11. Troubleshooting
9. Operation check
<Disclaimer> The manufacturer shall not be held responsible for below
1. Misinterpretation of the installation instructions, poor connection, random disassembly and inappropriate installation.
2. Damage caused by inappropriate transportation.
3. Accidents or damages caused by fire, pollution, abnormal voltage, and natural disasters(Earthquake, lightning, wind, floods etc.)
4. Loss of business profits, business interruptions, business information losses and other financial losses
caused by malfunction or use of the sensor.
5. Total compensation beyond the selling price in all cases.
Problem LED Status Possible Causes Troubleshooting Measures
Door will not open even if a
person comes close to it. Off
Green
For no reason, the door
opens and closes
(ghosting)
A rain cover (sold separately) protects the sensor from snow and rain when installed outside.
Blue
Insert the sensor
connector correctly until it
clicks.
Supply the correct voltage
to the sensor.
(12~24V AC/DC)
Remove the moving object
from the detection area.
Reduce the radar sensitivity
volume to an appropriate value
according to the manual.
Activate the snow mode
setting
Set the presence timer
setting to 30 or 60 seconds.
Remove the highly reflective object
from the detection area or lower the
IR sensitivity volume.
Voltage failure
Defective wiring
There is a moving object
in the detection area
The radar sensitivity volume has
been set too high relative to the
installation environment.
Dust, frost, water droplets
are on the lens
Defective wiring
Excessive reflections in the infrared
detection area
Red
There is a moving object in the radar
detection area.
Remove the moving objects.
Radar
sensitivity volume
IR sensitivity
volume
12. Rain cover (not provided)
13. Spot finder (not provided)
A spot finder can be used to accurately locate the position of the infrared detection area and is a useful tool during the commissioning of this sensor.
MODEL : WC-IR/BL
Green + Red Infrared reflectivity is too low Adjust the mounting height or IR
sensitivity. If necessary, deactivate
low reflection setting(Menu:141)
An automatic doors
keeps open.
Set the frequency setting of both
sensors to be different (Menu: 041)
Detection area overlaps
with that of another sensor
Sensitivity value is too low Increase the radar sensitivity volume
to an appropriate value.
Loose connector
Recheck wiring
Green color after the red or blue Clean the sensor lens
Fallen leaves
Snowfall
Infinity presence timer setting used
Recheck wiring
45°
(o)(o) (x)
IR Sensor
0°~ 25° 0°~ 25°
SF100
Detection point of IR
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
yellow
blue
Gray
Brown
Supplying DC 12 to 24V ,
make current flow from Gray to Brown.
It is under test state
when there is not
current flow.
sensor Gray
Brown
sensor
Gray
Brown
sensor
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
Green
White
When it is used in automatic door controller in compatible with European standard EN16005,
the safety output signal timing can be checked based on the timing diagram below.
Safety Relay Output
/ Test Input Setting
Activation Relay Output
N.O.
N.C.
de
t
c
e
te
dn
Udet
c
et
eDde
tce
t
ed
nU
de
t
c
e
teD
d
etcetednUdetceteDd
e
tce
t
ednU
Power off
f
f
o
r
ewoP
f
fo
rew
oP
Menu
Menu
Menu
Menu
Menu
Menu
Menu Menu
N.O.
N.C.
Non-test Test Non-test
Test response DETECTION as
response to TEST
Test input used
Test input not used
DC12~24V
2 1
10. Timing of safety output signal
3 2 1
3 2 1 3 2 1 1 2
31
2 3
1
2
3
3 2 1 3 2 1
3 2 1 3 2 1 3 2 1
3 2 1
After completing installation, walk into the detection area of the sensor. If you feel that the detection
area is incorrect, then adjust it as per section 8. The infrared spot finder SF100 is recommended to
accurately set the infrared detection area.The IR sensitivity volume can also be increased/
decreased if detection problems persist.
If the device detects when there is nothing in the infrared detection area,
turn the sensitivity volume counter-clockwise.
Radar Radar Radar Radar Radar Radar
