Rousseau 5000 Manuale utente
Owner’s Manual
ROUSSEAU
ROUSSEAU ROUSSEAU
ROUSSEAU 5000
50005000
5000
& 5000
& 5000& 5000
& 5000
Dust Solution
Dust SolutionDust Solution
Dust Solution
Use caution when removing your ROUSSEAU 5000 hood
from the bag. It is spring loaded and will spring to shape
when removed.
Always
follow safety recommendations and guidelines
provided by the manufacturer of your tools. When in doubt
refer to the applicable owner’s manual or other instructions.
READ THIS,
IT WILL ONLY TAKE A SECOND
Page 1of 4
& 5000
& 5000& 5000
& 5000
-
--
-L
LL
L
Use caution when removing your ROUSSEAU 5000 hood
from the bag. It is spring loaded and will spring to shape
follow safety recommendations and guidelines
provided by the manufacturer of your tools. When in doubt
refer to the applicable owner’s manual or other instructions.
(
Lighted
)
IT WILL ONLY TAKE A SECOND
Page 2of 4
1. Assemble the stanchions
2. Locate the
stanchions so they
do not interfere with
the saw at maximum
bevel and angle.
4. Use the 3 arm knob
, flat
washer and 1” carriage
bolt to mount the hood on
the stanchion.
3. Drill if necessary
and bolt the
stanchions to the tool
platform with the 2”
carriage bolts.
Page 3of 4
NOTE: The ROUSSEAU 5000 or 5000-L (5000) does not have to be right
against the saw fence or squeezed tightly around the saw. Leave room to get
to accessory ports and fence adjusting knobs. If you are using a dust collection
system, even the smallest system will retrieve the fine dust if the hood is not
squeezed tightly about the saw. The stanchions can be pointed in any direction
and can be adjusted to any available height. In short there is no wrong way to
install your 5000. The dust hood attaches to the stanchion assemblies
mounted on the work bench or stand. Ideally the location of the stanchion
assemblies will allow the front of the 5000 to be positioned parallel to the saw
fence with the hood opening (left to right) to be approximately 36”.
The dust ports on some saws
direct the dust outside the hood.
It may be necessary to place
a 45˚ fitting on the saw’s
dust port in order to direct
the dust into the hood.
25”
36”
50”
32”
Above Dimensions are approximate
The dust port at the bottom of
the hood is a 3” ABS coupler.
To adapt to a 2-1/4” shop vac
use a 4” I.D. reducer (i.e. Penn
Industries
part #
D4X
)
Page 4of 4
Parts Identification
WARRANTY: This product has a Limited Lifetime Warranty to
the original purchaser. The warranty applies to defects in
materials and workmanship only. We will repair or replace the
product or part(s) at our discretion. This warranty does not apply
to product failure or defects due to direct or indirect misuse,
abuse, negligence, accidents, alterations, repairs or lack of
maintenance. If items must be returned for warranty service, call
to receive a Return Goods Authorization (RGA) number and
further instruction. Freight costs will be borne by the user.
Ref. Name Qty.
1
Stanchion
2
5/16
-
18 x 2” Carriage
Bolt
2
3
5/16
-
18 KEP Nut
2
5/16
-
18 Wing Nut
5
5/16
-
18 x
3/
” Carriage
Bolt
6
5/16
-
18 x 1” Carriage
Bolt
2
7
5/16
-
18 Washer
2
8
5/16
3 Arm
Knob Female
knob
2
9
1/
-
20 x
5/8” Hex Bolt *
10
1/
-
20 NyLock Nut *
11
Hoop Mount *
2
1392 Port Drive Clarkston, WA 99403
800-635-3416 * 509-758-3954 * Fax 509-758-4991
Email: salesinfo@rousseauco.com * www.rousseauco.com
* Installed
1
2
3
4
5
6
7
8
9
10
11
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Rousseau Accessori per utensili elettrici
