Rompa 18682 Manuale utente
Copyright ROMPA® Ltd
ELECTRIC AIR PUMP 18682, KH 2.06
ELECTRIC AIR PUMP 18682
CONTENTS
Your Electric Air Pump arrives in one box
containing:
•Pump with hard-wired cable and plug
•Deflation vent B
•Connector A
•Adapter C
USE
Read all the instructions thoroughly before use.
•This is a high-volume low-pressure pump. It is intended to inflate/deflate items e.g.
inflatable dingy, air mattress, large balls. It is not designed for continuous use. Extended
use over 30 minutes can cause the pump to overheat, causing damage to the pump.
•For use by a competent adult.
•Do not obstruct the inflation port D/deflation port Eand keep them well ventilated.
•For fast inflation and to shorten the amount of time the motor is in operation at one time,
always use the appropriate adapter Caccording to the valve size of the item you are
inflating.
•Refer to the instructions of the item you are inflating.
•Use (and store) in dry environments only.
•Do not allow sand, small stones etc to be sucked into the pump when using the pump.
•As with most electric air pumps, there is some noise when the pump is in use. This is
normal and to be expected.
To Inflate
•Plug in at electrical wall socket (AC 230V).
•Attach the adapter Cto the inflation port Dthrough the
connector A.
•Hold the pump against the valve of the inflatable item.
•Switch on to start inflation (switch to ‘I’).
•The valve of the inflatable item should not be
obstructed – otherwise it could overheat and damage
the pump.
•Never use the deflation vent Bwhen inflating the item.
•On large items such as inflatable dingys, king-size air mattresses etc, the pump should fit
directly onto the valve of the inflatable item. Otherwise, use the appropriate adapter Cfor
smaller valves e.g. with balls, single-size air mattresses.
•For inflatable items with screw-type valves, remove these as necessary.
•Switch off F(switch to ‘O’) after use.
Copyright ROMPA® Ltd
ELECTRIC AIR PUMP 18682, KH 2.06
ToDeflate
•Plug in at electrical wall socket (AC 230V).
•Open the valve of the inflated item.
•Attach the adapter to the deflation port through
the deflation vent Bthen insert it into the valve.
•Switch on to start inflation (switch to ‘I’).
•The valve of the inflatable item should not be
obstructed – otherwise it could overheat and
damage the pump.
•For inflatable items with small valves, pinch the
valve between your fingers to open the flap of the
valve and allow air to escape.
•For inflatable items with screw-type valves, remove these as necessary
•Switch off F(switch to ‘O’) after use.
CARE & MAINTENANCE
Handle the pump with care, observing the advice in these instructions.
SAFETY
Always supervise the use of this product
For use by a competent adult
Do not expose to rain/damp.
Store indoors, in a safe place, out of reach of children/anyone you would not want to find it.
Do not operate the pump for more than 30 minutes at one time.
Do not allow to overheat.
Do not use an extension cable
Should you damage the cord/pump, contact a suitably qualified electrician. Cease use till
repaired/replaced.
Do not exceed the given pressure/size of the item you are inflating. Otherwise injury could
result as the item bursts.
Never leave the pump unattended whilst it is plugged in/in use.
Use (and store) in dry environments only.
Never look inside or point the inflation port D/deflation port Etowards eyes when the pump is in
operation.
Never attempt to put hands or fingers into the inflation port D/deflation port Eat any time.
SPECIFICATION
AC 230V
Indice
Altri manuali Rompa Pompa dell'acqua
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente