Ryobi HBG620 Manuale operativo

Indice

Altri manuali Ryobi Macinacaffè

Manuali Macinacaffè popolari di altre marche

Parkside

Parkside PWS 230 C3 Manuale utente

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manuale tecnico

PTA

PTA P1322 Manuale utente

Crown

Crown CT13313 Manuale utente

Parkside

Parkside 280250 Manuale utente

Climax

Climax VM2150 Series Manuale utente

Jet

Jet JPSG-618M1 Manuale di servizio

Makita

Makita GA4030 Manuale utente

DeWalt

DeWalt DWEN202 Manuale utente

Grizzly

Grizzly G2790 Manuale utente

Fein

Fein MSf843-1a Manuale utente

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manuale utente

RAMSET

RAMSET CBAGR18 Manuale utente

Bosch

Bosch 8-115 Z Manuale utente

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manuale utente

MW TOOLS

MW TOOLS ME15W Manuale utente

Caravaggi

Caravaggi SP 20 Istruzioni operative

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manuale tecnico

HBG620

4

1 2

3

1

1

7

7

6

5

8

9

2

2

10

7

3

4 5

6 7

6

9

5

10 10 3

230V,50Hz

250W

2850min-1

Ø150x20xØ12.7mm

8.5kg

BENCH ATTACHMENT (Fig. 3)

1. Fasten grinder to work bench before operating this machine.

There is a bench attachment hole(6) on either side of the base

which should be used to secure the grinder.(Fig.3)

2. 2 x 10mm diameter bolts should be used to secure the grinder

to the bench or stand.

AUTO ON LIGHT (Fig. 4)

GLOBE REPLACEMENT

COOLANT TRAY (Fig. 5)

OPERATION

EYESHIELD ADJUSTMENT

TOOL RESTS ADJUSTMENT

CHANGING THE GRINDING WHEELS

Your RYOBI bench grinder comes complete with an auto on

adjustable light (9) which allows you to illuminate the grinding

wheels and workpiece when operating in dark areas. The light will

automatically come on when the grinder is switched on. When

grinder is not in use, switch off the tool to avoid overheating of the

lamp.

When the globe is worn out and will no longer work gently remove

the bulb from the holder by pushing in and turning anticlockwise.

Use only RYOBI genuine replacement part 12 volt, 21 watt globe.

To replace gently push the globe into the insert and turn clockwise.

IMPORTANT: Do not use force as this could lead to the globe

breaking and serious injury.

The in-built coolant storage dip tray (5) allows you to cool

overheated workpieces. Simply pull out the tray and half fill with

appropriate coolant.

NOTE: The height and angle of eyeshields can be adjusted up and

down to the user's riquirement.

Voltage

Power input

No load speed

Disc size

Net weight

1. Spark breaker

2. Eye shield

3. Grinding wheel

4. ON/OFF switch

5. Coolant tray

6. Bench attachment hole

7. Tool rest

8. Opti eye shield

9. 12V Light

10. Wheel dressing tool

7

2

ASSEMBLY (Fig. 1, 2 )

WHEEL DRESSING TOOL (Fig. 6, 7)

After extensive use, the grinding wheels (3) will accumulate

in-ground metal build up. To clean the wheels detach the wheel

dressing tool (10) from the storage holder (Fig.6)

Rest the wheel dressing tool (10) on the tool rest approx. 5mm

from the grinding wheel (2). Switch on the grinder and wait a few

seconds until the grinding wheel reaches full revolution then

slowly move the dressing tool to gently touch against the

grinding wheel holding firmly with two fingers. Do not use

excessive pressure. (Fig.7)

CAUTION: Do not allow the grinding wheel and dressing tool to

touch before the grinding wheel has reached high speed as this

may cause the dressing tool to be flicked from your grasp

causing serious injury.

To ensure safety and reliability, all repairs should be

performed by an AUTHORIZED SERVICE CENTER or

other QUALIFIED SERVICE ORGANIZATION.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING!

After use, check the tool to make sure that it is in top

condition. It is recommended that you take this tool to a

RYOBI Authorized Service Center for a thorough cleaning

and lubrication at least once a year.

DO NOT MAKE ANY ADJUSTMENTS WHILE THE

MOTOR IS IN MOTION.

ALWAYS DISCONNECT THE POWER CORD FROM THE

RECEPTACLE BEFORE CHANGING REMOVABLE OR

EXPENDABLE PARTS (BLADE, BIT, SANDING PAPER

ETC.), LUBRICATING OR WORKING ON THE UNIT.

MAINTENANCE