Royal RPL-85 Manuale utente
Powerline Network
© 2009 . All rights reserved. Page 1
RPL-85
User Manual
RPL-85
Powerline Ethernet Bridge
V1.0.0
Powerline Network
© 2009 . All rights reserved. Page 2
PREFACE
This document describes installation of the RPL- 5 Ethernet Bridge Network products.
Please read this document before installing the product.
T
O THE
I
NSTALLER
This publication contains the following sections:
I portant safety instructions
The first thing you need to know before you begin to install
Product installation guide
Specification
Powerline Network
© 2009 . All rights reserved. Page 3
NOTICE:
This product co plies with IC: ICES-006; en confor ité avec IC: NMB-006
IMPORTANT SAFETY INSTRUCTIONS
This product is intended for connection to the AC power line. For installation instructions, refer to the Installation
section. For removing the device, refer to the Unplug section. The following precautions should be taken when using
this product.
Please read all instructions before installing and operating this product.
Please keep all instructions for later reference.
Please follow all warnings and instructions marked on the product.
Unplug the AC coupler fro the wall outlet before cleaning. Use a da p cloth for cleaning. DO NOT
use liquid cleaners or aerosol cleaners
.
DO NOT operate this product near water.
The opening of enclosure near AC plug to face up or frontal, the connector face botto or rear.
This product should never be placed near or over a radiator, or heat register.
This product relies on the building’s electrical installation for short-circuit (over current) protection.
Ensure that a fuse or circuit breaker no larger than 120 VAC 20A or 240 VAC 16A is used on the phase
conductors (all current-carrying conductors).
DO NOT allow anything to rest on the product interconnect cords.
DO NOT locate this product where people may walk on the cords.
Because the RPL- 5 PLC Ethernet Bridge product sends data over the powerline, it is recommended that you
plug directly into a power outlet. Do not plug the device into a UPS or power strip with surge protection. The
5Mbps PLC Ethernet Bridge product has its own power filter for protection against surges.
The product can be operated at an ambient temperature of 40℃
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible
Only a qualified technician should service this product. Opening or removing covers may result in exposure to
dangerous voltage points or other risks.
Unplug the AC coupler from the wall outlet and refer the product to qualified service personnel for the following
conditions:
When the interconnect cords are damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed.
If the product exhibits a distinct change in performance.
IMPORTANT SAFETY INSTRUCTIONS
Powerline Network
© 2009 . All rights reserved. Page 4
THE FIRST THING YOU NEED TO KNOW BEFORE YOU BEGIN TO INSTALL…
1.
Before installing, make sure your PC meets these requirements for hardware installation
Microsoft Windows® 98SE, ME, NT, 2000, XP, Vista, MAC or Linux OS
Pentiu ® 166 MHz processor, equivalent or higher
At least one free Ethernet port for RPL-85 PLC Ethernet Bridge
2. Your PC must not be configured for another network. This means that
No network clients except for Microsoft Network*, Client for Netware* Networks, or Microsoft Family
Logon* are installed
No network services except file and printer sharing for Microsoft Networks or Personal Web Server*
are installed
No network protocols except Microsoft’s TCP/IP, IPX/SPX, NetBEUI, or Net BIOS support for IPX/SPX
are installed
3. Network installation requires two steps
1. Install the RPL- 5 PLC Ethernet Bridge
2. For each PC to be added to the network, repeat the process
4. Check that you have the following parts for each PC on the network
Product installation guide for RPL-85 PLC Ethernet Bridge
1. RPL- 5 PLC Ethernet Bridge
2. Ethernet Cable (CAT 5)
5. Familiarize yourself with the Powerline device connections
There is only one Ethernet port. This is used for the connection with PC, xDSL/Router, Cable Modem, or
Wireless AP.
6. Limitation of the PLC device
To meet the safety regulation, the longest distance between powerline carrier devices will be limited at 200
meter and for in-house use only. More than 200 meter will cause the signal reduction or data loss.
THE FIRST THING YOU NEED TO KNOW
Powerline Network
© 2009 . All rights reserved. Page 5
Product installation guide
I portant:
Do not plug the device into a power strip or surge protector because these devices ay
consist of filter and i pair signal. Also avoid plugging the device right next to noisy sources such
as cell phone charger, Halogen light, Energy saving bulb, noisy desktop co puter, vacuu
cleaner, etc. Both cases result in poor trans ission speed.
To install for the PC local Powerline network
1. Use the supplied Category 5 Ethernet cable to connect Ethernet Bridge and your PC’s Ethernet port.
2. Plug the Ethernet Bridge to outlet.
3. The POWER LED indicator will light on after plugging.
4. You can repeat steps 1 and 2 for connecting the others
.
5. The LINK LED indicator starts blinking when the data communication proceeds on Powerline.
6. The ETHERNET LED indicator starts blinking when the data communication proceeds on Ethernet.
To share a xDSL or cable ode with Internet access service
1.
Connect one Ethernet Bridge to the broadband router
Plug the Ethernet Bridge into an AC outlet.
Plug the provided Ethernet cable into the RJ45 connector of the Bridge and plug the other end of the
cable into an available Ethernet port of the Router.
2.
Connect the other Ethernet Bridge(s) to the PC(s) to share the Internet access
Plug the Bridge into an AC outlet.
Plug the provided Ethernet cable into the RJ45 connector of the Bridge and plug the other end of the
cable into Ethernet port on the PC.
As wireless AP (Access Point) Extender
1.
Connect one Ethernet Bridge to the broadband router
Plug the Bridge into an AC outlet.
Plug the provided Ethernet cable into the RJ45 connector of the Bridge and plug the other end of the
cable into an available Ethernet port of the Router.
2.
Connect the other Ethernet Bridge to the AP
Plug the Bridge into an AC outlet.
Plug the provided Ethernet cable into the RJ45 connector of the Bridge and plug the other end of the
cable into the Ethernet port on the AP.
PRODUCT INSTALLATION GUIDE
Powerline Network
© 2009 . All rights reserved. Page 6
Specification
RPL-85
Ite s Description
Line Rate 5Mbps
Effect Data Rate Up to 25Mbps effective throughput
Frequency Band 4.3~20.9 MHz
Access Methods CSMA/CA
Qos 4 Levels
Modulation OFDM (QAM 256/64/16, DBPSK, DQPSK)
Port One Ethernet port
Standards IEEE 02.3, IEEE 02.3U, HomePlug 1.0.1
Operating Syste Microsoft Window® 9 SE, Me, NT, 2000, XP, Vista, MAC or
Linux OS
Nodes Supports up to 15 nodes per network
Encryption 56 bit DES Link Encryption with key management
LEDs POWER, LINK, ETHERNET
Operating : 0~40℃ Temperature
Storage : -20~60℃
Operating : 10~ 5% Non-Condensing
Environ ent
Relative
Humidity
Storage : 5~90% Non-Condensing
Power Source 100~240 VAC, 50/60 Hz
Certification CE, FCC, HomePlug 1.0.1,
LEDs
POWER On: Power on
Off: Power off
LINK On: Powerline link detected
Blinking: Powerline traffic detected
Off: No Powerline link detected
ETHERNET
On: Ethernet device linked
Blinking: Ethernet traffic detected.
Off: No Ethernet device linked
SPECIFICATION
Indice
Altri manuali Royal Router di rete
Manuali Router di rete popolari di altre marche
NETGEAR
NETGEAR FS526T - Switch Manuale utente
Korenix
Korenix JetNet 5710G Series Manuale utente
Automated Logic
Automated Logic ZN551 Manuale del proprietario
Cisco
Cisco ASR 1000 Series Manuale dell'operatore
EnGenius
EnGenius ESR-9710 Manuale utente
Cisco
Cisco 805 Series Istruzioni operative e di sicurezza