Rosslare AY-B1663 Manuale utente

Swipe Match-on-Card Family Readers

Installation Manual

November 2009

Models:

AY-B1663

AY-B4663

Table of Contents

Swipe Family Readers Installation Manual Page ii

Table of Contents

1Introduction............................................................................... 3

2General Overview ..................................................................... 5

2.1 Features..............................................................................5

3Technical Specifications ........................................................... 6

4Mounting Instructions.............................................................. 8

5Wiring Instructions..................................................................10

6Configuring the Reader...........................................................11

6.1 Configuration Procedure...................................................11

7Testing the Reader...................................................................12

8Modes of Operation .................................................................13

8.1 Boot Mode........................................................................13

8.2 Configuration Mode .........................................................13

8.3 Standby Mode..................................................................13

8.4 Read Mode ......................................................................14

8.4.1 Valid Card / Fingerprint Read......................................14

8.4.2 Invalid Card / Fingerprint Read ...................................14

8.5 Lockout Mode...................................................................15

Appendix A Limited Warranty ...................................................16

Appendix B Technical Support ...................................................18

Introduction

Swipe Family Readers Installation ManualPage 3

1Introduction

Mifare® Smart Card Fingerprint Swipe Sensor MOC (Match-On-

Card technology, developed by Rosslare) Readers are

biometric fingerprint readers that are used with access control

systems. The Mifare® Smart Card Fingerprint Swipe Sensor MOC

Reader Family includes the following readers:

•AY-B4663

•AY-B1663

Figure 1: AY-B1663 Snail Mifare® Smart Card and Fingerprint Swipe

Introduction

Swipe Family Readers Installation Manual Page 4

Figure 3: AY-B4663 Rambo Mifare® Smart Card and Fingerprint Swipe

This Installation Manual contains the following information:

•

Overview

•

Technical Specifications

•

Mounting Instructions

•

Wiring Instructions

•

Configuring the Reader

•

Testing the Reader

•

Modes of Operation

General Overview

Swipe Family Readers Installation ManualPage 5

2General Overview

Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers use

a Swipe type biometric sensor to check for 1:1 verification

between fingerprint data and a biometric template stored in a

Mifare®card. When verification is confirmed, the Reader then

transmits the Card ID or any ID stored in sector 0 or 15 to the

Access Controller, which compares the card ID to data stored

in the database and decides access granting.

The Readers are compatible with most Access Control

hardware, including the following hardware manufactured by

Rosslare Security Products: AC-015, AC-115, AC-020, AC-215,

AC-225, and AC-525.

2.1 Features

Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers

include the following features:

•3 different designs to accommodate customer

requirements and preferences

•3 blue LEDs that flash in a pattern that leads users to swipe

fingers in the correct direction

•Designed for indoor use (swipe sensor protection required

for outdoor use)

•Support Back Tamper sensor and Tamper output signal

•Support Lockout feature for increased security

•Compatible with Mifare®(ISO 14443A) 1K and 4K cards

•Mifare®card followed by finger swipe reading

•Reads up to 2 fingerprint templates stored on the card

•Programmable data transmission formats

•Programmable LED control and buzzer control inputs

•Tamper output

•Compliant with the CE, UL, and FCC standards for

international distribution

Technical Specifications

Swipe Family Readers Installation Manual Page 6

3Technical Specifications

General Characteristics

Model Numbers •AY-B4663

•AY-B1663

Output Formats •Wiegand 26 (default)

•Wiegand 26 with facility code

•Wiegand 32 reversed

•Clock & Data

•Wiegand 32

•Wiegand 34

•Wiegand 40

Read Range (max) 4 cm (1.6 inches)

Electrical Characteristics

Power Supply Type Linear type - recommended

Input Voltage 5 - 16VDC

Absolute Maximum

(non-operating) 18VDC

Maximum Input

Current Standby: 85 mA @ 12VDC

Read: 300 mA @ 12VDC

Tamper Output Open collector, active low,

max. sink current 32mA

Maximum

Controller

Cable Distance

150 m (500 ft)

(using 18AWG shielded cable)

Frequency 13.56 MHz

Card Compatibility Mifare® ISO14443A-3 standard

Technical Specifications

Swipe Family Readers Installation ManualPage 7

Environmental Characteristics

Operating Temp.

Range -25°C to 60°C

-13°F to 140°F

Storage Temp.

Range -40°C to 85°C

-40°F to 140°F

Operating Humidity 5% – 95% (non-condensing)

Dimensions

Reader Height x Width x Depth Weight

AY-B1663 85.4 x 50.6 x 27 mm

3.36 x 1.99 x 1.06 inch 65 g

2.3 oz.

AY-B4663 70.1 x 54.1 x 39.1 mm

2.76 x 2.13 x 1.54 inch 90 g

3.2 oz.

Mounting Instructions

Swipe Family Readers Installation Manual Page 8

4Mounting Instructions

Prior to starting, select the location where the controller unit is

to be mounted. Use the supplied drilling template to assist in

locating and drilling the appropriate holes.

AY-B1663

AY-B4663

Figure 4: Mounting orientations

Note:

Be sure to protect the swipe sensor when the Reader is

mounted outside.

To mount the Reader:

1. Determine an approximate surface location for the

Reader.

2. Peel off the back of the self-adhesive mounting label

template and place it on the required mounting location.

3. Using the template as a guide, drill two holes (of the size

indicated on the template) on the surface to mount the

Reader.

4. Insert a suitable wall plug into each hole.

5. Drill a 7/16” (10 mm) hole for the cable. If the surface is

metal, place a grommet or electrical tape around the

edge of the hole.

6. Unscrew and remove the case security screw at the

bottom using the security hex key.

Mounting Instructions

Swipe Family Readers Installation ManualPage 9

7. Carefully remove the snap-off front cover of the Reader to

reveal two screw holes.

AY-B1663

AY-B4663

Figure 5: Removing the Top Cover

8. Route the interface cable from the Reader to the

Controller.

Note:

The Reader can also be mounted using strong epoxy glue.

After application, firmly hold the Reader in place until the

glue dries.

9. Carefully re-attach the snap-off front cover of the Reader

and secure the case security screw at the bottom using the

security hex key.

Wiring Instructions

Swipe Family Readers Installation Manual Page 10

5Wiring Instructions

Mifare® Smart Card Fingerprint Swipe Sensor MOC Readers are

supplied with a 7- wire, 18-inch cable.

To connect the Reader to the Controller:

1. Prepare the Reader cable by cutting the cable jacket

back 1¼ inches, and by stripping the wires ½ an inch.

2. Prepare the Controller cable by cutting the cable jacket

back 1¼ inches, and by stripping the wires ½ an inch.

3. Splice the Reader pigtail wires to the corresponding

Controller wires (see Table 1), and cover each connection.

4.If the Tamper output is being utilized, connect the purple

wire to the correct input on the Controller.

5. Trim and cover all conductors that are not used.

Table 1: Wiring the Reader to the Controller

Color Wiring

Black/ Shield Ground

Red Vin

Green Data 0

White Data 1

Brown LED control

Orange Buzzer control

Purple Tamper

Note:

•The individual wires extending from the Reader are color-

coded according to the required Wiegand standard.

•When using a separate power supply for the Reader, this

supply and the Controller’s power supply must have a

common ground. A linear power supply is

recommended.

•Attach the cable Shield wire on the Reader to an earth

ground (best), or to a signal ground connection at the

panel or power supply end of the cable. This

configuration is best for shielding the Reader cable from

external interference.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Rosslare Portale

Rosslare

Rosslare AC-525 Manuale utente

Rosslare

Rosslare AY-Q65 Istruzioni per il montaggio

Rosslare

Rosslare AC-020 Manuale utente

Rosslare

Rosslare AC-B3x Istruzioni per il montaggio

Rosslare

Rosslare MD-N32 Guida alla risoluzione dei problemi

Rosslare

Rosslare AYC-W6500 Manuale utente

Rosslare

Rosslare MD-N32 Guida all'installazione

Rosslare

Rosslare AY-Q64 Istruzioni per il montaggio

Rosslare

Rosslare MD-W11 Manuale utente

Rosslare

Rosslare AY-M26 Manuale

Rosslare

Rosslare AC-215 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente