Robertshaw RS9110 Manuale utente
RS9110
Operation Manual
Table of Contents Page
Table of Contents 1
Thermostat Operation 2-3
Thermostat Quick Reference 4-7
Programming 8-10
Technician Setup Menu 11-15
Terminal Designations 16
Equipment damage hazard.
Do not operate the cooling
system if the outdoor
temperature is below 50°F
(10°C) to prevent possible
compressor damage.
Caution
RS9110
1
THERMOSTAT OPERATION
1
2
3
4
5
LCD Screen Temperature Setpoint Buttons
User ButtonsFan Switch
System Switch
Mon
Room
Set At
SLEEP
Menu
FAN
+1
SYSTEM
ON AUTO COOL OFF HEAT
PM
2
1
2
3
4
5
THERMOSTAT OPERATION
Caution:
LCD Screen
See page 4 for details about
thisdisplay readout.
Fan Switch
Select ON or AUTO. ON will run the
fan continuously. AUTO will cycle
the fan on only when the heating or
cooling system is running.
System Switch
Select the operationmode on
your HVAC system. Selecting
HEAT turns on the heat mode.
Selecting COOL turns on the air
conditioning mode.
Selecting OFF turns both heating
and cooling o.
Temperature Setpoint Buttons
Press the + or - buttons to selectthe
desired room temperature.
User Buttons
Use these buttons to set up
yourprogramming options. Refer to
the next page for detail.
When the battery icon appears replace your AAA batteries
immediately. Failure to do so may result in your heating and cooling
system becoming inoperable. Freezing or over heating can occur.
3
Days of the week
and time.
Button Options
Programmable Time Periods:
This thermostat has 4
programmable time periods per
day.
Indicates the current
room temperature.
Displays the user
selected setpoint
temperature.
Hold: Is displayed
when thermostat
program is
permanently
overridden.
Low Battery
Indicator:
Replace batteries
when indicator is
shown.
System Operation
Indicators:
The , or icon
will display when the
COOL, HEAT, or
(fan) is on.
NOTE: The compressor
delay feature is activeif
these icons are ashing.
The compressor will not
turn on until the 5 minute
delay has elapsed.
Tech Set
Next Step Min Com On
Com Delay H eat
Cool Swing
Room
Sun Mon Tue Wed Thu
Hold Filter
Set At
SatFri
Set Time
Run Sched
Set Sched
Hold
Prev Step
Menu
Done WAKE LEAVE RETURN SLEEP
+1 +2
AM
PM
THERMOSTAT QUICK REFERENCE
4
The low battery indicator is displayed when the 2x AAA batteries
need to be replaced.
Important:
Battery Door Information
Replace with
2xAAAAlkaline
Batteries. High
quality Alkaline
batteries are
recommended.
Use the finger bevel on
the lower portion of the
thermostat to open the
easyaccess battery door.
THERMOSTAT QUICK REFERENCE
5
Temporary and Permanent Hold Feature (if using programming)
Temporary Hold: The thermostat will display HOLD and RUNSCHED on the
left of your screen when you press the or key. If you do nothing, the
temperature will remainat this setpoint until next time period. Your program
setpoint will then replace your temporary setpoint.
Permanent Hold: If you press the HOLD key at the left of your screen, you will
see HOLD appear below the setpoint temperature in the display. The thermostat
will now permanently stay at this setpoint and can be adjusted using the or
keys.
To return to program: Press the RUN SCHED key at the left of your
screentoexit either temporary or permanent hold.
THERMOSTAT QUICK REFERENCE
6
Filter Change Reminder
If your HVAC contractor has congured the thermostat to remindyou when the
air lter needs to be changed, you will see FILTER in the display when your air
lter needs to be changed.
Resetting the filter change reminder: When FILTER reminderis displayed, you
should change your air lter and reset thereminder by holding down the second
button from the top left side of the thermostat for 3 seconds.
Mon
Room
Set At
SLEEP
Menu
FAN
+1
PM
SYSTEM
ON AUTO COOL OFF HEAT
Hold down 3 seconds to
reset lter reminder.
THERMOSTAT QUICK REFERENCE
7
Set Time
1. Press the MENU button.
2. Press SET TIME.
3. Day of the week will be ashing. Use the or key to
select the current day of the week.
4. Press NEXT STEP.
5. The current hour is ashing. Use the or key to select
the current hour. When using 12-hour time, make sure the correct
a.m. or p.m. choice is selected.
6. Press NEXT STEP.
7. Minutes are now ashing. Use the or key to select
current minutes.
8. Press DONE when completed.
PROGRAMMING
8
Altri manuali per RS9110
3
Indice
Altri manuali Robertshaw Termostato
Robertshaw
Robertshaw 8425 Manuale utente
Robertshaw
Robertshaw RS9220 Manuale utente
Robertshaw
Robertshaw 300-206 Manuale utente
Robertshaw
Robertshaw RS9320T Manuale utente
Robertshaw
Robertshaw 9620 Manuale utente
Robertshaw
Robertshaw 300-224 Specifiche tecniche
Robertshaw
Robertshaw RS321P Manuale utente
Robertshaw
Robertshaw 7700 Manuale utente
Robertshaw
Robertshaw 8425 Manuale utente
Robertshaw
Robertshaw RS8210 Manuale utente
Robertshaw
Robertshaw RS5220C Manuale utente
Robertshaw
Robertshaw smart 3000 Manuale utente
Robertshaw
Robertshaw RS6110 Manuale utente
Robertshaw
Robertshaw 9420 Manuale utente
Robertshaw
Robertshaw 9555 Manuale utente
Robertshaw
Robertshaw 8625 Manuale utente
Robertshaw
Robertshaw RS4110 Manuale utente
Robertshaw
Robertshaw RS6110 Manuale utente
Robertshaw
Robertshaw 9700 Manuale utente
Robertshaw
Robertshaw 9620 Manuale utente
