RIGTEC CWC01 Manuale utente
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
SWIVEL COUPLERS
(CWC01)
USER GUIDE
Version 1.0
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
Thank you for purchasing a Rigtec Swivel Couplers.
We hope you enjoy using the Swivel Couplers as much as
we’ve enjoyed designing and manufacturing them.
If you have any questions, suggestions or just want to say hello;
please contact the team at [email protected]
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
CONTENTS
SAFETY INFORMATION 3
SWIVEL COUPLER PARTS 5
SWIVEL COUPLER SAFETY INFORMATION 6
AIR FRAME X10 APPROVED RIGGING LOCATIONS 7
AIR FRAME X20 APPROVED RIGGING LOCATIONS 8
AIR FRAME X25 APPROVED RIGGING LOCATIONS 9
AIR FRAME X30 APPROVED RIGGING LOCATIONS 10
AIR FRAME X40 APPROVED RIGGING LOCATIONS 11
AIR FRAME X50 APPROVED RIGGING LOCATIONS 12
ATTACHING TO AIR FRAME:
LANDSCAPE 13
PORTRAIT 14
FLOOR PROJECTION 15
SAFETY STEEL CABLES 16
SPECIFICATION 17
CE DECLARATION OF CONFORMITY 18
UKCA DECLARATION OF CONFORMITY 19
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
3
SAFETY INFORMATION
These instructions should be handed over to the
person carrying out the installation.
• Only a qualied, trained and competent technician should carry out
installation work.
• The device should only be used with approved accessories and spares.
• Do not exceed the Working Load Limit (WWL) – when used with other
accessories make sure that the Working Load Limit of any component is
not exceeded.
• Care should be taken when lifting and moving – the combined weight of
the device and any accessory should be within safe manual handling limits.
• Care should be taken when transporting that injury is not caused - make
sure the device and any attached accessory is correctly secured.
• All equipment should be visually inspected before use and in the event of
any damage, it must be immediately taken out of service and assessed by a
competent person.
• Any suspended accessory must be independently secured with an
approved safety wire/s. Local laws or regulations should be consulted
regarding the additional safety of hanging equipment
• When working at elevated heights or under a suspended load, make sure
that all necessary precautions have been taken.
• Only install the approved projectors into the Air Frame, as listed in the User
Guide. Attempting to install projectors other than those listed in the User
Guide may result in serious injury.
• Do not use the Air Frame outdoors. The Air Frame should not be installed
where it can be exposed to wind or rain.
• Do not expose the Air Frame to moisture or excessive heat.
• Do not install the Air Frame on unstable surfaces.
• Do not hang the Air Frame from unstable, unsafe or inappropriate objects/
structures. Ensure the structure can support the overall weight.
• When stacking Air Frames, ENSURE all four locking pins are securely
positioned through the adjoining male and female Air Frame stacking
connectors.
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
4
SAFETY INFORMATION
These instructions should be handed over to the
person carrying out the installation.
• Do not install an Air Frame whilst people are under the hanging area.
• Do not make adjustments to a hanging Air Frame or Atom Grip whilst
people are under the hanging area.
• A Minimum of TWO people should be used to lift, carry and install the Air
Frame with a projector installed.
• Thorough examination of lifting equipment must take place at least every
12 months by a qualied technician.
In addition to these scheduled examinations, equipment will require a thorough
examination following:
• Any accident or dangerous occurrence.
• Any signicant change in conditions of use.
• Any long periods of inaction.
• Each time the equipment is used.
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
5
PART NAMES
Use this page as a reference of the various part names throughout
this User Guide.
1. Quick Trigger Clamps
2. Quick Trigger Clamp Handle
3. 32mm Clamp
4. 32mm Clamp Thumb Screw
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
6
SWIVEL COUPLER
SAFETY INFORMATION
Before attaching the Swivel Couplers to the Air Frame please read the
following safety information:
1. Swivel Couplers MUST ONLY be attached to the Air Frame in
the APPROVED LOCATIONS (See pages 7-12 for details on the
approved locations)
2. DO NOT attach Swivel Couplers to any other part of the frame
other than those highlighted in Images 1, 2 and 3.
3. The approved locations should only be used for the correct
orientation. Please be aware, not all approved locations can be
used in all orientations – DO NOT use the oor projection
approved locations for landscape projection.
4. Please note, Swivel Couplers MUST NOT be attached to the
front removable bar.
5. Always use FOUR Swivel Couplers to suspend the Air Frame.
6. Any suspended accessory must be independently secured with
an approved SAFETY WIRE/S. Local laws or regulations should
be consulted regarding the additional safety of hanging
equipment.
7. Only stack a MAXIMUM of THREE Air Frames (AF02-X10), when
suspending with Swivel Couplers.
8. If you wish to use Rigtec Swivel Couplers with a third party
frame, please consult the third party frame user guide or
contact the manufacturer for important safety information
such as the approved hanging locations.
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
7
AIR FRAME X10
APPROVED RIGGING
LOCATIONS
These diagrams show the approved locations where the Swivel
Couplers can be mounted to the Air Frame X10.
Swivel Couplers MUST ONLY be attached to the Air Frame in the
APPROVED LOCATIONS
DO NOT attach Swivel Couplers to any other part of the frame other
than those highlighted in Images 1, 2 and 3.
The approved locations should only be used for the correct
orientation. Please be aware, not all approved locations can be used
in all orientations – DO NOT use the oor projection approved
locations for landscape projection.
Please note, Swivel Couplers MUST NOT be attached to the front
removable bar.
1. Landscape Projection
2. Portrait Projection 3. Floor Projection
Back
Top Bottom
Right
Left
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
8
AIR FRAME X20
APPROVED RIGGING
LOCATIONS
These diagrams show the approved locations where the Swivel
Couplers can be mounted to the Air Frame X20.
Swivel Couplers MUST ONLY be attached to the Air Frame in the
APPROVED LOCATIONS
DO NOT attach Swivel Couplers to any other part of the frame other
than those highlighted in Images 1, 2 and 3.
The approved locations should only be used for the correct
orientation. Please be aware, not all approved locations can be used
in all orientations – DO NOT use the oor projection approved
locations for landscape projection.
Please note, Swivel Couplers MUST NOT be attached to the front
removable bar.
1. Landscape Projection
2. Portrait Projection 3. Floor Projection
Back
Top Bottom
Right
Left
T I +44 (0)1926 290 418 E I hello@rigtec.com W I www.rigtec.com
9
AIR FRAME X25
APPROVED RIGGING
LOCATIONS
These diagrams show the approved locations where the Swivel
Couplers can be mounted to the Air Frame X25.
Swivel Couplers MUST ONLY be attached to the Air Frame in the
APPROVED LOCATIONS
DO NOT attach Swivel Couplers to any other part of the frame other
than those highlighted in Images 1, 2 and 3.
The approved locations should only be used for the correct
orientation. Please be aware, not all approved locations can be used
in all orientations – DO NOT use the oor projection approved
locations for landscape projection.
Please note, Swivel Couplers MUST NOT be attached to the front
removable bar.
1. Landscape Projection
2. Portrait Projection 3. Floor Projection
Back
Top Bottom
Right
Left
Indice
Altri manuali RIGTEC Rack e supporto
