Rinnai Arriva Scheda tecnica
Arriva Operation and
Installation Manual
Appliance must be installed with an approved Rinnai ue system.
Appliance must be installed, commissioned and serviced by a licensed tradesperson
in accordance with these instructions and all applicable local rules and
regulations.
Owner, please retain this manual for future reference.
®
SUPPORTING
ASTHMA CARE
SENSITIVE
CHOICE
Approved by the Asthma and
Respiratory Foundation
LIMITED WARRANTY
Please keep these instructions in a safe place for future reference.
RECORD AND ATTACH YOUR PROOF OF PURCHASE BELOW:
Your Retailer:__________________________________________________
Name:________________________________________________________
Address:______________________________________________________
_____________________________________________________________
Telephone:( _______ ) __________________________________________
Date of Purchase: ______ / ______ / _________
TERMS AND CONDITIONS
1. During the 24 month period from date of
purchase and subject to clauses 2 and
3 below, Rinnai New Zealand Limited
(“Rinnai”) will, at its own discretion, either
replace or repair any defective product at
no charge to the customer.
2. This warranty covers manufacturing defects
only. This warranty will not apply if (for
example) the product has been improperly
installed or is otherwise installed contrary
to manufacturer’s recommendations, has
been damaged during or after installation,
has not been operated in accordance
with operating instructions, or has been
subjected to damage or abuse beyond that
expected from conditions of normal use.
3. Warranty claims may be invalid if not
accompanied by details of the installing or
supervising gas tter’s registration number
and the gas tting certication number.
4. This warranty commences from the date of
purchase. Proof of purchase is required at
the time of any warranty claim.
5. Servicing of the product is to be carried out
by a Rinnai authorised service centre.
All Rinnai appliances meet or exceed the
safety standards required by New Zealand
gas and electrical regulations. The company
is constantly improving its products and as
such specications are subject to change or
variation without notice.
Rinnai brings you peace of mind
with a 2 year minimum warranty.
Contents
WARNING
Improper installation, adjustment, alteration, service or maintenance
can cause property damage, personal injury or loss of life.
For assistance or additional information contact Rinnai on 0800
RINNAI (0800 746 624).
Customer Information
Limited Warranty 2
About Your Arriva 4
Safety 5
Clearances 6
Mantles and Surrounds 7
General Information 8
Basic Heater Operation 10
Operation Using Remote Control 12
Care and Maintenance 15
Servicing 17
Abnormal Flame Pattern 18
Troubleshooting 19
Arriva Accessories 22
Installer Information
General and Specication 24
Appliance Positioning 25
Gas Supply and Direct Flue Wall Penetrations 26
Flueing 27
Arriva Installation 32
Installing the Log Set 35
Commissioning 37
Setting Air Guide Vanes 38
Front Fascia and Top Panel 39
Wiring Diagrams 40
Commissioning Checklist 42
Installer Details 43
Customer Contacts 44
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
4
About Your Arriva
Gas Consumption: 31.5 MJ/h (high)
Output: 7.0 - 1.8 kW
Efciency: 80% (high)
Heats Area Up To: 70 - 95 m2 (depending on the region you live in)
Auto overheat discharge vent
Double glazed
frame window
Room air return
Log set
Louvre, warm air discharge
Receiver window
for infra red remote
control receiver (5 m
range) and blockage
indicator for lter/
louvre blockages
Control panel
7
10
From left to right:
- error display
- timer indicator
- operation indicator
- on/off button
Power ued appliance that uses a fan to draw air from the outside for combustion. Combusted
gases are propelled back outside creating combustion efciency and better room air quality.
The operation section of this manual has been written to:
• Highlight the safe operation and positioning of this appliance
• Advise on maintenance, servicing and troubleshooting to ensure optimum
performance
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
5
Safety
Do not restrict
warm air
discharge by
placing articles
in front of the
appliance.
This appliance
must not be
used for any
purpose other
than heating.
Young children
should be
supervised
at all times.
Hand or body
contact with
the appliance
must be
avoided.
Do not spray
aerosols while
the appliance is
operating. Most
contain butane
gas which can
be a re hazard
if used near the
appliance.
Do not allow
anyone to sit,
lean or sleep
directly in front
of the appliance.
Do not allow
anyone to
post articles
through into
the heater.
Do not place
articles on the
top panel or
obstruct the
auto overheat
discharge
vent.
Do not unplug
the appliance
while it is
operating.
Do not use
power boards
or double
adaptors to
operate this
appliance.
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
6
Clearances
The appliance must not be installed where curtains or other combustible materials could come
into contact with the heater. In some cases curtains may need restraining.
The diagram below shows clearances required when the heater is operating.
100 mm
1000 mm
100 mm
250 mm
This appliance discharges a large volume of warm air at a low level.
Heat emanating from this re may over time affect the appearance of some
materials used for ooring, such as, carpet, vinyl, cork or timber. This may be
amplied if the air contains cooking vapours or cigarette smoke. To avoid this
occurring, it is recommended that a mat be placed in front of the appliance.
Floor
protection
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
7
Mantles and Surrounds
Mantles and surrounds can be added to complement design providing they are within the
clearance requirements below.
Mantles 75 mm is the minimum clearance above (to allow the overheat safety device
to open), with a maximum depth of 25 mm.
For every 25 mm of added depth, there must be 25 mm of vertical clearance.
Refer mantle diagram below.
Surrounds 75 mm is also the minimum clearance from the sides for access to side
louvres, opening, cleaning and room air return. At 75 mm, the maximum
depth is 25 mm. For additional depth, 25 mm of horizontal clearance is
required for every 25 mm of added depth.
Refer surround diagram below.
Angled for free ow clearance for room air return
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
8
General Information
Before operation
Read these instructions to get an overview of how to operate, maintain and service your
Rinnai Arriva.
Hearths
A hearth is not necessary but can be used for decorative purposes or protection of sensitive
ooring if required. Some general guidelines when installing a hearth.
• It must not obscure the front of the re
• The bottom of the appliance must be level with the top of the hearth so there is a
continuous level
• Size should be at least the width and depth of the re
Remember to adjust the dimensions of the cavity to allow for the hearth.
Electrical connection
The standard electrical connection is to the right hand side of the heater
front assembly. If necessary this can be changed by your electrician to
terminate on the left.
A 3 pin plug is supplied which must be connected to a dedicated earthed
power point. The power point must be 300 mm to the side of the re
and a maximum of 1500 mm (cord supplied is 1500 mm). It must not
be above the unit as this is a potential re hazard.
Alternatively the appliance can be direct wired if the power supply is to be concealed. The
electric isolation switch must be accessible after the appliance has been installed.
If the supply cord is damaged and requires replacing, it must be replaced by a licensed
tradesperson. This must be a genuine replacement part available from Rinnai.
Installation by a licensed tradesperson
Ensure your installer talks to you about the use and care of this appliance and that you
understand these instructions. They also need to complete their installer details on page 43 of
the installation manual and leave the manual with you.
Improper installation, adjustment, service or maintenance can cause serious injury, property
damage or death. Please ensure your installation is completed by a licensed tradesperson.
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
9
General Information
Remote control
• Avoid leaving the remote in direct sunlight and do not place it close to the warm air
discharge louvres of the heater
• Avoid dropping or getting wet
• Some uorescent lights may interfere with the transmission of the remote control signals,
changing position from which you are operating the remote may help
The remote uses 2 x 1.5V AAA batteries. Never mix old and new batteries.
Remove batteries if not going to be used for a long time. This will help avoid
damage from leaking batteries.
Positioning of the Arriva
To gain maximum heating advantage from the bottom air discharge,
position the Arriva close to the oor.
Can be fully recessed as long as a 75 mm clearance above and to the
sides is maintained for; operating devices to function, access to the unit,
cleaning and servicing.
Safety devices
Your Arriva is designed with the following safety devices.
• ame failure sensing system
• explosion relief
• overheat safety switch
• air temperature sensor
• thermal fuse
• overcurrent fuse
• spark detector
TV installation above replace
If installing a at screen television above the re, the main issue is heat. Heat from
the re itself and heating from the ueing components that may sit behind the
television, especially if recessed.
The Arriva has a fan that distributes warm air at a low level, this pushes the heat out and
around the room as opposed to straight up. The Arriva also has a power ue that has virtually
zero clearance to any cavity in which it is installed. The ueing components are also small and
generate very little heat.
The general rule for installations above a replace is the bottom of the television recess should
be at least 450 mm above the re. It is still however up to you to check with your television
supplier to verify clearances. Some TV manufacturers have warranty conditions that state a
television is not to be installed above a replace.
Rinnai New Zealand Limited Arriva Operation and Installation Manual: 10343-E
05-10
10
Basic Heater Operation
This appliance has a sealed combustion chamber that requires purging
before gas can ow and the unit can start. As a result the combustion fan
starts several seconds before there are any signs of the Arriva starting.
The normal ignition sequence is:
1. When the On/Off button is pressed the LED will glow red and the
combustion fan starts to purge the system.
2. Pilot sparker will operate and as soon as a spark is sensed gas will ow
to the pilot.
3. When the pilot ame is established gas will ow to the front and then
rear burners.
4. When all burners are on the heater will automatically modulate between
burner settings to achieve and maintain the default set temperature of
22 °C.
General notes
about ignition
The heater can be operated and stopped without the remote control by
using the On/Off button on the top panel of the heater. This operation is
called the automatic mode. In automatic mode the default set temperature
is 22 °C.
If the heater is turned off using the On/Off button on the heater control
panel, when it is turned back on it will lose all timer and clock settings until
the remote is used to re-transmit the information. The remote control
stores the clock, timer and temperature settings of the heater.
Operation
without the
remote control
(automatic
mode)
For the remote control functions to be available, the appliance On/Off
button must be in the On position.
The remote control emits an Infra Red signal and must be aimed at the
receiver unit located on the right side of the unit. The normal operating
range is 5 m. This range may vary depending on the position of the
installation and strength of the batteries.
The remote control transmits information to the heater whenever a button
is pressed except when the:
• remote display is deactivated
• lock function is activated
When the timers are being set, information is transmitted only when the
‘Time Set’ button is pressed.
Signal transmissions are conrmed by a brief illumination of the
transmission signal indicator on the remote. The unit will also ash and
beep to conrm the settings have been received.
When the remote is not used for a period of approximately 5 seconds,
the display will default to standby mode, displaying only the time. To re-
activate press any button on the key pad.
Operation with
the remote
control
STANDBY
ON
Flame
Auto
Off
Lock
Timer 2
Timer 1
Override
Time
Set
Temperature
Lock
Clock
AM
PM
Timer 1
Set
Set ON OFF
ON OFFTimer 2 Set
OverrideAuto Off
Time
Flame
Altri manuali per Arriva
1
Indice
Altri manuali Rinnai Camino da interno
Rinnai
Rinnai RF1800 Manuale utente
Rinnai
Rinnai Symmetry RDV3611 Manuale utente
Rinnai
Rinnai Symmetry RDV3611 Specifiche tecniche
Rinnai
Rinnai SLIMFIRE 25 Manuale utente
Rinnai
Rinnai RHFE1000 Manuale utente
Rinnai
Rinnai Novo Cube Manuale utente
Rinnai
Rinnai Arriva 752 Manuale utente
Rinnai
Rinnai Symmetry RDV3611 Manuale utente
Rinnai
Rinnai LS1000 Manuale utente
Rinnai
Rinnai Neo RIB2311N Manuale utente
Rinnai
Rinnai Royale FS35 ETR Manuale utente
Rinnai
Rinnai Neo Series Manuale utente
Rinnai
Rinnai Symmetry RDV3611 Manuale utente
Rinnai
Rinnai RIBF2N Manuale utente
Rinnai
Rinnai Neo Series Manuale utente
Rinnai
Rinnai Symmetry RDV3600 Manuale utente
Rinnai
Rinnai Ember Series Manuale utente
Rinnai
Rinnai Linear Series Manuale utente
Rinnai
Rinnai RHFE752ETRN Manuale utente
Rinnai
Rinnai ES750 Manuale
