Rockwell Automation 1336 PLUS Manuale utente

Instructions

1336 PLUS & 1336 IMPACT™AC Drive

Main Control Board Replacement

Frames A - H

This publication will guide you through replacement of the Main Control

Board on 1336 PLUS and 1336 IMPACT AC Drives.

1. Remove and lock-out all incoming power to the drive.

2. Remove front cover or entire enclosure as required for adequate access.

3. If a HIM is installed, remove the module by sliding it down and out of

the cradle.

–A Frame Drives Only - Remove the screws securing the HIM cradle.

Remove the cradle and cable.

4. Remove the Language Module by carefully squeezing the sides-in, and

pulling outward.

5. If a Control Interface Board (L option) is installed, carefully remove the

board by loosening the 2 captive screws. Position the board and attached

wires off to the side of the chassis.

6. Label and remove any remaining cables/wires (note orientation) from the

board.

7. Remove the screws securing the Main Control Board. Remove the board

and set aside.

!ATTENTION: This drive contains ESD (Electrostatic

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing or

repairing this assembly. Component damage may result if ESD

control procedures are not followed. If you are not familiar with

static control procedures, reference publication 8000-4.5.2,

“Guarding Against Electrostatic Damage” or any other applicable

ESD protection handbook.

!ATTENTION: To avoid a shock hazard, assure that all power to the

drive has been removed before proceeding with the following

procedure. In addition, verify that the DC bus has discharged by

measuring across the “+DC” and “–DC” terminals of TB1 with a

voltmeter. The voltage should be 0.0VDC.

21336 PLUS & 1336 IMPACT™AC Drive Main Control Board Replacement

8. Install the replacement Main Control Board. Re-assemble components in

reverse order. If a Control Interface Board (L option) is not being used,

verify that the jumpers are correctly inserted (see the drive User Manual for

details).

Important: If your drive is a 1336 IMPACT (Frames B-H), attach the

supplied label to the chassis in the area shown below.

Important: When replacing connectors, it is essential that correct

alignment is verified. Particular attention should be paid to

ribbon cable connectors. Misalignment of connectors could

result in damage to the drive.

!ATTENTION: Replace any guards previously removed before

applying power to the drive. Failure to replace guards may result

in death or serious injury.

LANGUAGE MODULE

ALLEN-BRADLEY

LANGUAGE MODULE

ALLEN-BRADLEY

JOG

ESC SEL

JOG

ESC SEL

Frames A1 - A4 All Other Frames

Control Interface

(L Option) Board Control Interface

(L Option) Board

Language Module

Jumpers

Language Module

DANGER

Risk of electric shock and death.

Disconnect power, wait 5 minutes and

verify DC bus voltage before servicing.

Follow instructions in manual before use.

Earth ground required.

1336 IMPACT Drives

Attach label to chassis

above Main Control Board

336 IMPACT is a trademark of of Rockwell Automation, Inc.

Publication 1336 PLUS-5.67 – January, 2005 P/N 74103-909 (03)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Rockwell Automation Controllori

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Manuale utente

Rockwell Automation

Rockwell Automation SMC FLEX Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley LiquiFlo 2.0 Manuale utente

Rockwell Automation

Rockwell Automation 1756-L1 Manuale utente

Rockwell Automation

Rockwell Automation PowerFlex 525 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 7000 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix VP Series Manuale utente

Rockwell Automation

Rockwell Automation 1763-L16AWA Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley AADvance T9110 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley Logix 5000 Series Manuale del proprietario

Rockwell Automation

Rockwell Automation PowerFlex 40 Manuale utente

Rockwell Automation

Rockwell Automation External Dynamic Brake Kit Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley DriveLogix 5730 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley G Series Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley SMC Dialog Plus Manuale utente

Rockwell Automation

Rockwell Automation ALLEN-BRADLEY SMC-3 Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley 856T-B24LC Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley 1769 CompactLogix Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley 45MLA Manuale utente

Rockwell Automation

Rockwell Automation powerflex 4 Manuale utente

Rockwell Automation

Rockwell Automation SMC Dialog Plus Manuale utente

Rockwell Automation

Rockwell Automation MicroLogix 1500 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

3M MicroTouch EX113 Manuale utente