Ross Vision Octane QMD-X Manuale utente
Ross Video Limited
Octane™/QMD-X Rack Mount Arms
Installation Guide
2
Octane/QMD-X Rack Mount Arms Installation Guide
• Ross Part Number: 4800DR-344-02
• Release Date: July 13, 2011. Printed in Canada.
The information contained in this guide is subject to change without notice or
obligation.
Copyright
© 2010 Ross Video Limited. All rights reserved.
Contents of this publication may not be reproduced in any form without the
written permission of Ross Video Limited. Reproduction or reverse engineering
of copyrighted software is prohibited.
Patents
This product is protected by the following US Patents: 4,205,346; 5,115,314;
5,280,346; 5,561,404; 7,034,886; 7,508,455. This product is protected by the
following Canadian Patents: 2039277; 1237518; 1127289. Other patents
pending.
Notice
The material in this guide is furnished for informational use only. It is subject to
change without notice and should not be construed as commitment by Ross
Video Limited. Ross Video Limited assumes no responsibility or liability for
errors or inaccuracies that may appear in this guide.
Trademarks
•is a registered trademark of Ross Video
Limited.
• Ross, ROSS, ROSS®, MLE, Vision, and Octane are registered or
unregistered trademarks of Ross Video Limited.
•All other product names and any registered and unregistered
trademarks mentioned in this guide are used for identification
purposes only and remain the exclusive property of their
respective owners.
3
Important Regulatory and Safety Notices to Service
Personnel
Before using this product and associated equipment, refer to the “Important
Safety Instructions” listed here and in the front of the Vision Engineering
Manual, to avoid personnel injury and to prevent product damage.
Products may require specific equipment, and/or installation procedures to be
carried out to satisfy certain regulatory compliance requirements. Notices have
been included in these publications to call attention to these specific
requirements.
Important Safety Instructions
Use only manufacturer approved Power Supplies and Power Cords supplied
with this product.
The power supply adapter(s) included with this product use a protective earth
connection to reduce the risk of electrical shock to the operator and or service
personnel. A grounding conductor in the equipment's supply cord provides this
protective earth connection and must be reliably connected to a facilities
protective earth.
Do not defeat safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The third prong is provided for
your safety. If the provided plug does not fit in to your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the product’s power cord(s) and replace any cord(s) which shows signs
of physical damage or ware.
The product's power supply cord(s) is (are) used as a means to disconnect the
power supply from the AC Mains. Ensure either the appliance inlet or the mains
plug of the power supply cord, remains readily operable.
This product is designed for Indoor Use:
“WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPERATUS TO RAIN OR MOISTURE”.
General Handling Guidelines
• Careful handling, using proper ESD precautions, must be observed.
• Power down the system before PCB removal.
4
ESD Susceptibility — Avoid handling the switcher circuit
boards in high static environments such as carpeted areas, and
when synthetic fiber clothing is worn. Touch the frame to
dissipate static charge before removing boards from the frame,
and exercise proper grounding precautions when working on
circuit boards.
Environmental Information
The equipment that you purchased required the extraction and use
of natural resources for its production. It may contain hazardous
substances that could impact health and the environment.
To avoid the potential release of those substances into the environment and to
diminish the need for the extraction of natural resources, Ross Video encourages
you to use the appropriate take-back systems. These systems will reuse or
recycle most of the materials from your end-of-life equipment in an
environmentally friendly and health conscious manner.
The crossed-out wheeled bin symbol invites you to use these systems.
If you need more information on the collection, reuse, and recycling systems,
please contact your local or regional waste administration.
You can also contact Ross Video for more information on the environmental
performances of our products.
Package Contents • 5
Package Contents
The contents of each Octane/QMD-X Rack Support kit are listed below. If any
items are missing, or damaged, contact Ross Video Technical Support.
Qty Part# Item
2 4800FR-755 Rack Mount Arms
24800FR-756 Rail Guides
4 650-017R 5/16 Hex Nut
2127-009R Threaded Rubber Bumper
6 • Rack Mount Arms Installation
Rack Mount Arms Installation
Notice — Failure to install both the Support Brackets as described will
void the warranty.
1. Install the Octane/QMD-X frame into the rack according to the
instructions provided with the equipment rack.
2. Install the Rack Mount Arm (4800FR-755) onto the side of the
Octane/QMD-X frame by fitting it over the locking pins and sliding it
away from the back of the frame to lock it into position (Figure 2).
The end of the Rack Mount Arm should extend past the rear rack rail
by about 1/2 inch (1.27cm).
Figure 1 Rack Mount Arm Installation
3. Install the Rail Guide (4800FR-756) over the end of the Rack Mount
Arm so that the two retaining bolts on the Rack Mount Arm pass
through the slots on the Rail Guide (Figure 2).
Figure 2 Rail Guide Installation
4. Use standard rack mounting bolts (not supplied) to secure the Rail
Guides to the rear rack rails.
5. Use the 5/16 Hex Nuts (650-017R) to secure the Rail Guides to the
Rack Mount Arms (Figure 3).
Rack Mount
Arm
Unlocked
Locked
Rail Guide
Retaining
Bolts
Rack Mount
Arm
Rack Mount Arms Installation • 7
Figure 3 Hex Nut Installation
6. Install the Threaded Rubber Bumpers (127-009R) into the Rack
Mount Arms to prevent the arms from separating from the frame.
Figure 4 Threaded Rubber Bumper Installation
5/16 Hex
Nuts
Threaded Rubber
Bumpers
Contact Us
Contact our friendly and professional support representatives for the
following:
• Name and address of your local dealer
• Product information and pricing
• Technical support
• Upcoming trade show information
Visit Us
Please visit us at our website for:
• Company information
• Related products and full product lines
• On-line catalog
•News
• Testimonials
PHONE
General Business Office
and Technical Support 613 • 652 • 4886
After Hours Emergency 613 • 349 • 0006
Fax 613 • 652 • 4425
E-MAIL General Information [email protected]
POSTAL
SERVICE
Ross Video Limited 8 John Street,
Iroquois, Ontario, Canada
K0E 1K0
Ross Video Incorporated P.O. Box 880,
Ogdensburg, New York, USA
13669-0880
Indice
Altri manuali Ross Rack e supporto
