Robe Tarrnatula Manuale utente
Version 1.1
2
3
CAUTION!
Disconnect the Robin Tarrantula from mains before installing the beam shaper kit!
Instructions stated on the following pages describe remodelling the Robin Tarrantula to the Robin Tarrantula
with the beam shaper.
The Tarrantula Beam Shaper Kit includes:
1 x Beam shaper 2 x Head cover
1 x Connecting cable 1 x Tilt Stop
2 x Self-tapping screw 3x8 3 x Allen head bolt M4x35 with washers
2 x Cable holder 1 x Blank cap
2 x Self-tapping screw 2.2 x 6.5 2 x Self-tapping at head screw 3x8
1 x PCB RB3135
4
1. Remove both head covers (1), the rear cover (2) and the arm cover (3) (arm without tilt lock).
3 2
1
2. Unscrew the screw (4) which secures the zoom module (5) in the head.
3. Slide the zoom module (5) up to remove it from the head.
4
2. Unscrew the screw (4) which secures the zoom module (5) in the head.
3. Slide the zoom module (5) up to remove it from the head.
5
5
6
4. Remove PCB covers (6) and (7) by unscrewing 10 fastening screws (screws in red circles on the picture
below)..
7
5. Pass the connecting cable (8) through the pivot (9).
6. Screw the new head cover (11) with the aperture (10) for connector on the head.
9
810 11
6
7. Pass the connecting cable (8) with the connector (13) through the aperture in the new cover and screw it by
means of two self-tapping screws 3x8 (14). .
8
14
13
8. Arrange the shape of the connecting cable (8) as shown on the picture below, check especially bending of
the cable (15) that it will not restrict movement of the zoom module. Fasten the connecting cable to the white
conductors by means of the cable binder (16) as shown on the picture below.
16
8
15
7
9. Connect the connecting cable to connectors (17) in PCB. Fasten the connecting cable to bundled conductors
by means of two cable binders (18).
18
17
10. Unscrew the connector (13) from the head cover (11) and pull it out of the head cover. Remove the head
cover (11) from head and screw the PCB covers (6) and (7) by means of 10 fastening screws to the head.
11
13
6
7
8
11. Connect the Tarrantula to mains and wait for its reset. Take care of free connecting cable during the
Tarrantula reset.
12. Use the display menu Manual Eect Control to set the head to the horizontal position. Dimmer and Shutter
have to be closed (0 DMX).
13. Set the Zoom at 255 DMX, put and hold the zoom module horizontally on the head and slowly change
the zoom value at 0 DMX (the zoom module is pulling to the head).
5
Zoom=255
Zoom=0
14. Check the zoom movement.
15. Disconnect the Tarrantula from mains
16. Secure the zoom module to the head by screwing the screw (4).
4
9
17. Pass again the connecting cable (8) with the connector (13) through the aperture in the head cover (11)
and screw it by means of two self-tapping screws 3x8. Secure the connecting cable (8) to the cover by means
of the two cable holders (26) with self-tapping screws 2.2 x 6.5 (27) Screw the cover (11) on the head (check
the connecting cable does not obstruct in movement of the zoom module). Screw the second part of
the head cover and the rear cover of the head (2). .
1113
18. Unscrew the left Allen head bolt (19) fastening the original tilt stop (20) and screw the new tilt stop (21) on
the original tilt stop by means of the new Allen head bolt M4x35 (22). The washer (28) has to be inserted
to the hole in the original tilt stop (20). Do not tighten this bolt.
19. Unscrew the rest of original Allen head bolts, insert washers (28) to holes (29) and place the new tilt stop to the
position shown on the pictures below and screw it by means of the two Allen head bolts M4x35 (22). Fully
tighten all three Allen head bolts.
19 21 22
20
2
26 27
10
Important: the washers (28) has to be inserted in all holes (29) of the original tilt stop (20).
22
28
20 29
20. Place and screw the arm cover (23) on the arm.
23
21. Screw the blank cap (25) to the free opening (24) in the head cover by means of two self-tapping at head
screws 3x8 (26).
24
26
25
Altri manuali Robe Attrezzatura di illuminazione
Robe
Robe ANOLIS Manuale utente
Robe
Robe Anolis Calumma S MC Manuale utente
Robe
Robe Color Wash 700E AT Manuale utente
Robe
Robe Color Spot250AT Manuale utente
Robe
Robe Anolis Ambiane XP56 Manuale utente
Robe
Robe ROBIN 300X Manuale utente
Robe
Robe Robin BMFL FollowSpot Manuale utente
Robe
Robe ColorSpot 700E AT Manuale utente
Robe
Robe ColorWash 250 AT Manuale utente
Robe
Robe Scan 575 XT Manuale utente
Robe
Robe ClubWash 600 CT Manuale utente
Robe
Robe DigitalSpot 5000 DT Manuale utente
Robe
Robe Flare CB Series Manuale utente
Robe
Robe ANOLiS ArcSource Submersible II Manuale utente
Robe
Robe ROBIN iPointe65 Manuale utente
Robe
Robe Euphoria CB series Manuale utente
Robe
Robe Robin MiniMe Manuale utente
Robe
Robe Robin 600 Purewhite WIreless DMX Manuale utente
Robe
Robe Robin Actor 3 Smart White Manuale utente
Robe
Robe Robin CycBar UV Manuale utente
