Rikon Power Tools 10-110B Manuale utente
10” Cabinet Saw Sliding Table
Model: 10-110B/E
Owner’s Manual
For more information:
www.rikontools.com or [email protected]
For Parts or Questions:
Record the serial number and date of purchase
in your manual for future reference.
Serial number:
Date of purchase:
Part #10-110B/EM2
IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following in-
structions must be followed at all times.
There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or
used for any other application other than that for which it was designed. If you have any questions about its application, do not
use the tool until you have contacted us and we have advised you.
KNOW YOUR POWER TOOL. Read the owner’s manual carefully. Learn the tool’s applications, work capabilities, and its
specific potential hazards.
ALWAYS KEEP VISITORS AWAY FROM RUNNING MACHINES.
All visitors should be kept a safe distance from the work area.
ALWAYS MAKE THE WORKSHOP CHILDPROOF.
Childproof with padlocks, master switches, or by removing starter keys.
NEVER OPERATE A TOOL WHILE UNDER THE INFLUENCE OF DRUGS, MEDICATION, OR ALCOHOL.
ALWAYS WEAR PROPER APPAREL.
Never wear loose clothing or jewelry that might get caught in moving parts. Rubber-soled footwear is
recommended for the best footing.
ALWAYS USE SAFETY GLASSES AND WEAR HEARING PROTECTION.
Also use a face or dust mask if the cutting operation is dusty.
NEVER OVERREACH.
Keep your proper footing and balance at all times.
ALWAYS GROUND ALL TOOLS.
If your tool is equipped with a three-pronged plug, you must plug it into a three-hole electric receptacle.
If you use an adapter to accommodate a two-pronged receptacle, you must attach the adapter plug to a
known ground. Never remove the third prong of the plug.
ALWAYS AVOID DANGEROUS ENVIRONMENTS.
Never use power tools in damp or wet locations. Keep your work area well lighted and clear of clutter.
ALWAYS REMOVE THE ADJUSTING KEYS AND WRENCHES FROM TOOLS AFTER USE.
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before
turning it on.
ALWAYS KEEP YOUR WORK AREA CLEAN. Cluttered areas and benches invite accidents.
NEVER STAND ON TOOLS.
Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted.
2
Operator Safety: Required Reading
General Safety Warnings
ALWAYS CHECK FOR DAMAGED PARTS.
Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure
that it will operate properly and perform its intended function. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard
or other damaged parts should immediately be properly repaired or replaced.
ALWAYS DISCONNECT TOOLS.
Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters.
ALWAYS AVOID ACCIDENTAL STARTING.
Make sure switch is in “OFF” position before plugging in cord.
NEVER LEAVE TOOLS RUNNING UNATTENDED.
1. Always wear eye protection.
2. Keep hands away from the saw blade while machine is running.
3. Always use blade guard during normal cutting operations.
4. Always use splitter during normal cutting operations.
5. Use push sticks when ripping narrow stock.
6. Always use fence while ripping and miter gauge while cross-cutting.
7. Never reach over or behind saw blade while machine is running.
8. Do not remove cut-off or jammed pieces until blade has come to a full stop.
9. Disconnect machine from power source before making repairs or adjustments.
10. Do not expose saw or power cord to water or use in damp locations.
SAVE THESE INSTRUCTIONS.
Refer to them often.
3
Table Saw Safety Rules
Safety Warnings........................................................................................................................................2 -3
Table Saw Safety Rules ..........................................................................................................................3
Specifications ........................................................................................................................................4
Contents of Package ............................................................................................................................5
Unpacking and Checking Contents ...................................................................................................5-6
Getting To Know Your Sliding Table ............................................................................................................7
Assembly ..............................................................................................................................................8-12
Adjustment...................................................................................................................................12-13
Operation.......................................................................................................................13-14
Rip Fence Installation................................................................................................................................. ..... 15
Maintenance .......................................................................................................................................... ..... 15
Troubleshooting........................................................................................................................................16
Parts Diagram...........................................................................................................................17
Parts List................................................................................................................18
Warranty ...................................................................................................................................19
Table of Contents
4
12”
49”
51-12” x 9-7/8”
49-1/4”
0-45o Forward/Back
18-1/4” x 23-3/4”
Minimum Table Travel
Maximum Table Travel
Sliding Table Dimension
Miter Fence Length
Miter Fence Angles
Sliding Carriage Size
Specifications
5
Model 10-110B/E 10” Table Saw Sliding Table is shipped complete in 2 boxes.
Unpacking and Checking Contents
Separate all “loose parts” from packaging materials and check each item with “Table of Loose Parts” to
make sure all items are accounted for, before discarding any packaging material.
Box #1
Content of Package
A
B
C
TABLE OF LOOSE PARTS
Item Part Name Qty
A Sliding Table 1
B Miter Fence 1
C Loose Parts Bag 1
6
TABLE OF LOOSE PARTS
Item Part Name Qty
A Swing Arm Assembly 1
B Swing Arm Extension Bar 1
C Sliding Table Carriage 1
D Sliding Table Support Arm 1
E Loose Parts Bag 1
Box #2
A
B
C
D
E
7
Getting To Know Your Sliding Table
1. Flip Stop
2. Miter Fence
3. Sliding Table
4. Sliding Table Locking Pin
5. Push Block
6. Slide Handle
7. Swing Arm Assembly
8. Carriage Table Support Arm
9. Sliding Table Carriage
23
145
6
7
8
9
8
Mounting the Swing Arm Bracket
1. Open the motor cover located at the left side of
the saw.
2. With assistance hold the swing arm bracket
against the saw body and attach using four 8MM
hex bolts, four 8MM washers and four 8MM hex
nuts.
3. Slide the four 8MM hex bolts through the bracket
and saw body and attach using the four 8 washers
and four 8MM hex nuts from inside the saw body.
Figure 1.
Installing the Swing Arm Extension Bar
1. Slide the swing arm extenstion bar through the
swing arm bracket making sure that the large hole
is installed first and that the set screw is pointing
downward. Figure 2.
Mounting the Sliding Table
1. Locate the sliding table mounting hardware
which includes two knobs, two T-nuts, two 8MM
washers and two adjusting plates. Figure 3.
2. Assemble the hardware as shown (Fig. 3) and
slide the T-nut into the track (Fig. 4) making sure
that the clamp plate is against the bottom of the
table assembly.
Figure 1
Figure 2
Figure 3
Figure 4
Assembly
9
Mounting the Sliding Table Continued
3. Slide the hardware toward the cast mounting
bracket located on the saw body. Place the
adjusting plate on top of the set screws as shown
(A,Fig.5).
4. Tighten the lock knob slightly, leaving loose for
adjustment.
5. Repeat procedure for rear mounting bracket.
6. Adjusting the parallel of the saw table and sliding
table with the four set screws (A, Fig.5).
Installing the Sliding Table Carriage
1. Locate the sliding table carriage mounting
hardware as shown. Figure 6.
2. Slide the T-nuts bar into the side channel of the
sliding table. Figure 7.
3. Attach the carriage table support arm to the
bottom the the sliding table carriage using two 8MM
carriage bolts, two 8MM washers and two 8MM hex
bolts. The head of the carriage bolts should lock
into the bottom of the sliding table carriage. Finger
tighten the two 6MM hex bolts only until next step
is completed. Figure 8.
Figure 5
Figure 6
Figure 7
Figure 8
Assembly
A
Carriage Table Support Arm Installation
1. Insert the support arm into the swing arm
extension bar as shown (A, Fig. 9) making sure
that bearing assembly rests between the adjusting
nuts and the swing arm extension bar (B, Fig. 9).
Reminder: Tighten the carriage bolts shown in
Figure 8 on page nine once the support arm is
installed.
2. Hold the support arm in place by installing the
second bearing set and adjusting nuts as shown.
The second set of bearings should be installed
against the bottom side of swing arm extension
bar. Figure 10.
NOTE: Do not overtighten the adjusting nuts as
the bearings will bind and the table will not slide
smoothly.
3. Hold the sliding table carriage against the
sliding table and install the lock knobs through
the carriage to the T-nuts bar in the sliding table
channel. Figure 11.
4. Line up the two holes in the side of the support
arm with the two holes in the side of the sliding
table carriage (Fig. 12).
5. Insert the two locking knobs with the long
threaded ends as well as two 6MM washers
through the support arm and through the sliding
table carriage (Fig. 12). Attach with with two 6MM
washers and two 6MM hex nuts.
10
Figure 9
Figure 10
Figure 11
Figure 12
Assembly
A
B
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Rikon Power Tools Sega
Rikon Power Tools
Rikon Power Tools 10-347 Manuale utente
Rikon Power Tools
Rikon Power Tools 11-200 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-370 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-306 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-300 Manuale utente
Rikon Power Tools
Rikon Power Tools 15-400 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-3061 Manuale utente
Rikon Power Tools
Rikon Power Tools 18" Professional Bandsaw Manuale utente
Rikon Power Tools
Rikon Power Tools 10-326 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-341 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-324TG Manuale utente
Rikon Power Tools
Rikon Power Tools 10-350 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-351 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-308 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-320 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-342EVS Manuale utente
Rikon Power Tools
Rikon Power Tools 10-325 Manuale utente
Rikon Power Tools
Rikon Power Tools 10-600VS Manuale utente
Rikon Power Tools
Rikon Power Tools 10-325 Manuale utente
Rikon Power Tools
Rikon Power Tools 14-700 Manuale utente
