Ross pro-xi 100 Manuale utente
Workstation Integrator Cabling Guide
pro-xi® 100
pro-xi 100 · Cabling Guide
• Ross Part Number: PRO100DR-008-02
• Release Date: May 8, 2019.
The information contained in this manual is subject to change without notice or obligation.
Copyright
©2019 Ross Video Limited, Ross®, and any related marks are trademarks or registered trademarks of Ross Video Limited. All other
trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All rights reserved. No part of this
publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying,
recording or otherwise, without the prior written permission of Ross Video. While every precaution has been taken in the preparation
of this document, Ross Video assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Trademark Information
pro-xi® is a registered trademarks of Ross Video or its affiliates in the United States and other countries.
All other trademarks and service-marks are the property of their respective owners.
The various backgrounds, icons, logos, wallpaper and other associated trade dress displayed in the screen-shots are the property of
their respective owners.
Patents
Patent numbers US 7,034,886; US 7,353,458; US 7,496,846 B2; US 7,508,455; US 7,602,446; US 7,770,131; US 7,779,361; US
7,802,802 B2; US 7,834,886; US 7,914,332; US 8,307,284; US 8,407,374 B2; US 8,499,019 B2; US 8,519,949 B2; US 8,743,292
B2; GB 2,419,119 B; GB 2,447,380 B; JP 4891782; and other patents pending.
Limited Rights
The software described in this document is “commercial computer software” provided with restricted rights (except for the included
open/free source) as specified in the FAR 52.227-19 and/or the DFAR 227.7202, or successive sections. Use beyond license
provisions is a violation of worldwide intellectual property laws, treaties and conventions. This document is provided with limited
rights as defined in 52.227-14.
The electronic (software) version of this document was developed at private expense; if acquired under an agreement with the USA
government or any contractor thereto, it is acquired as “commercial computer software” subject to the provisions of its applicable
license agreement, as specified in (a) 48 CFR 12.212 of the FAR; or, if acquired for Department of Defense units, (b) 48 CFR
227-7202 of the DoD FAR Supplement; or sections succeeding thereto. Contractor/manufacturer is Ross Video 8 John Street,
Iroquois, Ontario, Canada, K0E 1K0.
Disclaimer
Information in this document is provided in connection with Ross Video products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in Ross Video Terms and Conditions of
Sale for such products, Ross Video assumes no liability whatsoever, and Ross Video disclaims any express or implied warranty,
relating to sale and/or use of Ross Video products including liability or warranties relating to fitness for a particular purpose,
merchantability, or infringement of any patent, copyright or other intellectual property right.
Ross Video products are not designed, intended or authorized for use in any medical, life saving, or life sustaining applications or for
any other application in which the failure of the Ross Video product could create a situation where personal injury or death may occur.
Ross Video may make changes to specifications and product descriptions at any time, without notice.
Although every effort has been made to ensure that the information in this document is correct and complete, Ross Video or its
affiliates shall not be held liable for any errors, inaccuracies, or omissions found in this manual.
Notice
The material in this manual is furnished for informational use only. It is subject to change without notice and should not be construed
as commitment by Ross Video Limited. Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may
appear in this manual.
Safety Notices
Refer to the “Important Regulatory and Safety Notices” document that accompanied your product.
Statement of Compliance
This product has been determined to be compliant with the applicable standards, regulations, and directives for the countries where
the product is marketed.
Compliance documentation, such as certification or Declaration of Compliance for the product is available upon request by
contacting techsupport@rossvideo.com. Please include the product; model number identifiers and serial number and country that
compliance information is needed in request.
EMC Notices
United States of America - FCC Part 15
This equipment has been tested and found to comply with the limits for a class A Digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
Commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Canada
This Class A device complies with Canadian ICES-003 and part 15 of the FCC Rules.
Cet appariel numerique de la classe “A” est conforme a la norme NMB-003 du Canada.
European Union
This equipment is in compliance with the essential requirements and other relevant provisions established under regulation (EC) No
765/2008 and Decision No 768/2008/EC referred to as the “New Legislative Framework”.
International
This equipment has been tested under the requirements of CISPR 22:2008 or CISPR 32:2015 and found to comply with the limits for
a Class A Digital device.
Emissions Certifications
EN 55022:2010
FCC Part 15, Class A
ICES-003, Issue 5
AS/NZS CISPR 22:2009
Immunity Certifications
Notice — Changes or modifications to this equipment not expressly approved by Ross Video Ltd. could void the
user’s authority to operate this equipment.
Warning — This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may
cause radio interference.
Notice — This is a Class A product. In domestic environments, this product may cause radio interference, in which
case the user may have to take adequate measures.
EN 55024:2010
EN 61000-3-2:2006 + A1:2009 + A2:2009
EN 61000-3-3:2008
Safety Certifications
IEC 60950-1:2005(Second Edition) +
AM 1:2009 + AM 2:2013
EN 60950-1:2006/A11:2009/A1:2010
CE Certifications
EMC Directive 2004/108/EEC
Low Voltage Directive 2006/95/EC
FCC Certifications
Part 15 of the FCC Rules
USA Notification
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own
expense.
Maintenance/User Serviceable Parts
Routine maintenance to this Ross product is not required. This product contains no user serviceable parts. If the module does not
appear to be working properly, please contact Technical Support using the numbers listed under the section “Contacting Technical
Support” on page 12. This product is covered by a generous 1-year warranty and will be repaired without charge for materials or
labor within this period. See the section “Warranty and Repair Policy” on page 123 for details.
Environmental Information
The equipment may contain hazardous substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural
resources, Ross Video encourages you to use the appropriate take-back systems. These systems will reuse or recycle most of the
materials from your end-of-life equipment in an environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste
administration. You can also contact Ross Video for more information on the environmental performances of our products.
pro-xi 100 Cabling Guide (v2.0) Cabling the pro-xi 100 • 5
Cabling the pro-xi 100
This guide provides interconnect diagrams and examples of how to cable single-head and dual-head setups.
Before You Begin
Keep the following in mind when cabling your system:
• If the connected computer systems output a VGA video signal, a VGA-to-DVI-I adapter is required.
• If the connected computer system outputs an HDMI video signal, an HDMI-to-DVI-D adapter is required.
• If the pro-xi 100 outputs are connected to HDMI monitors or KVM TX units that utilize HDMI, then the
appropriate cable or adapter is required.
Direct Keyboard and Mouse
Figure 1 illustrates an operator station with a direct keyboard and mouse connection to the pro-xi 100 system.
Figure 1 Operator Station — Direct Keyboard and Mouse
Single-Head Direct Monitor
Figure 2 illustrates an operator station with a direct monitor connection to the pro-xi 100 system.
Figure 2 Operator Station — Single-Head Direct Monitor
CTC
USB1USB2USB3
pro-xi 100 Workstation Integrator
VOC 1
USB1USB2USB3
pro-xi 100 Workstation Integrator
6 • Cabling the pro-xi 100 pro-xi 100 Cabling Guide (v2.0)
Dual-Head Direct Monitor
Figure 3 illustrates an operator dual-head station with a direct connections to the pro-xi 100 system.
Figure 3 Operator Station — Dual-Head Monitors
Single Output (Single-Head) Direct Keyboard, Video, and Mouse
Figure 4 illustrates the cabling required to connect a computer system to the pro-xi 100 system.
Figure 4 Single Output, Single-Head Connections
VOC 1 VOC 2
USB1USB2USB3
Left Monitor
Right Monitor
pro-xi 100 Workstation Integrator
ISC 1
USB USB
USB B-to-A Cable (5m max.)
USB B-to-A Cable (5m max.)
DVI-I or VGA Cable (5m max.)
3.5mm Stereo Audio Cable
Computer for Controlled System
AUDIO
OUT
VIDEO
OUT 1 VIDEO
OUT 2
pro-xi 100 Workstation Integrator
pro-xi 100 Cabling Guide (v2.0) Cabling the pro-xi 100 • 7
Dual Output (Dual-Head) Direct Keyboard, Video, and Mouse
Figure 5 illustrates the cabling required to connect a computer system to the pro-xi 100 system.
Figure 5 Dual Output, Dual-Head Connections
Interconnect, Single-Head Operator Station KVM Extender
Figure 6 illustrates a single-head operator station with the pro-xi 100 system and KVM Extenders.
Figure 6 Operator Station — Single-Head with KVM Extender
ISC 1 ISC 2
USB USB
USB B-to-A Cable (5m max.)
USB B-to-A Cable (5m max.)
Right Monitor
DVI-I or VGA Cable (5m max.)
Left Monitor
DVI-I or VGA Cable (5m max.)
3.5mm Stereo Audio Cable
Computer for Controlled System
AUDIO
OUT
VIDEO
RIGHT VIDEO
LEFT
pro-xi 100 Workstation Integrator
VOC 1CTC
USB1USB2USB3
3.5mm Stereo Audio Cable
Single-Head KVM Extender (TX)
AUDIO USB
KVM Extender Pair
(USB A-to-B Cable)
Left DVI-D Input
KVM Extender Connection
Copper to 100m
Fiber to 40km
pro-xi 100 Workstation Integrator
Single-Head KVM Extender (RX)
AUDIO USB USB
8 • Cabling the pro-xi 100 pro-xi 100 Cabling Guide (v2.0)
Interconnect, Dual-Head Operator Station KVM Extender
Figure 7 illustrates a dual-head operator station with the pro-xi 100 system and two KVM Extenders.
Figure 7 Operator Station — Dual-Head with KVM Extender
VOC 1 VOC 2CTC
USB1USB2USB3
3.5mm Stereo Audio Cable
Dual-Head KVM Extender (TX)
AUDIO USB
Left DVI-D Input
Right DVI-D Input
KVM Extender Connection
Copper to 100m
Fiber to 40km
Dual-Head KVM Extender (RX)
AUDIO
Left Monitor
Right Monitor
pro-xi 100 Workstation Integrator
USB USB
KVM Extender Pair
(USB A-to-B Cable)
pro-xi 100 Cabling Guide (v2.0) Cabling the pro-xi 100 • 9
Single Video (Single-Head) KVM Extender
Figure 8 illustrates a single video operator station with the pro-xi 100 system and two KVM Extenders.
Figure 8 Operator Station — Single Output (Single-Head) with KVM Extenders
ISC 1
KVM Extender Connection
Copper to 100m
Fiber to 40km
DVI-I or VGA Cable (5m max.)
DVI-I or VGA Input
3.5mm Stereo Audio Cable
3.5mm Stereo Audio Cable
Single-Video KVM Extender (RX)
AUDIO USB USB
pro-xi 100 Workstation Integrator
Computer for Controlled System
USB USB
AUDIO
OUT
VIDEO
OUT 1 VIDEO
OUT 2
Single-Video KVM Extender (TX)
AUDIO USB
Keyboard
Input
Mouse Input
KVM Extender Pair
(USB A-to-B Cable)
10 • Cabling the pro-xi 100 pro-xi 100 Cabling Guide (v2.0)
Dual Output (Dual-Head) Using Single-Head KVM Extenders
Figure 9 illustrates a dual video output station with the pro-xi 100 system and two KVM Extenders.
Figure 9 ISC Interconnect — Dual Output (Dual-Head) with Single-Head KVM Extenders (2 Pairs)
ISC 1 ISC 2
Single-Head KVM Extender (RX)
AUDIO USB USB
DVI-I or VGA Cable
DVI-I or VGA Cable
3.5mm Stereo Audio Cable
USB USB
Computer for Controlled System
AUDIO
OUT
VIDEO
RIGHT VIDEO
LEFT
pro-xi 100 Workstation Integrator
Single-Head KVM Extender (TX)
AUDIO USB
Single-Head KVM Extender (RX)
AUDIO
Keyboard Mouse
USB USB
Single-Head KVM Extender (TX)
AUDIO USB
KVM Extender Connection
Copper to 100m
Fiber to 40km
KVM Extender Connection
Copper to 100m
Fiber to 40km
KVM Extender Pair
(USB A-to-B Cable)
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Ross Scrivania
