Rugged Radios GMR45 Manuale utente
GMR45
USER MANUAL
2
The GMR45 operates on GMRS (General Mobile Radio Service) frequencies, which require a
Federal Communications Commission (FCC) license. You must be licensed prior to operating
on channels 1-7, 15-22 or RP15-22 which comprise the GMRS channels of the GMR45.
Serious penalties may result from unlicensed use of GMRS channels, in violation of FCC rules,
as stipulated in the Communications Act’s Sections 501 and 502 (amended). You will be
issued a call sign by the FCC that should be used for station identification when operating your
radio on GMRS channels. You should also cooperate by engaging in permissible transmissions
only, avoiding channel interference with other GMRS users, and being prudent with the length
of your transmission time
To obtain a license or ask questions about the license application, contact the FCC at
1-888-CALL-FCC or go to the FCC’s website: http://www.fcc.gov and request Form 605.
FCC NOTICE
3
User Safety Information
Package Includes
Main Features
Initial Installation
Mobile Installation
DC Power Cable Connection
Replacing Fuses
Antenna Connection
Installing the Antenna
Accessory Connections
5-Pin Cable
External Speaker
Getting Acquainted
Front Panel Operation
Rear Panel Operation
Display
Microphone
Additional Features
Troubleshooting
Tone Codes
Changing Tone Codes
CTCSS
DCS
04
05
06
07
07
09
11
12
13
14
14
15
16
16
17
18
19
20
21
22
22
23
24
Standard GMRS Channels
GMRS Repeater Channels
Specifications
General
Receiver
Transmitter
Notes
CONTENTS
25
26
27
27
27
28
29
4
• Do not attempt to configure your radio while driving.
• This radio is designed for a 13.8V DC power supply. Do not use a 24V battery to
power on the radio.
• Do not place the transceiver in excessively dusty, humid or wet areas, nor unstable
surfaces.
• Please keep it away from interference devices (Such as TVs, generators, etc.)
• Do not expose the radio to long periods of direct sunlight or place it close to heating
appliances.
• If an abnormal odor or smoke is detected coming from the radio, turn off the power
immediately and contact your dealer.
• Do not transmit with high power for extended periods or the radio may overheat.
USER SAFETY INFORMATION
5
• Radio unit x 1
• Hand Mic x 1
• Mobile mounting bracket x 1
• DC power cable with fuse holder x 1
• Screw packs x 1
• Protection fuses x 1
PACKAGE INCLUDES
6
MAIN FEATURES
FEATURES:
Go Further with our industry leading 45-watt GMR45 mobile radio. More wattage equals
more power and range, giving you the ability to transmit long-distances when it matters.
Easily connect to intercom, headset, or any 5-pin accessory with the built-in Rugged Ready
pigtail cable! Loaded with channels and features, the GMR45 is ideal for installation into your
vehicle or setup at base camp.
• 45 Watt Radio
• 8 Repeater Channels
• 15 GMRS Channels (1-7 & 15-22)
• Easily connect to intercom, headset, or any 5-pin accessory with the
built-in Rugged Ready pigtail cable!
• Battery Voltage Display
• Adjustable Squelch
• KeyPad Lock
• External Speaker Port
• Clear Backlit Display
• Channel Scan Mode
• Dual-Tone Multi-Frequency (DTMF)*
*Enabled via software available from RT Systems.
MOUNTING BRACKET
TAPPING SCREW
(M5X20MM)
WASHER (M5)
CAR BODY
7
1. Install the mounting bracket in the vehicle using the supplied self-tapping screws and
flat washers.
INITIAL INSTALLATION
Mobile Installation: To install the radio select a safe and convenient location inside your vehicle
that minimizes danger to your passengers and yourself while the vehicle is in motion. Consider
installing the unit at an appropriate position so that knees or legs will not strike it during
sudden braking of your vehicle. Try to pick a well ventilated location that is shielded from direct
sunlight.
Caution: Extreme care should be exercised when drilling into dash to avoid damage to under
dash components.
MOBILE INSTALLATION
8
INITIAL INSTALLATION
• Determine the appropriate angle of the radio using the 3 screw hole positions on the side of the mounting bracket.
• Double check that all screws are tightened to prevent vehicle vibration from loosening the bracket or radio.
2. Position the radio, then insert and tighten the supplied hex/Phillips screws.
MOBILE INSTALLATION (CONT.)
9
INITIAL INSTALLATION
DC POWER CABLE CONNECTION
The vehicle battery must have a nominal rating of 12V. Never connect the radio to a 24V
battery. Be sure to use a 12V vehicle battery that has sufficient current capacity. If the
current to the radio is insufficient the display may darken during transmission or transmitting
output power may drop dramatically.
1. Route the DC power cable supplied with the radio directly to the vehicle’s battery
terminals using the shortest path from the radio. We suggest you do not use the
cigarette lighter socket as some cigarette lighter sockets introduce an unacceptable
voltage drop. The entire length of the cable must be dressed so it is isolated from heat,
moisture and the engine secondary (high voltage) ignition system/cables.
2. Confirm the correct polarity of the connections, then attach the power cable to the
battery terminals: Red connects to the positive (+) terminal and black connects to the
negative (-) terminal.
10
INITIAL INSTALLATION
DC POWER CABLE CONNECTION (CONT.)
3. Connect the DC power cable to the radio’s power supply connector. Press the
connectors firmly together until the locking tab clicks.
Altri manuali per GMR45
1
Indice
