Rime Lite i4 TTL Manuale utente
Operating Instructions
i4 TTL
.
Thank you for choosing a Rimelite product.
Please refer to the camera’s instruction manual together with this operating instruction.
Rimelite’s i Flash TTL is compatible with Canon/Nikon DSLR and mirrorless cameras that are equipped with a hot shoe. The i. Flash TTL is an all-powerful strobe lighting
system with compact design DC battery pack and AC power supply pack. It supports E-TTL II, Nikon i-TTL with great performance.
Rimelite’s accumulated TTL technology supports the idealized exposure value in anywhere, under any environment.
Built-in innovated Rimelite’s TS-4 Wireless system.
The most Optimized User Interface , visible color LCD display and compact design, it supports ‘ very easy operation’ and ‘most logical TTL performance’.
TTL and HSS mode should only be used with TS-4 Wireless controller and trigger.
To synchronize TS-4 wireless trigger and i.flash , press on the i. Flash TTL, press ‘Mode’ button once on TS-4 wireless controller & trigger
Nomenclature
1.Flash tube 2. Bracket 3. Battery 4. Battery release button 5. Shoulder Strap 6. Sync sensor
7. LCD display 8. Flash status indicator 9. Control button 10. Power On/Off button
11. Control button 12. Battery status LCD display 13. Battery status indicator buttonbutton
Power On/Off
Press and hold power switch to turn on/off the unit.
Power On
Auto Power Off function
- To reduce battery power use, i Flash TTL is designed to go into Sleep mode after 30 minutes of non-activity and to turn off automatically after 40 minutes of non-activity.
Hot Shoe
Control flash with TS-4 wireless controller & trigger
Attach TS-4 to Hot-shoe, turn on your camera and TS-4.
*Settings should be controlled through TS-4.
Camera Settings
Press and hold the simultaneously for 3 seconds to select Canon/Nikon camera.
Make sure the camera to be synced with is selected before use.
The unit does not operate when selection is paired with a different camera.
<TTL> Mode
Set camera scene modes to <Av> (aperture priority), <Tv> (shutter priority or <M> (manual) mode to work with i Flash TTL.
<M>Mode
Set the selection mode <TTL>,<M> to M on TS-4, and adjust the accurate power on TS-4.
Channel Setting
i4 TTL flash is equipped with a built-in TS-4 Wireless system. Press until the numeral digit starts blinking.
Then, press the buttons to set the channels from 1~80.
*Set TS-4 wireless trigger channel to the same designated channel on the i4 TTL flash for operation. After pressing CH on the
wireless trigger, push the buttons to change channel
Channel settings
Change channel
buttons
Group Setting
Designate up to 4 i Flash TTL to one GROUP and 4 of these flashes can control at the same time.
Press to assign up to 4 flashes: to a group.
*TS-4 wireless trigger group should be set to the same designated group in i4 TTL flash in order to operate the flash. Press
the A, B, C and D buttons on wireless trigger for settings.
TTL Settings
Group settings
e.g) When controlling 4 flashes in 1, 2 groups
Flash no.1 Ch 01, GR A
Flash no. 2 Ch 01, GR B
Flash no.3 Ch 02, GR A
Flash no. 4 Ch 02, GR B
e.g) When controlling 4 flashes
Flash no.1 Ch 01, GR A
Flash no. 2 Ch 01, GR B
Flash no.3 Ch 01, GR C
Flash no. 4 Ch 01, GR D
e.g) When controlling 3flashes
Flash no.1 Ch 01, GR A
Flash no. 2 Ch 01, GRB
Flash no.3 Ch 01, GRC
e.g) When controlling 2flashes
Flash no.1 Ch 01, GR A
Flash no. 2 Ch 01, GRB
TTL Settings
<TTL> mode <M> mode
Press button on the TS-4 transmitter to switch between <TTL> mode and <M> mode..
In TTL mode, when the shutter on the camera of which the TS-4 is mounted to is pressed exposure is automatically controlled.
TS-4 wireless trigger must be used in order to operate the TTL mode.
*All operations must be done on the transmitter of the TS-4 controller.
Settings will not be applied when operating on the unit itself.
8 F-STOP in TTL mode, 7 F-STOP in manual mode.
i-Flash TTL from 1/1 full power to the lowest output of 1/128 with an increment of 0.1 F-Stops and a total of 70 levels
in manual mode.
…when decreasing output power:
…when increasing output power:
TTL / M settings
Flash exposure compensation
TTL MODE
When shooting under <TTL> auto flash mode under various environments, it may demand a minor adjusting
exposure value. After checking your photograph for under and overexposure, press the + - buttons on the TS-
4 to adjust exposure compensation with an increment of 0.1 F-Stops.
*All operations must be done on the transmitter of the TS-4 controller. Settings will not be applied
when operating on the unit itself.
In the case of an underexposed photograph, press TS-4’s button
to increase exposure compensation up to a maximum of +3.0, 30 steps.
In the case of an overexposed photograph, press TS-4’s button
to decrease energy level down to a maximum of -3.0, 30 steps.
Manual Mode
Flash output is adjustable from 1/128 to 1/1 full power with an increment of 0.1 F-Stops.
*All operations must be done on the transmitter of the TS-4 controller. Settings will not be applied when
operating on the unit itself.
After doing exposure compensation in <TTL> mode, switch to the <M> manual flash mode to keep
photographing under the determined flash output.
After setting up the M mode by pressing the button on TS-4,
manipulate the buttons to adjust flash output from 1/1 full power to the lowest output of 1/128
with an increment of 0.1 F-Stops and a total of 70 steps.
HSS Flash Mode
TTL MODE HSS Flash MODE
M MODE HSS Flash MODE
The HSS flash mode syncs flashes at camera shutter speed of 1/200 ~ 1/8,000 seconds.
Press on TS-4 transmitter to turn on the TTL HSS mode (when using Canon)
is displayed on both the LCD displays of TS-4 and i Flash TTL.
*For Nikon cameras, i Flash TTL enters HSS flash mode automatically according to the
shutter speed adjustment of camera.
Shutter speed settings
Sync mode settings
Bulb. 30~1/180 secs
ordinary sync mode
1/200~1/8,000 secs
HSS mode
Indice
