RTS KP-32 Manuale utente
1
Installation Guide
CSI-100 Coaxial System Interface
9330-7693-000 Rev A 11/02
STEP 1
The CSI-100 can only be field installed in
KP-32 series equipment if the rear panel has
a knockout provided for the BNC connector
on the CSI-100 board. See Figure 1 for the
location of the knockout. If the knockout is
present, proceed to STEP 2. If the knockout
is not present, the CSI-100 can be installed,
but requires factory level modifications.
Contact RTS for pricing and instructions.
STEP 2
The backpanel and top cover of the keypanel
must be removed in order to install the CSI-
100. Begin by turning the unit over and
remove the three screws along the bottom of
the back panel as shown in Figure 2.
STEP 3
Turn the unit over. Remove the ten screws
that secure the top cover on the unit. See
Figure 3.
STEP 4
Remove the two standoffs on the 9-pin D-
sub connector. You may also need to remove
additional screws from the GPIO board if
present. See Figure 3.
STEP 5
Remove the four screws securing the back
panel to the keypanel frame. If a GPIO board
is present, be careful to not disturb any of
the wiring harness for the board. See Figure
3.
STEP 6
Locate the accessory connector on the
keypanel motherboard. See Figure 4.
STEP 7
Locate the mating connector on the bottom
of the CSI-100 board. See Figure 5.
STEP 8
With the BNC connector on the CSI-100
board facing out from the unit, slide the
connector of the CSI-100 board onto the
Figure 2 - Bottom screw locations for backpanel removal.
Figure 3 - Top and rear screw/standoff locations for backpanel removal.
Figure 1 - CSI-100 coaxial connector location on backpanel.
2
Figure 5 - Bottom view of CSI-100 board.
Figure 4 - Accessory connector on KP-32 series board.
Figure 6 - View of installed CSI-100 board.
accessory connector on the keypanel
motherboard being careful to align the
mating pins properly.
STEP 9
Remove the knockout on the backpanel to
allow the BNC on the CSI-100 board to pass
through the backpanel.
STEP 10
Place the backpanel on the keypanel and
then place the washer(s) and nut over the
BNC connector and tighten.
STEP 11
Repeat steps 5 through 3 in reverse to
reassemble the keypanel.
END OF PROCEDURE
Altri manuali per KP-32
2
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali RTS Apparecchiature di registrazione
RTS
RTS IFB-828 Manuale utente
RTS
RTS OMNEO Manuale utente
RTS
RTS KP 32 CLD Manuale utente
RTS
RTS SIP-ISDN Istruzioni per il montaggio
RTS
RTS WKP-8 Manuale utente
RTS
RTS OMNEO OEI-2 Manuale utente
RTS
RTS TIF-2000A Manuale utente
RTS
RTS OMI-2 Manuale utente
RTS
RTS DSI 2008 Manuale utente
RTS
RTS Zeus III Manuale utente
Manuali Apparecchiature di registrazione popolari di altre marche
Strymon
Strymon NIGHTSKY Manuale utente
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente
Tews Technologies
Tews Technologies TPMC465 Manuale utente
Honeywell
Honeywell Excel 50 Manuale utente
SeaLevel
SeaLevel COMM+8.LPCI Manuale utente
Arturia
Arturia AUDIOFUSE STUDIO Manuale utente
