Robustel GoRugged M1000 Manuale utente

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 1 / 7

Robustel GoRugged M1000 UP Quick Guide

Chapter 1. Interface Introduction

1.1 Overview

1.2 LED Indicator

After inserting the SIM card into the modem and power on, the LED indicator’s status should be as follow when work

normally:

Name

Status

RUN

1.3 USB interface

USB

USB interface can be used for configuration, sending/receiving data and

power supply.

When USB interface of M1000 UP is used for

sending/receiving data as well as power supply, current/voltage output of

USB interface which connects to M1000 UP’s USB interface shall at least

reach to 1A/5V.

Note: Normally, current/voltage output of laptop’s USB 2.0 interface is only

0.5A/5V. So when you use USB interface for sending/receiving data, you

should use power input interface for power supply (please check section 1.4).

USB

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 2 / 7

1.4 Power Supply

The power supply range is 6 to 26 VDC.

Note: Please take care about the polarity, and do not make reverse connection.

Chapter 2. Hardware Installation

2.1 Insert/Remove SIM Card

SIM card is used for connecting to cellular network, you need buy SIM card from local operators.

Note:

1. Don’t touch the metal surface of the SIM card in case information in the card is lost or destroyed.

2. Don’t bend or scratch your SIM card. Keep the card away from electricity and magnetism.

3. A SIM card set with PIN code cannot be used normally in the gateway without the correct PIN code.

4. Make sure to disconnect the power source from your modem before inserting and removing your SIM card.



2.2 Connect the External Antenna (SMA Type)

Connect this to an external antenna with SMA male connector. Make sure the antenna is for the correct frequency as

your GSM/GPRS/UMTS/HSPA operator with impedance of 50ohm, and also connector is screwed tightly.

Screw tightly

Negative Polarity

Positive Polarity

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 3 / 7

2.3 Connect the Modem to External Device

User can use the USB cable to connect the modem’s Mini USB Connector to external slave devices / controller /

computer.

Note: User needs to install relevant USB driver to PC, which you can find out in the CD.

2.4 Power On and Connect with PC

Chapter 3. Operate the Modem

3.1 Install USB driver

1. In the Control Panel, when you install USB cable to PC, it will popup tab Other devices and show M1000 UP’s

module version.

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 4 / 7

2. Right-click to enter Properties and then click Update Driver.

3. Click Browse my computer for driver software.

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 5 / 7

4. Click Browse to locate the position of the USB driver which can be found out in the CD, then click Next.

5. After succeeding to install the USB driver, it will popup the following window.

6. A simulated virtual COM port which binds to the USB interface of M1000 UP will open after USB driver has been

installed. Please check “Device Manager”-> “Modems”.

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 6 / 7

7. Select the USB modem and right-click to enter “Properties”. In tab “Modem”, you will find that there is simulated

COM port which serial software such as secureCRT needs to connect to.

3.2 Start SecureCRT

We can enter AT commands to configure M1000 UP from serial software such as secureCRT, you can download this

software via link: https://app.box.com/s/arkn6xk1asgs1myvuuie.

1. Double click to open SecureCRT Potable.exe .

2. File->Connect->New Session

3. Select Protocol as “Serial”.

Robustel GoRugged M1000 UP Quick Guide

RT_QG_M1000 UP_v.1.0.0 25.01.2014 7 / 7

4. Select the simulated COM port and match the parameters as below, click the “Next” button to finish this session.

Note: You need to disable “RTS/CTS.

Note: Please refer to Robustel GoRugged M1000 UP User Guide to get more details about M1000’configuration.

Altri manuali per GoRugged M1000

Indice

Altri manuali Robustel Modem

Robustel

Robustel GoRugged M1000 Manuale utente

Robustel

Robustel GoRugged M1000 UP Manuale utente

Robustel

Robustel GoRugged M1000 MP Manuale utente

Robustel

Robustel GoRugged M1000 MP Manuale utente

Robustel

Robustel GoRugged M1000 XP Manuale utente

Robustel

Robustel GoRugged M1000 Manuale utente

Robustel

Robustel GoRugged M1000 Pro Manuale utente

Robustel

Robustel GoRugged M1000 MP Manuale utente

Robustel

Robustel GoRugged M1000 USBV2 Manuale utente

Robustel

Robustel GoRugged M1000 MP Manuale utente

Robustel

Robustel M1000 Pro V2 Manuale utente

Robustel

Robustel GoRugged M1000 MP Manuale utente

Robustel

Robustel GoRugged M1000 USB Manuale utente

Robustel

Robustel GoRugged M1000 Manuale utente

Robustel

Robustel GoRugged M1000 Manuale utente

Manuali Modem popolari di altre marche

Davicom

Davicom DM562AP Manuale utente

EpiValley

EpiValley TATA indicom SXC-1080 Manuale utente

Zte

Zte WiMAX Manuale utente

Intelimax

Intelimax MA-2060 Manuale utente

SMC Networks

SMC Networks D3CM1604V Manuale per l'uso e la cura

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manuale utente

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manuale utente

Samsung

Samsung AceLink SAM-335A Manuale utente

Enfora

Enfora Enabler-G Guida rapida alla configurazione

iRZ

iRZ ATM2-232 Manuale utente

Zhone

Zhone 6310 Manuale utente

Paradyne

Paradyne Hotwire 7976 Manuale utente

US Robotics

US Robotics 3453C Manuale utente

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manuale utente

Zte

Zte MF823 Manuale utente

Four-Faith

Four-Faith F1403 Manuale utente

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manuale utente

Gemtek

Gemtek WiMAX WIXFBR-103 Manuale utente