Rtech TIG200PD-DV Manuale utente

www.r-techwelding.co.uk

email: sales@r-techwelding.co.uk

Tel: 01452 733933 Fax 01452 733939

TIG200PD-DV DIGITAL TIG WELDER

Dual Voltage 110V-240V

OPERATION INSTRUCTIONS

Version 2014-1

Thank you for selecting the R-Tech TIG200PD-DV Digital Inverter DC Tig Welder.

The TIG200PD-DV Digital has many benefits over traditional tig welders, including pulse

welding, slope up/down, remote foot option and an industrial 60% duty cycle.

We want you to take pride in operating our TIG200PD-DV Digital as much pride as we have

taken in making this product for you. Please read all information in this manual before

operation

PLEASE EXAMINE CARTON AND EQUIPMENT FOR DAMAGE IMMEDIATELY

When this equipment is shipped, title passes to the purchaser upon receipt from the courier.

Consequently all claims for material damaged in shipment must be made by purchaser against the

transportation company used.

Please record your equipment identification below for future reference. This information can be found on

data plate at rear of machine.

Product TIG200PD-DV DIGITAL

Serial No. ___________________________________

Date of Purchase _____________________________

Where Purchased _____________________________

Whenever you request replacement parts or information on this equipment please always supply

information you have recorded above

This product is covered by 2 years parts and labour warranty, R-Tech will cover costs of collection,

repair and return of welder to you for mainland UK (Other areas are RTB warranty).

External items, torch, earth lead etc are covered by 3 months warranty. Any faults/damage found caused

by customer will be charged pro-rata.

Pay particular attention to the safety instructions we have provided you for your protection

The level of seriousness to be applied to each section is explained below

WARNING

This statement appears where the information must be followed exactly to avoid serious personal

injury.

CAUTION

This statement appears where the information must be following to avoid a minor personal injury or

damage to this equipment.

Introduction

The R-Tech TIG200PD-DV Digital is a member of our field acclaimed family of welding

products. Premium features include:-

1. Inverter power source –more efficient to operate, provides smoother weld characteristics.

2. Full Featured Pulse welding in DC Tig welding mode

3. HF Arc start –Easy arc striking and prolonged tungsten life

4. Slope up / slope down

5. Remote foot pedal option

6. Digital control panel with memory store function.

7. Industrial 60% Duty cycle at 200 Amps @ 40C

Recommended Processes

The R-Tech TIG200PD-DV Digital is recommended for the Tig welding processes within its output

capacity of 200 Amps @240V or 125A at 110V input.

Welding Capability –Duty Cycle

The R-Tech TIG200PD-DV Digital is rated at 200 Amps at 60% duty cycle (240V TIG) on a ten

minute basis. If the duty cycle is exceeded a thermal protector will shut machine off until the

machine cools.

Technical Specifications

Model No.

R-Tech TIG200PD-DV

Input

240V AC 50/60Hz 22A

110V AC 50/60Hz 25A

MMA

No-load Voltage

60V –80V

60V - 80V

Current Range

5A –160A

5A - 100A

Rated Output Current

160A @ 35%

100A @35%

Arc Force

1 - 100%

Hot Start Time

0.1 - 1.5

Hot Start Amps

1 - 100

DC TIG

No-load Voltage

60V –80V

60V - 80V

Current Range

5A –200A

5A - 125A

Rated Output Current

200A

125A

Duty Cycle Tig

60% @200A

60% @125A

Up-Slope Time

0-25 Seconds

Down-Slope Time

0-25 Seconds

Pulse Frequency Range

0.5Hz –500Hz

Pulse Width Range

5% - 95%

Pulse Amperage Range

5% - 95% of base amps

Gas Post Flow Time

0 - 25 Seconds

Gas Pre Flow Time

0 - 10 Seconds

Arc Starting Mode

High Frequency

Gross Weight

18 KG

425 x 195 x 310mm

Insulation

IP23S

Safety Precautions

Read entire section before starting installation

WARNING!

Electric Shock can kill –Only qualified personnel should perform this installation. Turn off input

power at the fuse box before working on this equipment. Do not touch electrically live parts. Always

connect the machine to an earthed mains supply as per national recommended standards.

Select suitable location

Place the welder where clean cooling air can freely circulate in and out of the front & rear louver

vents. Dirt, dust or any foreign material that can be drawn through vents into welder must be kept to

a minimum. Failure to observe these precautions can result in excessive operating temperatures

which can lead to plant failure.

Grinding

Do not direct grinding particles towards the welder. An abundance of conductive material can cause

plant failure.

Stacking

This machine cannot be stacked.

Transport –Unloading

Never underestimate the weight of equipment, never move or leave suspended in the air above

people. Use recommended lifting equipment at all times.

WARNING!

Falling Equipment can cause injury. Never lift welder with gas bottle attached. Never lift above

personnel.

Tilting

Machine must be placed on a secure level surface or on a recommended undercarriage/trolley.

This machine may topple over if this procedure is not followed.

Environmental Rating

The welding power source carries the IP23S rating. It may be used in normal industrial and

commercial environments. Avoid using in areas where water / rain is around.

Read and follow the ‘Electric Shock Warnings’ in the safety section if welding must be performed

under electrically hazardous conditions such as welding in wet areas or water on the work piece.

Electrical Installation

WARNING!

ELECTRIC SHOCK CAN KILL

Machine grounding and High Frequency Interference Protection

This welder must be grounded to earth. See national electrical codes fro proper grounding

methods.

The high frequency generator being similar to a radio transmitter may cause interference to radio,

TV and other electronic equipment. These problems may be the result of radiated interference.

Proper grounding methods can reduce or eliminate this.

Radiated interference can develop in the following ways

1. Direct interference from welder power source

2. Direct interference from the welding leads

3. Direct interference radiated from feedback into power lines

4. Interference from re-radiation by un-grounded metallic objects.

Keeping these contributing factors in mind, installing equipment as per following instructions should

minimize problems.

1. Keep the welder input power lines as short as possible and enclose as much of them as

possible in metal conduit or equivalent shielding. There should be a good electrical contact

between this conduit and ground (Earth).

2. Keep the work and electrode leads as short as possible. Tape the leads together where

practical.

3. Be sure the torch and earth leads rubber coverings are free from cuts and cracks that allow

welding power leakage

4. Keep earth lead connection to work in good condition –Clean area on workbench where

earth clamp is situated on a regular basis.

Input Connections

Make sure the voltage, phase and frequency of input power is as specified on machine rating plate

located at rear of machine.

Have a qualified electrician provide suitable input power as per national electrical codes. Make sure

machine is earthed / grounded.

Make sure fuse or circuit breaker is correct rating for machine. Using fuses or circuit breakers

smaller than recommended will result in ‘nuisance’ shut off from welder inrush currents even if

welding at low amperages.

Failure to follow these instructions can cause immediate failure within the welder and void

machines warranty.

Turn the input power OFF at the mains switch & fuse box before working on this equipment.

Have a qualified electrician install & service this equipment.

Allow machine to sit for 5 minutes minimum to allow the power capacitors to discharge before

working inside this equipment. Do not touch electrically live parts

The TIG200PD-DV DIGITAL Inverter Tig Welder requires a 110V/240V 50/60Hz supply. It comes

with a 3 metre mains cable attached.

Connect wires according to national coding.

Brown wire –Live

Blue wire –Neutral

Green/Yellow Wire –Earth (Ground)

Connecting to a mains electrical supply

THIS MACHINE IS OF AN INDUSTRIAL SPECIFICATION AND MUST BE

FITTED TO A MINIMUM of 32AMP 110V or 240V MAINS INPUT FOR FULL

OUTPUT RANGE TO BE ACHIEVED.

This machine is auto sensing of input voltage, no need for any internal

changes, simply plug into either 110V or 240V supply and machine will

set itself to correct input mode.

Connecting to an Engine Driven Generator

If connecting this machine to an engine driven generator please ensure the

following

Minimum Generator KVA Output –7.5 KVA continuous

Generator to be fitted with AVR (automatic voltage regulation)

DO NOT USE ON A GENERATOR WITHOUT AVR

Connecting to a generator without the above minimum requirements will in-

validate your warranty.

Connections for TIG200PD-DV Digital

Rear machine connections

Fig 1

1. On/Off Switch

2. Earth for chassis

If experiencing localized interference when using machine, connect workbench to this point

using correct graded earth wire (not normally used)

3. Gas input connector

Connect input gas hose ensuring connection is tight

4. Mains input cable

Fit required plug as per your electrical installation

Connections for TIG (GTAW) Welding

Fig 2

1. Negative power connector -

Connect Tig Torch Dinze to power connector by inserting and twisting until tight

ENSURE TIG TORCH IS FITTED TO NEGATIVE CONNECTOR OTHERWISE YOU WILL

EXPERIENCE TUNGSTEN BURNBACK

2. Gas outlet - Quick release type

Connect the torch gas hose

3. Positive power connector +

Connect the earth lead to by inserting and twisting until tight and the earth clamp to

work/bench

4. Torch control socket 7-Pin

Connect torch control plug

To avoid a High Frequency shock keep the Tig torch in good condition and replace if any of the

insulation is damaged.

Connect the gas input hose to gas regulator and use ‘Pure Argon’ Gas, available from local

suppliers. Set gas flow/pressure to 8-12 LPM. Make sure gas bottle is secured to avoid injury.

Remote Foot Pedal connection.

Disconnect Tig Torch switch plug from torch control socket (Fig2.4) and connect plug from foot

pedal.

Connections for STICK MMA (SMAW) Welding

Fig 3

1. Negative power connector -

Connect the earth lead to by inserting and twisting until tight and the earth clamp to

work/bench.

2. Positive power connector +

Connect the electrode holder by inserting and twisting until tight

Indice

Altri manuali Rtech Sistema di saldatura

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente