Ricoh MP9200A Manuale utente
NOTICE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communication. However, there is no
guarantee that interference will not occur in a particular
installlation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio / TV technician
for help.
Warning as to USE
This CD-R/RW & DVD-ROM drive together with software is a
product for utilizing CD-R/RW recording media with rewriting,
erasing and readout capabilities, as an external computer
memory device. Except in the case where copying of
CD-ROMs or the like is especially recognized under the
copyrights laws as being for the purpose of individual use by
the customer or the like, or in the case where the customer has
obtained permission to make copies from the rightholder,
reproduction of CD-ROMs and copyright laws. Take notice that
unauthorized copying may be subject to claims for damages
and to penalties.
CAUTION
Rating voltage for peripherals.
1. Headphone Jack
Rating Voltage output Audio Signal Max. 2V
FCC WARNING
Changes or modification not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Lower a volume
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The volume that exceeds 70dB occurs and the obstacle
sometimes breaks out.
Declaration of Conformity
"The Product complies with the requirements of the EMC
Directive 89/366/EEC and the Low Voltage Directive
73/23/EEC."
Please take notice that the manufacturer of this
equipment does not offer any warranty against data loss
due to inappropriate installation or handling, or direct or
indirect damages.
●
Please take notice that the manufacturer will bear no
responsibility for direct or indirect damages caused by
the use of this product or its malfunction.
●
Please take notice that the manufacturer will bear no
responsibility for damage to data caused by this product.
●
Please backup (copy) all important data as protection
against data loss.
●
PC DOS is a trademark of IBM Inc.● MS-DOS, Windows, Windows ® 95, Windows ® 98, Windows ® Me, Windows NT® and
Windows® 2000 are trademarks registered in the United States and other countries by the
Microsoft Corporation.
●
The company names and product names written in this manual are trademarks or registered
trademarks.
●
This manual uses the following symbols to indicate important information relating to the drive.
Failing to comply with the information in this manual and/or incorrect handling of the drive
may result in serious personal injury or damage to the product.
Indicates restriction or precaution that should be observed.
Provides useful additional information.
This manual contains important notes and product handling information. Be sure to read the
manual before using the product. For easy reference in the future, please keep the manual
at a handy location.
Multimedia Printer series
Thank you for purchasing the Multimedia Printer series drive MP9200A (hereafter referred to as the
drive). The drive enables you to play DVD-ROM or CD-ROM discs, write once and play CD-R discs, or
write, play, and rewrite CD-RW discs.
The following marks indicate media that can be used with the drive.
A new technology called Just Link incorporated
that overcomes buffer underrun problems
Buffer underrun errors that would occur when data transfer falls behind writing operation has been
inevitable for CD-R/RW drives. Just Link, which we at Ricoh developed on our own, is a new
technology that predicts possible occurrences of buffer underrun errors in advance and automatically
avoids them. The MP9200A is the industry's first-ever drive that features Just Link. With this
technology, the MP9200A ensures stable writing operation even under circumstances where buffer
underrun errors tend to occur with conventional drives.
New technology: (Optimum Write
Speed Control) function
When any write speed greater than 12X is specified, this function checks the media's capability to see
if it can be written at above-12X speeds. If the media is not capable of such speeds, the write speed is
reduced to 16X or 12X.
Caution
The JustSpeed (Optimum Write Speed Control) function is set to ON by default.
Depending on the ON/OFF setting of this function, the write speed is controlled as specified
below.
When the speed control is ON
Writing is performed at the speed of 16X in the lead-in area, at 16X from the 0-minute
position up to around the 5-minute position, and then accelerating up to 20X
approximately from the 5-minute position to the 15-minute position.
●
When the speed control is OFF
Writing is performed at the speed of 12X in the lead-in area, at 16X from the 0-minute
position up to around the 10-minute position, and 20X from around the 10-minute
position and after.
●
Obey the following cautions when handling the drive or discs.
Cautions During Installation
Install the drive in accordance with the specifications. Be careful to avoid locations
likely to cause vibration or shock.
●
Avoid locations where there is high humidity, excessive dust, or poor ventilation.●
Avoid locations in direct sunlight, with severe changes in humidity, or places where
there are extremely high or low temperature variations.
●
Don't use the drive near radio or television receivers. It may interfere with their
reception.
●
Do not disassemble the drive. Dismantling the drive to attempt repairs or for other
reasons is dangerous because the laser may radiate outside the unit.
●
Cautions During Use
Don't suddenly move the drive from a cold place to a warm place, or suddenly raise the
room temperature. Condensation may occur, causing abnormal operation.
●
Make sure to remove the disc before moving the drive. The disc may be damaged,
causing data loss.
●
Be careful to prevent foreign objects such as liquids or metal from entering the drive.
Should by chance a foreign object enter the drive, please consult the dealer where the
drive was purchased.
●
Don't use benzene or thinner to clean dirt from the drive. Don't allow chemicals such
as insecticides to contact the drive. Use a soft cloth to wipe the drive, or moisten a
cloth with neutral detergent diluted with water and use it to clean particularly dirty
areas.
●
Don't cutoff the electric power while the drive is operating.●
When connecting two E-IDE devices to the Primary or Secondary connectors, make
sure that the two devices are not both configured as Master, or both as Slave. If they
are both set the same, Windows may fail to run or recognize the drives.
●
The total length of the E-IDE cable should be less than 18 inches (about 45 cm).●
Make sure the power to the host computer is turned OFF before connecting.●
Never insert a damaged disc into the drive.●
In wintertime, don't use a disc soon after bringing in from outdoors. Use it only after it●
has reached room temperature.
Cautions Concerning Disc Cleaning
Remove the disc by pressing the eject button.●
Use compressed air to clear dust from the disc. (Spray the compressed air for about 5
seconds).
●
Check to see if there is dirt on the surface of the disc. Be careful not to touch the disc
with the fingers when doing this. (See Fig. 1)
●
After cleaning the disc with compressed air, place it on the disc tray and mount it.(See
Fig. 2)
●
We suggest using dry air cleaner as compressed air for cleaning.●
Other Cautions
When moving the equipment, make sure that the disc has been removed from the
drive.
●
When connecting connectors, make sure that the power is OFF. If the power is ON,
there is a possibility of short circuit.
●
When not using the drive for a long period, dust may adhere to the disc tray. Before
using the drive again, use dry air cleaner to remove the dust from the tray.
●
Do not use any commercially available cleaning kit, because such a kit may damage
the drive.
●
JustLink has made auto-avoidance against buffer underrun
errors possible.
●
JustSpeed offers optimum write speed control that matches
the CD-R media.
●
An improved anti-heat design means that no cooling fan is needed.● Easy-to-use tray model.● Enhanced-IDE (ATAPI) model● Compliant with industry standard Orange Book Part II (CD-R) and Part III (CD-RW).● Can read not only CD-R and CD-RW discs, but also video CDs, music CDs, photo
CDs*1, and CD-Text
●
Can read data at 40x speed (6.0MB/sec data transfer rate), write data at 20x speed
(CD-R, 3.0MB/sec data transfer rate.) and write data at 10x speed *2(High Speed
CD-RW, 1.5MB/sec data transfer rate).
●
The recorded CD-RW media can be played in a DVD player or a multi-read CD-ROM
Player, maintaining future compatibility.
●
Supports random UDF for easy writing to CD-RW discs.● UDMA-capable
*1 Bundled software does not support this writing format.
*2 The speed at which to write on the current standard CD-RW discs is 4x
recording (at a data transfer rate of 600KB/second).
●
Explains the system environment required for using the drive as a CD-R/CD-RW drive.
PC IBM PC/AT compatible
Operating System Windows Me/98/95(ORS2 or later)
Windows NT Workstation Ver.4.0 (Service Pack 5) or later
Windows 2000 (Professional)
CPU Pentium 166 MHz or higher (When using JustLink)
Memory 64MB or more
Hard disk Hard disk with average access time of 19msec or less, and data transfer speed of
1,200KB/sec or greater. 1GB or more free space.
Interface Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave)
Drive bay 5.25-inch half height bay required
Power +5V/+12V power socket required
Recommendation discs*2 Recommendation Tested to be compatible
CD-R Ricoh Taiyo Yuden, Mitsui Chemicals, Mitsubishi
Chemical, Maxell
CD-RW Ricoh Mitsubishi Chemical*1
High Speed CD-RW Ricoh Mitsubishi Chemical
*1 The disc written using the CD-R/RW drive may not be readable by CD-ROM drives.
Multi-read compatible (Random UDF compatible) drives are necessary.
*2 Even if it is the recommendation disc, some of discs may have possibility to fail
writing with highest writing speed with the problem on the disc. In this case, please
try to write with lower writing speed, or please try to use another disc.
Multi-read compatible (Random UDF compatible) drives are:
Drives that can read low reflectivity discs.● Drives that support Packet Write.●
Indice
Altri manuali Ricoh Unità DVD
