Riello GAS 4 P/M Guida rapida

Installation, use and maintenance instructions

2915246 (2) - 07/2016

Forced draught gas burner

Progressive two-stage or modulating operation

CODE MODEL TYPE

3753481 GAS 4 P/M 534 T80

Declaration of conformity in accordance with ISO / IEC 17050-1

Manufacturer: RIELLO S.p.A.

Address: Via Pilade Riello, 7

37045 Legnago (VR)

Product: Forced draught gas burner

Model: GAS 4 P/M

These products are in compliance with the following Technical Standards:

EN 676

EN 12100

and according to the European Directives:

MD 2006/42/EC Machine Directive

LVD 2014/35/UE Low Voltage Directive

EMC 2014/30/UE Electromagnetic Compatibility

The quality is guaranteed by a quality and management system certified in accordance with UNI EN ISO 9001.

Mr. U. Ferretti Mr. F. Comencini

2915246

TECHNICAL DATA

BURNER DESCRIPTION

BURNER EQUIPMENT

Thermal output 115 - 470 kW - 99.000 - 404.200 kcal/h

Operation • Two stages progressive

• Modulating (kit with controller available upon request)

Fuel Natural gas Pci 8 - 10 kWh/m

= 7000 - 8600 kcal/m

Minimum gas pressure For maximum output 9.8 mbar are needed measured at the coupling with

nil pressure in the combustion chamber and gas with calorific value of

8600 kcal/m

Maximum gas pressure 150 mbar

Electrical supply Three phase 220 V + 10% - 10% ~ 60 Hz without neutral

380 V + 10% - 10% ~ 60 Hz with neutral

Motor 1.5A / 220V - 2.4A / 380V

Ignition transformer Primary: 1.8A / 220V - Secondary: 1 x 8 kV - 30 mA

Absorbed electrical power 0.6 kW

Quantity Accessories

1 Flange

1 Gasket

8 Screws

1 Flange gasket

1Servomotor controlling air and gas

2Adjustment cam

3Power controller (for modulating to be

required separately)

4Control box re-set button

5Servomotor connection

6Fair leads

7Wiring terminal block

8Re-set push-button of the motor

overload relay

9Air pressure switch

10 Gas pressure test-point

Fig. 1

D2176

2915246

MAXIMUM DIMENSIONS

COMBUSTION CHAMBER PRESSURE - MAXIMUM OUTPUT

Min. output: 115 kW - 99.000 kcal/h.

*Length available with special blast tube to be separately required.

Burner

D2177

Boiler front-plate

drilling

160

165 M12

D1785

Kcal/h

mbar

D1786

2915246

MINIMUM GAS PRESSURE - OUTPUT

Pressure: detected at the pressure test-point 10) (fig. 1) with nil mbar into the combustion chamber.

Should the combustion chamber be pressurized, the pressure necessary will be that of the graph plus

the pressurization value.

Example: to obtain 350 kW it is necessary a gas pressure of 7 mbar and the combustion head set as indicated

at page 8.

If the combustion chamber is pressurized at 2 mbar, the pressure detected at the test-point 9) is: 7

+ 2 = 9 mbar.

If this value is too high, for very low gas pipework pressures, the gas gear 6) (page 8) could be more

open.

Do not decrease the pressure at the coupling under the values shown in the diagram.

Output: the maximum value is obtainable with gas Pci 8600 kcal/m

CORRELATION BETWEEN GAS PRESSURE AND BURNER OUTPUT

FIXING TO THE BOILER

Separate the blast tube from the burner body by

loosening the screws 7) and 3), fix the blast tube

to the boiler front plate 5) using the gasket 6)

provided.

Insert the burner on the holding bars 4) and

fasten the screws 7) and 3).

The combustion head adjustment should be

carried out as follows:

Loosen the screws 2) unhook the tension rod of

the air damper 1) remove the connecting lead of

the servomotor, withdraw the group A) from the

group B).

After the setting, re-assemble and verify that the

tension rod of the air damper was locked.

D2180

D2178

2915246

GAS SUPPLY

D2179

1- Gas pipe line 7- Safety valve

2- Cock valve 8- Adjustment valve

3- Filter 9- Adjusting throttle valve

4- Pressure stabilizer 10 - Burner

5- Pressure test-point 11 - Gas leak control device

6- Minimal gas pressure switch

Supplied

upon request to be carried out by the installer

2915246

BURNER ELECTRICAL WIRING

(carried out y the factory)

Key to layout

CMV Motor contactor

LFL... Control box

MB Burner terminal strip

MV Fan motor

PA Air pressure switch

RT Thermal cut-out

SM Servomotor

SO Ionisation probe

SP Plug-socket

TA Ignition transformer

TB Burner ground

20123876

2915246

ELECTRICAL CONNECTIONS TO THE WIRING TERMINAL BLOCK

(to be carried out by the installer)

NOTICE

- The electric wiring carried out by the installer must be in compliance with the rules in force in the Country.

- Leads minimal section 1 mm

- Adjustment for the motor thermal relay:

• at the beginning of the scale for 380 V;

• at the end of the scale for 220 V.

- Burners with non-stop operation.

For safety reasons, this type of burner must be stopped every 24 hours of operation, by means of an hours-

counter to be connected in series with the adjustment devices.

Key to layout

BP - Pressure probe

BT - Temperature probe

MB - Burner terminal strip

PC - Check pressure switch

PG - Min. gas pressure switch

RWF50 - Power controller

TR - High-low mode load remote control sys-

tem: controls operating stages 1 and 2

TL - Load limit remote control system: shuts

down the burner when the boiler temper-

ature or pressure reaches the preset

value.

TS - Safety load control system: operates

when TL is faulty

VR - Adjustment valve

VS - Safety valve

20124022

D2182

16 A

25 A

1.5 mm

2.5 mm

2915246

FIXING OF THE ELECTRICAL WIRES

All the electrical wires, which are to be connected to the terminal block 7) (fig. 1) shall pass through the fair leads 6) (fig.

1) as per this scheme.

1- Three phase supply: fair lead Pg 21

2- Single phase supply: fair lead Pg 13.5

3- Adjustment thermostat: fair lead Pg 13.5

4- Safety thermostat: fair lead Pg 13.5

5- Gas train:fair lead Pg 13.5, sheath ø 13

6- 2nd stage thermostat:fair lead Pg 13.5

(probe for modulating version)

7- Pre-sheared hole: fair lead Pg 13.5 (for power controller - modulating version)

8- Pre-sheared holeg

Further prospective signals or controls can be connected to the burner wiring terminal board by removing the metal weld-

nuts from the pre-sheared holes and inserting a commun fair lead for the passage and the clamping of the leads.

NOTES

- Do not exchange the neutral wire with the phase (avoid the plug-pin connection).

- Carry out a safe earth connection.

- Check the stop of the burner, by opening the boiler thermostat and the burner lock-out, by disconnecting the lead from

the flame probe.

WARNING

When closing the burner on its slide-bars, pull towards the outside the high voltage cable and the cable of the flame de-

tection probe, till to little tension.

D2184

2915246

BURNER START-UP CYCLE

Air-purge: loosen the screw placed on the minimal gas pressure switch mounted on the gas train

AIR PRESSURE SWITCH

The air pressure switch setting shall be carried out after having set all other

adjustments of the burner and the air pressure switch shall be at its lowest

set-point.

When the burner is operating, increase the adjustment pressure by turning

- slowly - clockwise the knob till reaching the burner lock-out.

Thereafter, turn the knob anticlockwise for 1 mbar and repeat the burner

start-up for checking the regularity: if lock-out intervenes turn the knob an-

ticlockwise for 0.5 mbar.

CAUTION:

do not turn the ionization probe, maintain the drawing position; should it be close to the ignition electrode, damage

may occur to the control box amplifier.

Screw

Plug for pressure measure

Pressure switch

S7506

1 ÷ 10

mbar

Adjustment knob

S7507

D2185

Probe position Ignition electrode position

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Riello Bruciatore

Riello

Riello RG2 Guida rapida

Riello

Riello RL 25 BLU TC Guida rapida

Riello

Riello Gulliver BG7D Guida rapida

Riello

Riello DB3 SM C01 TC FS1 A0 T250 Guida rapida

Riello

Riello RBS 200 2S Manuale utente

Riello

Riello RLS 280/E Guida rapida

Riello

Riello RLS 1600/EV C11 Guida rapida

Riello

Riello RS 34 MZ Guida rapida

Riello

Riello RS 68/EV ULX Guida rapida

Riello

Riello 3433823 Guida rapida

Riello

Riello 40 Series Guida rapida

Riello

Riello G10 Guida rapida

Riello

Riello G10D Guida rapida

Riello

Riello Gulliver RG0.3 Guida rapida

Riello

Riello 911T1 Guida rapida

Riello

Riello RLS 1300/E C11 Manuale di istruzioni

Riello

Riello RLS 70/M Guida rapida

Riello

Riello 40 F10 A Istruzioni per l'installazione

Riello

Riello PRESS 450 T/N Guida rapida

Riello

Riello RS 34/E MZ Guida rapida

Riello

Riello CAMRAY5 65/90B Guida rapida

Riello

Riello Gulliver BS1/M Guida rapida

Riello

Riello RX 70 S/PV Guida rapida

Riello

Riello RG2D Guida rapida

Manuali Bruciatore popolari di altre marche

True Induction

True Induction TI4B Manuale utente

Weishaupt

Weishaupt WG20 Series Manuale utente

Carolina Cooker

Carolina Cooker M116672 Manuale utente

Unigas

Unigas HTP2000 Manuale utente

baltur

baltur BT 250 DSG 4T Manuale utente

muenkel design

muenkel design round burner Manuale utente

Ecoflam

Ecoflam Multicalor 170.1 Manuale utente

baltur

baltur BT 14 DSGW Manuale utente

artisan

artisan Art-SB1 Guida

AESYS

AESYS TurboFire II Manuale utente

IKEA

IKEA GRILLSKÄR Manuale utente

RUSTA

RUSTA SAREK Manuale utente

PROPOINT

PROPOINT 8933657 Manuale utente

baltur

baltur TBL 1000 ME Manuale di riferimento

Riello Burners

Riello Burners P 200 P/G Guida rapida

WLD-TEC

WLD-TEC powerjet Manuale utente

MSR

MSR DRAGONFLY Manuale utente

baltur

baltur COMIST 23SP Manuale utente