Riello P200 T/N Guida rapida
Installation, use and maintenance instructions
2915832 (4) - 08/2012
Heavy oil burners
CODE MODEL TYPE
3437785 P200 T/N 467 T80
3437786 P200 T/N 467 T80
5832
1
TECHNICAL DATA
ELECTRICAL DATA
Motor IE1
Motor IE2
Thermal power - Output 515 / 2280 kW - 45 / 200 kg/h (See sheet 3)
Operation 1st stage - 2nd stage - 3rd stage
Fuel Oil with max. viscosity 50mm2/s (7°E) at 50°C
with kit: max. viscosity 500mm2/s (65°E) at 50°C
Pump 350 kg/h at 25 bar
Electrical supply 3N ~ 220/380V
60 Hz
Fan motor rpm
V
kW
A
3470
220/380
5,5
19,7 - 11,4
Ignition transformer V1 - V2
I1 - I2
230 V - 2 x 6 kV
2 A - 35 mA
Electrical power consumption kW max 20
Electrical supply 3N ~ 220/380V
60 Hz
Fan motor rpm
V
kW
A
3568
220/380
5,5
20 - 11,5
Ignition transformer V1 - V2
I1 - I2
230 V - 2 x 6 kV
2 A - 35 mA
Electrical power consumption kW max 20
5832
2
1 - Suction line
2 - Return line
3 - Air shutter opening motor
4 - Pump pressure adjustment screw
5 - Manometer plug (G 1/8)
6 - Vacuometer plug (G 1/2)
7 - Reset push-button of the motor overload relay
8 - Electric board
9 - Cable clamps
10 - Control box reset push-button and lock-out
lamp
11 - Adjustment thermostat
12 - Regulating bush for combustion head
13 - Wiring terminal board
14 - Ignition transformer
15 - Filter
16 - Valves group
17 - Manometer
18 - Lamp
19 - Commutator
20 - Low limit thermostat
21 - High limit thermostat
22 - Timer
Fig. 1
Quantity Accessories
2 Flexibles tubes
2 Nipples
4 Screws
1 Gasket for flange
5 Cable clamps
*It is possible with a spacer, upon request
DIMENSIONS
5832
3
COMBUSTION CHAMBER PRESSURE - MAXIMUM OUTPUT
(Three nozzles in operation)
Operation field: Limit Safety
When the burner operates with only one or two nozzles, the pressurization conditions are improved and no
problems arise.
Boiler front plate drilling
Combustion head projection
For the combustion head projection carefully follow the boiler
manufacturer indications.
A proper protection with refractory material on the combustion head
projecting into the combustion chamber shall be made, when boilers
with frontal smoke box are used.
5832
4
OPERATION AND EFFICIENCY OF THE BURNER
ACCESSOIRES
RADIO DISTURBANCE PROTECTION KIT: Code 3010386
If the burner is installed in places particularly subject to radio disturbance (emission of signals exceeding 10 V/m) owing
to the presence of an INVERTER, or in applications where the length of the thermostat connections exceeds 20 metres,
a protection kit is available as an interface between the control box and the burner.
1st STAGE
POWER AND OUTPUT
MINIMUM MAXIMUM
kW kg/h kW kg/h
1st nozzle: ignition phase 376 33 763 67
1st+ 2nd nozzle: intermediate phase 763 67 1516 133
1st + 2nd + 3rd nozzle: operation phase 1140 100 2279 200
2nd STAGE
POWER AND OUTPUT
MINIMUM MAXIMUM
kW kg/h kW kg/h
1st nozzle: ignition phase 376 33 763 67
1st + 2nd nozzle: 1st stage of operation 763 67 1516 133
1st + 2nd + 3rd nozzle: 2nd stage of operation 1140 100 2279 200
3rd STAGE
POWER AND OUTPUT
MINIMUM MAXIMUM
kW kg/h kW kg/h
1st nozzle: 1st stage of operation 513 45 763 67
1st + 2nd nozzle: 2nd stage of operation 1026 90 1516 133
1st + 2nd + 3rd nozzle: 3rd stage of operation 1140 100 2279 200
5832
5
HEAVY OIL SUPPLY LINE
RING SUPPLY LINE
(for heavy oil with viscosity up to 50°E at 50°C)
1- Tank (heated for heavy oil)
2- Filter (with resistance for oil > 7°E at 50°C)
3- Forwarding pump
4- Control manometer
5- Shutter valves (in couple) excluding the burner
6- Burner (provided for Kit for heavy oil code no. 3000721)
7- Pressure adjuster
8- Filter (with resistance for oil > 7°E at 50°C)
9- Burner pump
WARNING
- The oil could easily flow through the pipes if those are properly seized, protected and heated (by electricity, steam
or hot water).
- The forwarding pump capacity should be at the least double of that of the burner pump.
- If several burners are supplied through the same ring supply line, the forwarding pump should have a capacity of
approx. 30% more than the sum of the single burners outputs.
- For starting-up: after excluding the burner by the shutter valves (5) let the oil flow into the supply ring up to reach
the required circulation; after than open the valves and supply normally the burner.
GRAVITY SUPPLY LINE
(only for oil with max. viscosity up to 7°E at 50°C)
Notice: before placing the burner in operation, ensure that the return line is open. Any obstruction may damage the
pump seal.
H
meters
L meters
ø 1” ø 11/4”
0210
0,5 3 11
1412
1,5 5 13
2614
Pump priming
Loose the tap of the vacuometer plug
(6) (fig. 1) and wait for the oil flow.
H = Difference in the pipes height
L = Total length of the suction tube
5832
6
INTERNAL WIRING DIAGRAM
(carried out by the factory)
LEGEND
CMV Fan motor contact maker TB Burner earth
CO Commutator TE Electronic thermostat
CR Resistor contact maker TM Maximal thermostat
FR Photoresistance Tm Minimal thermostat
MB Burner terminal strip TP Timer
MV Fan motor L1 Lamps for 1st stage
RMO Control box L2 Lamps for 2nd stage
RT Overload L3 Lamps for 3rd stage
SPre-heater tank V1 Oil valves for 1st stage
SM Air-damper actuator V2 Oil valves for 2nd stage
SO Probe PT100 V3 Oil valves for 3rd stage
TA Ignition transformer VS Safety valves
D2618
5832
7
WIRING CONNECTORS TO THE TERMINAL BOARD
(carried out by the installer)
2645
220V 380V
A Ampere T35 T25
B Ampere T50 T35
C mm24,0 2,5
D mm210 6
HRemote lock-out signal
I1 Optional switch on-off burner
MB Burner terminal strip
PS Reset push - button
SA High temperature oil alarm
TL Limit control device system
TS Safety control device system
T2 Load control system for 2nd stage
T3 Load control system for 3rd stage
NOTE:
yCheck the lock-out by darkening the photo-cell after removal of the cover.
ATTENTION HIGH VOLTAGE.
yIn case of supply 220V without neutral, connect the motor and the pre-heater thank through delta (the “star”
connection is the original one, made for 380V).
yNOTE
In systems where the run of wiring connecting the thermostat exceeds 20 metres in length, or in places where
the burner is subject to particularly disturbing electromagnetic interference (over 10 v/m), you must insert the
relay-interface kit item number 3010386.
5832
8
CHOICE: OF THE NOZZLES - OF THE PUMP PRESSURE -
OF THE COMBUSTION HEAD ADJUSTMENT
• First of all state the maximum output required with all three nozzles in operation.
• On the base of the maximum output choose, from table A, three related nozzles.
Nozzles: 60° - Pump pressure: 25 bar.
• The references of table B should be followed in case of need of:
- modification of the pump pressure in order to vary the output,
- diverse composition of the 3 nozzles group,
- knowledge of the output in 1st and 2nd stage.
SUGGESTED NOZZLES
The pump pressure is referred to all three nozzles operating. The pump pressure increases automatically when two
nozzles are operating and becomes higher with only one nozzle.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Riello Bruciatore
Riello
Riello 20010541 Guida rapida
Riello
Riello RS 70/EV Guida rapida
Riello
Riello 521T80 Guida rapida
Riello
Riello RLS 68/E MX Guida rapida
Riello
Riello RX 300 S/PV Guida rapida
Riello
Riello RLS 70 Guida rapida
Riello
Riello PRESS GV INCINERATOR Guida rapida
Riello
Riello RLS 1000/M MX Guida rapida
Riello
Riello RS 28/M Guida rapida
Riello
Riello G2 Guida rapida
Riello
Riello GAS 7/2 Guida rapida
Riello
Riello 40 Series Guida rapida
Riello
Riello RS 25/E BLU Series Guida rapida
Riello
Riello RL 28/M Guida rapida
Riello
Riello G5RK Guida rapida
Riello
Riello 3726312 Guida rapida
Riello
Riello BG6.1D Guida rapida
Riello
Riello F15 Guida rapida
Riello
Riello BGK1 Guida rapida
Riello
Riello GAS 5 P/M Guida rapida
