recommended discs CD-R: Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs

CD-RW: Ricoh and Mitsubishi Chemical discs

High Speed CD-RW: Ricoh and Mitsubishi Chemical discs

Multi-read compatible (Random UDF compatible) drives are:

●Drives that can read low reflectivity discs.

●Drives that support Packet Writing.

Front Panel

Rear panel

Front Panel

1. Disc tray

This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject

button) and the disc will be mounted.

Caution

Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of

the drive.

2. Headphone jack

This jack is for connecting headphones or mini-speakers.

3. Volume control

This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for

the audio output connectors on the rear panel.

Caution

Turn the volume down before turning on the power. Sudden loud noises can damage your hearing.

4. Busy indicator

Indice

Manuali Unità CD/CDR popolari di altre marche

Philips

Philips CDD3610 Manuale utente

QPS

QPS Que!Fire Manuale utente

LG GCC-4241N Manuale utente

Plextor

Plextor 12X-3 Guida

Samsung

Samsung SN-324B Manuale utente

Teac

Teac CD-211E Manuale utente

SmartDisk

SmartDisk Firewire CD-R/W Manuale utente

Axis

Axis CD-ROM SERVER Manuale utente

LG CRD-8322B Manuale utente

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Istruzioni per l'installazione

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Manuale utente

Sony

Sony CRX230AE Manuale utente

Sony

Sony CRX - 160E Manuale utente

Panasonic

Panasonic KX-LD742 Manuale utente

Pioneer

Pioneer BDR-S13U-X Manuale utente

Panasonic

Panasonic LK-MC606BP Manuale utente

Panasonic

Panasonic CF-VCW Series Manuale utente

LG CRD-8320B Manuale utente