RoamAlert AR3KY01-030 Manuale utente

Access Keypad

Installation Guide

Access Keypad

Installation Guide

Access Keypad Installation Guide

Warranty

Stanley Healthcare Solutions' products are warranted against defects in materials and

workmanship and shall perform in accordance with published specifications for 1 year.

Stanley Healthcare Solutions' warranty is limited solely to the repair or replacement of

the defective part or product. Stanley Healthcare Solutions reserves the right to change

product specifications without notice.

Regulatory Statements

United States - Federal Communication Commission (FCC)

This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-

ing two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause unde-

sired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class

A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

Warning: Any changes or modifications not expressly approved by Stanley Healthcare

Solutions could void the user's authority to operate the equipment.

Canada - Industry Canada

The term "IC:" before the certification/registration number only signifies that Industry

Canada technical specifications were met.

Important Recommendation

Stanley Healthcare Solutions’ systems are designed to assist staff in providing a high

degree of safety for people and assets and therefore should be used as a component of a

comprehensive security program of policies, procedures, and processes. As with every

security system, Stanley Healthcare Solutions highly recommends regular system opera-

tional checks to verify functional integrity.

Access Keypad Installation Guide

Introduction

Included in this Package

Access Keypad Overview

The access keypad is used by facility staff to temporarily bypass a protected exit, allowing

a tag to enter the exciter field without generating an alarm. The keypad also produces

audible and visual indication of alarm and bypass conditions and visual indication of

power on.

When the door controller is placed in test mode (Position 0, SW102), the keypad can be

used to help tune the exciter field. See “Door Controller and Exciter Installation Proce-

dure” in Chapter 4 of either the Halo Installation Manual (981-000026-000) or

the RoamAlert Installation Manual (981-000043-000) for details.

Two installation modes are available (set by JP3 on the back of the keypad):

• Mode 1 (formerly known as PINpad mode).

Up to 1000 unique PIN (Personal Identification Number) codes can be stored in the

door controller and managed at the RoamAlert server PC. In this mode, the Access

Keypad software tracks each code in the Activity Log. Use this mode when the facility

requires a record of which staff member bypassed the exit at a specific date and time.

• Mode 2 (formerly DKY Keypad mode).

This mode uses four generic passcodes, 2 for bypass and 2 for reset. Mode 2 is much

easier for the facility to administer, but it does not provide the detailed tracking and

added security of Mode 1. In Mode 2, only the date and time of each bypass is

recorded in the Activity Log.

QTY PART # Description

1 AR3KY01-030 Access Keypad

1N/A Keypad Cable

1N/A Modular Splitter (for two keypad installations)

1N/A Low voltage retrofit bracket

2N/A Mounting screws

1 981-000018-000 This document

Access Keypad Installation Guide

Specifications

Installation Tips

• Select the appropriate mode for this installation.

Identify whether the facility requires unique PIN codes or not.

• Select the appropriate volume level for audible alarm indication.

Is the keypad located in an area that must be kept quiet? The keypad has 5 volume

levels plus inaudible (off). Select the level according to facility requirements.

• Decide whether the keypad should initiate bypass prior to or after tag

detection.

Mount the keypad outside the exciter field to allow bypass before tag detection.

• Use the Y adapter for dual keypad installations.

If the exit requires two keypads (one on each side of the door), use the supplied Y

splitter to connect both keypads to the jack on the front of the controller.

Installation Procedure

Follow these steps to install the keypad:

1 Place the jumper on the upper 2 pins of JP3 on the keypad back to select

Mode 1 (unique PIN codes) or place the jumper on the lower two pins to

select Mode 2 (generic codes). If this is to be a Mode 2 keypad, continue

with “Mode 2 Passcode Programming Procedure” on page 5 after

completing keypad installation. See Figure 1 on page 7.

2 Set the appropriate volume level on J1 on the keypad back. Place the jumper

on the top pair of pins to set the volume to inaudible (off). Each lower pair

of pins increases the volume, with the bottom pair being the loudest. See

Figure 1 on page 7.

3 Mount a standard single-gang electrical box (not supplied), or the supplied

low-voltage retrofit bracket, at a convenient height (usually wall switch

height) in the selected location (usually just outside the exciter field). Careful

Input Rating 12 VDC @ 200 mA

Operating/Storage Temp 32° F to 120° F (0° C to 49° C)

Relative Humidity 0-85% RH @ 70° F (21° C) non-condensing

Dimensions 4.5” L x 2.75” W x 2.5” H (11.5 x 7.0 x 6.5 cm)

Mounting B11R Carlon Retrofit box (supplied)

Access Keypad Installation Guide

placement (not crooked) of all exposed components is the hallmark of a

professional installation.

4 Run the supplied keypad cable from the KEYPAD jack on the controller

front panel into the electrical box and connect to the keypad jack.

5 Mount the keypad into the electrical box or into the retrofit bracket with the

supplied screws.

Mode 2 Passcode Programming Procedure

When the keypad is in Mode 2, five memory slots on the keypad are available for pro-

gramming. Slots 1 and 3 are used for Bypass codes. Slots 2 and 4 are used for Reset codes.

A fifth slot is used for the Master Pass Code. The default codes assigned to the keypad

memory slots are:

• Bypass: 1938

• Reset: 1939

•Master: 987654

When you program the codes, you may use one code for both bypass slots and one code

for both Reset slots, but you cannot use the same code for Bypass and Reset. Usually, you

program separate codes and provide them to separate user groups.

To c h a n g e t he d e f a u l t Bypass or Reset codes, follow these steps:

1 Make sure the keypad has power.

2 Enter the Master Pass Code.

3 Press #.

4 Enter the slot number (1 or 3 for Bypass, 2 or 4 for Reset).

5 Press #.

6 Enter a new passcode (3 to 6 digits).

7 Press #.

8 Note the new passcode(s) and store in a safe place.

To c h a n g e t he d e f a u l t Master Pass Code, follow these steps:

1 Make sure the keypad has power.

2 Enter the Master Pass Code.

3 Press #.

4 Enter the Master Pass Code again.

Access Keypad Installation Guide

5 Press #.

6 Enter a new passcode (3 to 6 digits).

7 Press #.

8 Note the new Master Pass Code and store in a safe place.

To restore a factory default code, follow these steps:

1 Make sure the keypad has power.

2 Enter the Master Pass Code.

3 Press #.

4 Enter the slot number (1 or 3 for Bypass, 2 or 4 for Reset).

5 Press #.

6 Do NOT enter a passcode.

7 Press #again.

8 The default passcode is restored.

Master Reset

To reset the keypad to its factory default passcodes, follow these steps:

1 Apply power to the keypad.

2 Short the contacts on the J7 solder points at the upper right of the keypad

back. (See Figure 1 on page 7.) The keypad will beep.

3 Press the * key three times. The keypad will beep to indicate that the defaults

are loaded.

Access Keypad Installation Guide

Access Keypad Notes and Diagrams

Figure 1: Keypad Jumper Locations

Connecting a Third-Party Keypad to a Controller

Third-party keypads can be connected to a Halo or RoamAlert R3 controller using a

6P6C modular plug according to the following pin-outs at the controller keypad jack,

from left (pin 1) to right (pin 6):

Pin Description

1+12V DC

2Ground

3BYPASS_IN

4RESET_IN

5ALARM_OUT

6BYPASS_OUT

J1 – Speaker Volume

Top Pair = OFF

Bottom Pair = Loudest

JP3 – Mode

Top Two = Mode 1

Bottom Two = Mode 2

J7 – Master Reset

Stanley Security Solutions

Senior Technologies Division

1550 N. 20th Circle

Lincoln, NE 68503

Telephone: USA: 800-824-2996

Canada: 866-559-6275

Int’l: +1 (613) 592-6997

Web site: www.stanleyhealthcare.com

August 2009. 981-000018-000 Rev 03.

Indice

Altri manuali RoamAlert Tastiera

RoamAlert

RoamAlert ECO Manuale utente

Manuali Tastiera popolari di altre marche

BFT

BFT SELETTO Manuale utente

Micro Id

Micro Id MP7G3BL Manuale di istruzioni

WindowMaster

WindowMaster WLI 130 Manuale utente

ACT

ACT ACT PRO 1030 Manuale utente

Cardin

Cardin SSB Series Manuale utente

Harman Kardon

Harman Kardon KP 1 Manuale utente

Chamberlain

Chamberlain KPR2000 Guida utente

CYP

CYP CR-KP1 Manuale utente

Aeware

Aeware k-35 Series Guida di riferimento

Aritech

Aritech CS-175 Series Manuale utente

GE NetworX NX-1600E Series Manuale utente

Lenze AC Tech

Lenze AC Tech MC SERIES Manuale utente

Burg Wächter

Burg Wächter secuENTRY 7711 Manuale utente

Aeware

Aeware in.k450 Manuale utente

Lenze

Lenze EPM-H410 Manuale utente

Toshiba

Toshiba RKP007Z Manuale utente

Gemini

Gemini GEM-DXK1 KEYPAD Manuale utente

Russound

Russound MDK-C5 Manuale operativo