Ronstan Andersen 18ST FS Manuale utente

PRODUCT MANUAL

18ST FS (V.1.0.F)

RON-WPM-710218-18STFS-Rev.2

EXPLODED VIEW

3.1

3.2

3.1

3.2

3.4

POS. 3 - 537551

POS. 3 - 537511

3.3

18ST FS (V.1.0.F)

PARTS LIST

ITEM NO. QTY. DESCRIPTION PART NO.

1 3 Screw ISO 7380-A4-M5x12

2 1 Self-tailing arm 786100

3 1 Self-tailing top complete

Model ST 537551

3 1 Self-tailing top complete

Model ST FS 537511

3.1 1 Circlip 726400U

3.2 1 Top ring 782100

3.3 6 Screw 781811

3.4 1 Disc

Model ST (537551 only) 726310

4 1 Drum complete 773600

5 1 Drive shaft complete 786000

6 4 Arm spring 713300

7 4 Pawl 713200

8 1 Bearing 785700

9 1 Bushing (not removable) 716501

10 1 Ratchet gear 785900

11 1 Shaft 785300

12 1 Bushing RD786300

13 1 Gear wheel 786200

14 1 Base 773700

15 1 Bushing for ratchet gear 785500

16 1 Shaft for ratchet gear 785100

1 Service kit 18 (not included) 710018

18ST FS (V.1.0.F)

MOUNTING INSTRUCTIONS

PAWL SPRING MOUNTING

Installing the winch is easy, if you follow these instructions. The numbers in ( ) refer to the

position numbers in the parts list.

Tools required for the installation:

• Allenkey(3mm)

• Allenkey(5mm)

• Ø6.5mm.(1/4”)drill

• Beddingcompound

1. Remove screws (1).

2. Remove self-tailing arm (2) and drum (4).

3. PlacethetemplateanddrillholesØ6.5mm(1/4”).

Makesurethatnodustcomesintocontactwiththewinchwhiledrilling.

4. Apply a light coat of bedding compound, ensuring that each bolt hole is bedded.

Keep drain grooves clear.

5. Fastenbase(14)intoplaceusing6pieces.M6(1/4”)countersunkheadscrews.

Uselargewashersorabackingplate.

6. Assemble in reverse order.

7. Checkthatthewinchisfunctioningcorrectly:

-Thedrumshouldoperatesmoothly,byturningthedrumclockwisebyhand.

-Thedrummustnotturnwhentryingtoturnthedrumanticlockwise.

-Whileturningthewinchhandleclockwisethedrumshouldturn.

-Whileturningthewinchhandleanticlockwisethedrumshouldnotturn.

• 6xM6(1/4”)countersunkheadscrewsandcorresponding

nuts(lengthdependingondeckthickness).

• 6xlargewashersorbackingplate

• Ringspannertomatchnuts

Note the curved

spring“arm”

18ST FS (V.1.0.F)

SERVICE INSTRUCTIONS

• Allenkey(3mm)

• ANDERSENwinchgrease

Tools required for service:

• Screwdriver(large)

• Screwdriver(small)

• Winchhandle

1. Remove screws (1).

2. Remove self-tailing arm (2).

3. Remove drum (4).

4. Pull up the drive shaft (5) gently, using the winch handle.

5. Remove pawls (7) and springs (6).

6. Remove shaft (11) and pull out gearwheel (13).

7. Lift up ratchet gear (10) and pull it out through hole in base (14).

8. Clean all parts in benzine including gear teeth.

9. Assemble in reverse order. During assemble, by the use of a small soft brush lightly grease

all gear teeth, drive shaft, roller bearing, shafts, pawls, springs and bushings. Pawls should

onlybelubricatedwithaverythinlmofANDERSENWINCHGREASE.Itisveryimportant

that pawls can move freely.

IMPORTANT: Whenassemblingthewinch,checkthefunctioningofeachpawlbypushing

the pawl against the spring. The pawls should move smoothly and automatically return to

their normal position, where the pawls engage with the teeth. If the pawls do not function

correctly,cleanandlubricatethepawlsandgears.Checkthefunctionofthepawlsagainto

makesurethatitworkscorrectly.Ifthepawlsdonotworkcorrectlyreplacethespringsand

recheckthefunctioning.

Malfunctioning pawls may lead to unexpected release of the winch force resulting in fatal

injuries to the user and others.

ServiceKitNo:18(part.no.710018)containssparepartsforthesewinches.

Maintenance instructions for PVD coated stainless steel surfaces.

PVD-coated surfaces should be rinsed regularly in fresh water to remove any salt residue, dirt

orothercontaminantsanddriedgentlywithasoftcloth.Toremovegreaseorothermarks,a

mild abrasive free cleaning agent such as spray-on glass cleaning solution may be used. No

caustic detergents or other aggressive or abrasive cleaning agents should ever be used, as

they may damage the surface.

18ST FS (V.1.0.F)

GENERAL INFORMATION

Due to the best choice of materials and high precision in manufacturing, we recommend, for

normal use, only to dismantle, clean and lubricate the winch once every second year. Under

extensive use, such as racing, charter or blue water sailing, we recommend to lubricate the

winch once every year.

WestronglyrecommendalwaystouseANDERSENWINCHGREASE,whenlubricatingyour

winch.ANDERSENWINCHGREASEisahighqualitysilicone/Teongreaseproduct.

Mostothertypesofgrease,including“marinegrease”arenotsuitableforlubricationof

winches. Non-suitable grease products can cause malfunction, which could result in fatal

injuries for the user and others.

Pawl arm springs should be replaced every second year. Spare arm springs and other parts

thatmayberequiredareincludedintheANDERSENServiceKit.Pleaserefertotheservice

instruction for the Service Kit suitable for the speciﬁc winch.

When the winch handle is not in use but the winch is under load, we recommend, from a

safety point of view, to remove the winch handle from the winch.

To ensure correct function of the self-tailing unit, only use recommended line sizes. When

using the winch with mooring lines DO NOT use the self-tailing function and be sure that the

mooring line is not in contact with the self-tailing arm.

To ensure the best possible functioning of the winch, we recommend that

the winch is placed in accordance with the line entry (shown below).

Be also aware that the self-tailing arm is positioned correctly. We recommend to have the

self-tailing arm positioned within the shaded area (shown above). On this model the self-

tailing arm can be placed in several dierent positions after having installed the winch.

To identify the Output Drive Gear, insert a winch handle into the winch

androtateinbothdirections,thedrivegearwillonlyrotateclockwise

in a fast and slow speed.

Ideal

rope

entry

Output

drive

gear

18ST FS (V.1.0.F)

SAFETY NOTICES

ALLWINCHES

DO NOT DISCARD

Failure to observe these precautions

could result in serious injury or death.

Read All Safety Notices and Product Manuals

Do not install or operate this winch before reading and fully understanding the contents of

this Product Manual.

Stay Alert When Operating

Andersen winches are very powerful and have the potential to cause signiﬁcant damage

and/orseriousinjuryifusedimproperlyorwithoutduecautionandvigilance.

Operators Must be Trained

Helppreventsignicantdamageand/orseriousinjurybyensuringanypersonoperatinga

winch has a thorough understanding of its proper operation and is aware of the potential

hazards involved. As a minimum, all winch operators must read and understand this Safety

Notice Sheet and the Product Manual.

Particularattentionisdrawntothefollowingpoints:

• Childrenandothersnotqualiedtooperateanelectricwinchmustbekeptatasafe

distance from the winch and any rigging or ﬁttings that are under load.

• Longhairand/orlooseclothingmustbetiedbacktoavoidbeingcaughtinthewinch.

• In the event of a rope override or other fault, stop the winch and turn o power before

attempting to resolve the problem.

Avoid Accidental Operation

Remove winch handles and turn o power to the winch when not in use to help avoid

unsupervised or unintentional operation. Failure to do so could result in signiﬁcant

damageand/orseriousinjury.

Maintenance

Turnopowertothewinchbeforeperforminganymaintenanceorservicetasks.Failure

todosocouldresultinsignicantdamageand/orseriousinjury.

Lifting Operations

Thewinchmustnotbeoperatedwiththeropeintheselftailerwhenusedinanykindof

lifting operation.

Any lifting operations should be conducted by two persons in order to maintain constant

visual contact with the object being lifted.

Furthermore the self tailer must not be used as a cleat for a rope used to lift or suspend

any object. The rope must be secured properly by tying o, or leading to a suitable ﬁtting

such as a cleat or bollard.

18ST FS (V.1.0.F)

Visit www.andersenwinches.com

Visitwww.ronstan.com/warranty

Manufactured by Ronstan Denmark ApS.

Jægervænget36-7100Vejle-Denmark

o[email protected]-www.andersenwinches.com

WORLDWIDE DISTRIBUTION & SERVICE

WARRANTY

18ST FS (V.1.0.F)

PRODUCT MANUAL

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ronstan Verricello

Ronstan

Ronstan ORBIT WINCH 30QT Manuale utente

Ronstan

Ronstan BB Orbit Block 20 Series Manuale utente

Ronstan

Ronstan Andersen 28ST Manuale utente

Ronstan

Ronstan ANDERSEN Compact Motor 58ST Manuale utente

Ronstan

Ronstan Andersen 40ST Manuale utente

Ronstan

Ronstan Andersen Compact Motor 52ST Manuale utente

Ronstan

Ronstan Andersen Compact Motor 68ST Manuale utente

Ronstan

Ronstan Andersen 28ST FS Manuale utente

Ronstan

Ronstan Andersen 34ST Manuale utente

Ronstan

Ronstan ORBITBLOCKS Manuale utente

Ronstan

Ronstan ORBIT WINCH RA6402 40QT Manuale utente

Ronstan

Ronstan ANDERSEN Classic 10 Manuale utente

Ronstan

Ronstan Andersen Compact Motor 46ST Manuale utente

Ronstan

Ronstan Compact Motor 68/72ST Manuale utente

Ronstan

Ronstan Andersen 12ST Manuale utente

Ronstan

Ronstan ORBIT Series Manuale utente

Ronstan

Ronstan ORBIT WINCH 20ST Manuale utente

Ronstan

Ronstan ORBIT WINCH 40QT Manuale utente

Manuali Verricello popolari di altre marche

WARRIOR

WARRIOR Trojan 40PUS12 Guida di riferimento rapido

SVERO

SVERO 16 Manuale utente

Warrior Winches

Warrior Winches C10000NH Manuale utente

Badland Winches

Badland Winches 68146 Manuale utente

Bush

Bush II Series Manuale utente

Badland

Badland APEX 5500 Manuale utente

Quadratec

Quadratec Q9000 Synthetic Manuale

C-Max

C-Max VIGO Manuale utente

Comeup

Comeup DV-9 Manuale utente

Orvea

Orvea Italwinch 805 Manuale utente

Prowinch

Prowinch PWJTHF300 Manuale utente

Clas Ohlson

Clas Ohlson LD2000-A Manuale utente

Topex

Topex 97X080 Manuale utente

Eastbound

Eastbound MotoWinch 1707001 Manuale utente

Runva

Runva EWD8000 Guida di riferimento rapido

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Guida all'installazione

Granit

Granit 11157675 Manuale utente

TREX

TREX TB75 Manuale utente