RTI XP-3 Istruzioni operative
1
It’s Under Control®
XP-3
Installation and Operation Guide
70-210093-22 V1.0
Remote Control Processor
It’s Under Control®
Remote Control Processor
XP-3
2
Copyright © 2011
Remote Technologies Incorporated
All rights reserved.
3
It’s Under Control®
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. Any changes or modications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the device.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received including
interference that may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION NOTICE
DECLARATION OF CONFORMITY (DOC)
The Declaration of Conformity for this product can be found on the RTI
website at: www.rticorp.com/declaration
N27917
FCC ID: MMURTI1900
IC (Canada): 3166A-RTI1900
Remote Control Processor
XP-3
4
Read Instructions. Read all safety and operating instructions before
operating the unit.
Retain Instructions. Keep the safety and operating instructions for
future reference.
Heed Warnings. Adhere to all warnings on the unit and in the
operating instructions.
Follow Instructions. Follow operating instructions and instructions
for use.
Heat. Keep the unit away from heat sources such as radiators, heat
registers, stoves, etc., including ampliers that produce heat.
Power Sources. Connect only to the power supply that was included
with the unit.
Power Cord Protection. Route power supply cords so that they are
not likely to be walked on or pinched by items placed on or against
them, paying particular attention to the cords at plugs, at convenient
receptacles, and at the point at which they exit from the unit.
Water and Moisture. Do not use the unit near water—for example,
near a sink, in a wet basement, near a swimming pool, near an open
window, etc.
Object and Liquid Entry. Do not allow objects to fall or liquids to be
spilled into the enclosure through openings.
Cleaning. The unit should be cleaned only as recommended in this
installation and operation guide.
Servicing. Do not attempt any service beyond that described in
the operating instructions. Refer all other service needs to qualied
service personnel.
Damage Requiring Service. The unit should be serviced by qualied
service personnel when:
Objects have fallen or liquid has been spilled into the unit.
The power supply cord or the plug has been damaged.
The unit does not appear to operate normally or exhibits a
marked change in performance.
The unit has been dropped or the enclosure has been damaged.
WARNING!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.
SAFETY SUGGESTIONS
5
It’s Under Control®
Remote Technologies Incorporated warrants its products for a period of one
(1) year from the date of purchase from Remote Technologies Incorporated
or an authorized Remote Technologies Incorporated distributor.
This warranty may be enforced by the original purchaser and subsequent
owners during the warranty period, so long as the original dated sales
receipt or other proof of warranty coverage is presented when warranty
service is required. Except as specied below, this warranty covers all
defects in material and workmanship in this product. The following are not
covered by the warranty:
Damage resulting from:
1. Accident, misuse, abuse, or neglect.
2. Failure to follow instructions contained in this Guide.
3. Repair or attempted repair by anyone other than Remote Technologies
Incorporated.
4. Failure to perform recommended periodic maintenance.
5. Causes other than product defects, including lack of skill, competence
or experience of user.
6. Shipment of this product (claims must be made to the carrier).
7. Being altered or which the serial number has been defaced, modied
or removed.
Remote Technologies Incorporated is not liable for any damages caused by
its products or for its failure of its products to perform, including any lost
prots, lost savings, incidental damages, or consequential damages.
Remote Technologies Incorporated is not liable for damages based upon
inconvenience, loss of use of the product, loss of time, interrupted
operation, commercial loss, any claim made by a third party or made by
you for a third party.
Remote Technologies Incorporated’s liability for any defective product is
limited to repair or replacement of the product, at our option.
If your XP-3 Remote Control Processor needs service, please contact
Remote Technologies Incorporated by telephone, fax or E-mail for return
information. Please do not return products to Remote Technologies
Incorporated without return authorization.
LIMITED WARRANTY
Remote Control Processor
XP-3
6
DISCLAIMER
All rights are reserved. No part of this document may be photocopied,
reproduced, or translated without the prior written notice of Remote
Technologies Incorporated.
The information contained in this document is subject to change without
notice. Remote Technologies Incorporated shall not be liable for errors or
omissions contained herein or for consequential damages in connection
with the furnishing, performance, or use of this guide.
Microsoft, Windows, Windows XP, Windows Vista and Windows 7 are
registered trademarks of Microsoft Corporation in the United States and
other countries. ZigBee is a registered trademark of the ZigBee Alliance.
XP-3, Integration Designer, and the RTI logo are registered trademarks of
Remote Technologies Incorporated.
Other brands and their products are trademarks or registered trademarks
of their respective holders.
7
It’s Under Control®
Federal Communications Commission Notice...............3
Safety Suggestions...................................................... 4
Limited Warranty ........................................................5
Disclaimer ...................................................................6
Table of Contents ........................................................7
Chapter 1 - Welcome ................................................... 9
Important Notes, Compatibility, Software Req’s............ 9
Product Contents, Unpacking.................................... 10
Chapter 2 - Features...................................................11
XP-3 Diagram......................................................... 12
Chapter 3 - Installation and Operation .......................13
Mounting ............................................................... 13
Power ................................................................... 14
Connections (Antennas, IR, Modules, etc.) ................. 14
RS-232 Cabling/Pinouts ........................................... 16
Programming the XP-3 ............................................ 17
Status LED reference............................................... 17
Setting the Zone Code............................................. 17
Connection Diagrams .............................................. 18
Chapter 4 - Specications........................................... 21
Chapter 5 - Troubleshooting....................................... 23
Chapter 6 - Service and Support................................. 25
Index ......................................................................... 27
TABLE OF CONTENTS
Remote Control Processor
XP-3
8
9
It’s Under Control®
Thank you for using the XP-3 Remote Control Processor.
The XP-3 is designed to automate and enhance the operation of A/V,
security, lighting, HVAC, and countless other devices in a commercial
or residential environment. The XP-3 is packed with features including
a variety of control options, such as two-way RS-232, relays, Ethernet,
and routable IR. The processor also has a built-in 2.4 GHz ZigBee®RF
transceiver for sophisticated bidirectional communication with compatible
RTI remote controls. The XP-3 can also be congured to support 433MHz
RF communication using additional RTI accessories and wireless remotes.
For complete control in any room, the XP-3 even allows powerful two-way
control with Ethernet enabled RTI in-wall controllers, and reliable one-way
control with compatible RTI in-wall products.
IMPORTANT NOTES
Please read these important notes about the XP-3:
The XP-3 should be placed in an area where it is around normal room
temperature (between 60°F to 90°F).
Avoid installing the XP-3 in a location where it can come in contact
with direct sunlight.
Do not let the XP-3 get wet. It should not be handled with wet hands
or placed in an area where it could get wet.
Do not subject the XP-3 to smoke, dust, or vibrations.
Only use the power supply that is specied for the XP-3. Using the
wrong type of power supply may result in damage.
Do not disassemble the unit. Service of the XP-3 should be performed
by authorized personnel only. Service of the XP-3 performed by
unauthorized personnel will invalidate its warranty.
SOFTWARE REQUIREMENTS
The recommended minimum system requirements needed to run the
Integration Designer®software are as follows:
Windows XP®, Windows Vista®, Windows 7®or later version of Microsoft
operating system.
CHAPTER 1 | WELCOME
Remote Control Processor
XP-3
10
Contents within the box include the following items:
• One (1) XP-3 Remote Control Processor
• One (1) Installation Guide
• One (1) Universal Power Supply
• One (1) Power Cord
• One (1) RS-232 Adapter
• Two (2) Phoenix Connectors
• One (1) XP-3 Removable Antenna
• One (1) XP-3 Mounting Plate with screws
UNPACKING AND INSPECTION
After unpacking your new XP-3 Remote Control Processor, save all of the
packing materials in case you ever have to ship the unit.
Thoroughly inspect the XP-3 and packing materials for signs of damage.
Report any damage to the carrier immediately. Report any equipment
malfunctions to RTI or an authorized RTI distributor.
CHAPTER 1 | PRODUCT CONTENTS
Altri manuali per XP-3
1
Indice
Altri manuali RTI Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
